pod model

phone_model_customized = Yes, it is now set at 0 custom_left_port_y_position_disabled = No, has been set by the default of 0 as requested above bottom_port_corner_radius_customization_enabled = Yes, now has a custom setting equal to 5...

The spacer is to put between the 5015 fans and the cover, if your spacing is larger/smaller just scale the spacer on the Z axis to match your setup. The hole for the mounting screw is designed to be 4mm in diameter, but if yours end up being...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

I could not prevent warping completely but using a strong construction lamp to heat up the model seemed to improve the result. I am glad for any tips on how to prevent warping. (I am new to 3D printing and so far brims did not prevent warping, and...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

THE FULL SET OF BASE BLING CAN BE FOUND HERE: https://cults3d.com/en/3d-model/game/basebling-magnetic-base-system-for-fantasy-football ** BaseBling Magnetic Base + Rings System ** ** For Fantasy Football ** BaseBling is a modular miniature basing...

These elevator models have been designed with very specific fit tolerance, to make these pieces fit tightly but not too much that you can't snap them together. Here are some general considerations:Print with PLA. But they also work with PETG, ABS,...

In many channels for the promotion of new electric bikes, people who access the channels, like me, are also excited about the new models of electric bikes, almost always great projects. However, many were frustrated because they would like to have...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

He shipped back a huge quantity of Parian marble to use for his ethnographic portraits of Greeks, especially for portraits of the peoples of Paros, and eventually realizing at least twenty-seven busts, medallions and full scale figures representing...

 I've included 3mf project files from PrusaSlicer so you can see how I ran this model on my printers. UPDATE 27/01/2022: Created a rudimentary mount to hang the chassis under a shelf or table.  I decided to make a second unit to move...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

(ähnlich wie das hier: https://www.printables.com/de/model/145016-credit-card-sized-folding-phone-stand-v11)in den Schutzboxdeckel könnte man eine kleine Kamera integrierenFeedback and Support:Hier über PN erreicht Ihr mich direkt für Feedback,...

Fits both "Research" and "Research Plus" models.Don't loose precious time with clips or carousels!Print your holder now ;-)Materials required4mm aluminum rod (2x 18cm minimum)2x M5 20mm screw with hex head2x M5 butterfly nut2x M5 washerSuperglue or...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Among the first risen humans in Draksborne, Violet thought herself to be insane for her first life upon Tharador. For when she woke she remembered all that had...

 If you intend to use Sovol's SV06 Plus hotend, you'll have to get or make a duct that will work with the tall heatblock.I included a few models from Sovol's github, to include their extruder knob and extruder release lever, for no purpose other than...

The "Advanced_Fit" version is meant for printers with tighter tolerances and may provided better heat break cooling due to the extended cooling channel.** After looking at all the options for a hotend mount here on Thingiverse and Facebook i decided...

In my 4 months of using it non-stop it has never come loose or moved, the force needed to take it off the rail is a bit more than the force needed to make the motor skip steps so something would have to go CATASTROFICALLY wrong to make the tool...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

I recommend 3 loops since this is quite a small model. Otherwise not enough PETG is dumped before the start of the parts</p><p>Print bed recommendation: Powder coated steel sheet with glue stick. I usually just put a 5cm to 10cm light line on the...

If you have a dual-extruder that can print dissolvable, or you just want to go for printing with supports, check out his remix of my model! OTHER PROJECTS: Another day, another project. If you like Space RTS games, check out our latest project on...

Update 3/10/18 - I used jzkmath's model of the assembled Prusa i3 mk3 with the r2 components and found that my tensioner still works with the r2 belt holder, maintaining a parallel belt path. Update 2/28/18 - Please refer to the picture in Slic3r...

In other words, it proposes theoretical models that serve as a reference for setting goals and strategies. 3. Children's pedagogy Teaching during the first years of life is very important , since in this period is when people are most...

Printer Settings: * Printer Brand: RepRap * Printer Model: Original Prusa i3 * Rafts: No * Supports: No * Resolution: 0.2mm * Infill Percentage: 25% Print Notes: I utilized a 0.8mm nozzle to expedite the printing process, which took approximately...

This ring is the original base for the stand-alone Grabhole adapter: https://cults3d.com/en/3d-model/tool/grabhole-qr-adapter-sal This QR adapter for the Rapido v3 anamorphic clamp...

Un de ces enjeux, particulièrement dans le domaine de l'impression 3D FDM/FFF (Fused Deposition Modeling/Fused Filament Fabrication), est la gestion des déchets générés par les bobines en plastique vides. Chaque fois qu'une bobine de filament 3D...

Print Settings Printer: FlashForge Rafts: No Supports: No Resolution: .2mm (Medium) Infill: 20% Doesn't matter Notes: For the most part, I intended these to print without supports; however, the housing is so wiggly that it needed some once I...