print source 3d models

... using the Customizer! ...(http://www.thingiverse.com/apps/customizer/run?thing_id=83325). For printing, use image_file "stampmaker_v0320130625-1537-15c8lh7-0.dat", set layer_height to 0.5, scale at 1.0, keep handle_height as 0 and print with 20 layers.

This is a robust 3D-printable vise, featuring 100% 3D-printed components - no metal parts are included (except for attachment to the table). Critical sections include shaft part two and lever; these pieces require horizontal printing. In my setup, I...

I print from the axis upwards with support, which gives a smooth surface.Also nice with two Colors ;-) But I should use manual Filament-change next time.

Here is a modified version of the Podracer from TBS. ... I coordinated it with mr_Ho to get an ideal level of stiffness & weight (8.65g). Print settings: - Printspeed: 35mm - Material: TPU - Support: yes - Capacitor: Panasonic 35v 680uF

You may want to resize them if you have an uneven resting place for it.It's best to set a 0.2mm layer height so the radius on the bottom of the body prints properly. ...Also, with some slight fiddling both the body and tray can print at the same time on...

This steadicam is constructed from PVC plumbing, metal plates, nuts and bolts, BMX grips, and innovative 3D-printed components specifically created for this project. If you're interested in building your own steadicam based on a similar design or...

Here's a summary of the required components: **Single Motor Steering System** * Mini Servo * (2) 3mm ID flanged bearings * Stainless Steel Fasteners: + (3) M3x8mm + (1) M3x10mm + (1) M3x20mm + (1) M3x30mm + (3) M3x50mm + (5) M3 Nylon Locking Nut +...

Having printed, remixed and liked barneyj's 3DR Radio Case (air), I've once again scaled up barneyj's case to suit another RC vehicle electronic pcb. This particular version of this outstanding case measures approximately 60mm by 32mm and features...

**Printing Settings:** Printer: * **Model:** Prusa variant * **Features:** Supports Available Resolution: * **Recommended:** 0.2mm minimum resolution guaranteed to produce quality results. Infill Percentage: * **Optimal Value:** 80% is a sweet spot...

<p>This uses 3x3mm magnets in the rear of the model. ...Just print as normal, insert magnets with a small dot of super glue on the back.&nbsp;I do not own the rights to any Valve logos or art.&nbsp;

This Pod is a remix from : https://www.thingiverse.com/thing:4516235/files The Canopy is optimized for Sharkbyte, printed in TPU. 5mm more in high. 3mm more lens protection. Made the front bigger for stiffness. Added a turtle mode fin with...

... connector, antenna, and receiver. ...I fabricated it using PLA filament with a 30% infill density and no support structures required. When printing, make sure to rotate the model 90 degrees so it sits flat like it would be positioned within the frame.

... involved assembling the ten elements in series, functioning as the fuel components within a nuclear reactor. However, these designs would require input from NASA. Fortunately, Uranus won't need to be printed (it will be handled by another company).

**Hardware Components** - Raspberry Pi Zero W - Camera Module - Camera Cable compatible with Raspberry Pi Zero - 5.1V micro USB Power Supply - MicroSD Card At the bottom of the enclosure there is an inner thread to attach the 3D-printed stand...

I decided to give the new Modifier feature in PrusaSlicer a try, allowing me to create a section of a print with varying layer heights that would show only infill without top or bottom layers. The result looked eerily similar to Josef Prusa's tattoo...

Having printed, remixed, and liked barneyj's 3DR Radio Case (air) [http://www.thingiverse.com/thing:40483, http://www.thingiverse.com/thing:712588], I've scaled up the case once again to fit another RC vehicle electronic PCB. ...This version of the...

For now, if you print one, you'll need a NEMA 17 stepper motor, a motor controller, and a power supply with a rheostat, along with various lengths of M5 bolts and nuts, some M5 washers, an M8 bolt and nut, several M8 washers, and at least one...

My goal with this project is to ensure that at least some sort of ventilator may be available for remote areas that may have a 3d printer. Print instructionsCategory: DIY Summary This is a 3d printed Emergency Ventilator offered under the Good...

I printed this with an Ultimaker printer at 0.2mm layer height, 0.8mm wall thickness, and 30% fill density. ...You can find additional OpenSCAD and Inkscape files for assistance, along with tutorials on tweaking Inkscape vectorial files and exporting...

A friendly note: if you use a spring action or nitro piston air rifle, it's best to cast these prints in lead or another metal as shooting plastic pellets from these types of airguns can cause the same damage as dry firing. Please enjoy the sport...

This kit includes several key components: * A cam mount * An air unit mount with an integrated adjustable antenna mount (requires M3x22mm and Nyloc fasteners for assembly) The air unit mount must be printed using TPU 98A material to achieve a rigid...

I thought I'd try and use the new Modifier feature in the PrusaSlicer where you can make a part of a print (layer height dependant) have no top or bottom layers but only show the infill. ...Ended up looking like Josef <a...

You should adjust the voltage regulator accordingly VTX:akk fx2 ultimate...

... * Control Box Back Panel - Vents Only.FCStd: A FreeCAD file for the back panel of the control box with vents. These files are designed to be used with 3D printing software and can be used to create the various components of the control box.

Hydrapack spare part for Source, easy to print

TBS Source One SMA Antenna mount Print in TPU https://www.tinkercad.com/things/hwBa2waeGs1-tbs-source-one-antenna-mount/edit

Filament swatch inspired by the open source logo. ...Great for displaying different types of filament and showing your open source pride! ...Printed a 0.3mm layer height, and takes 30 minutes to print!

Simple Open Source Hardware coasterOptimal print settings: 0,15mm QUALITY, no supports, infill 15% - 100%Set filament change to layer 21&nbsp;Jednoduchý Open Source Hardware podtácekOptimální nastavení tisku: 0,15mm QUALITY, bez podpěr, výplň 15% -...

source one 11

There are numerous open-source hardware logos available, but no specific open-source keychain logo. To rectify this, I created an open-source logo, similar in size to Kevin's open-hardware keychain from kevinkline4124. Since there were no source...