prusa i3 mk3 psu 3d models

I slightly modified the original Prusa i3 mk3 PSU cover to gain a few centimeters when using the Ikea Lack table enclosure ( https://www.thingiverse.com/thing:2864118 ) The original file of the PSU cover come from Prusa3D web site :...

I slightly modified the original Prusa i3 mk3 PSU cover to gain a few centimeters when using the Ikea Lack table enclosure ( https://www.thingiverse.com/thing:2864118 ) The original file of the PSU cover come from Prusa3D web site :...

MK3 PSU cover

Fan holder and cover plate for Prusa i3 Mk3 power supply. Mounts two 40 mm, 12 volt fans wired in series to help keep the power supply cooler. The fan holder and cover plate simply hook into the slots in the PSU. ...The fans I used draw 0.04 amp and are...

... plate simply hook into the slots in the PSU. The fans I used draw 0.04 amp and are a negligible extra load on the PSU. Print Settings Printer Brand: Prusa Printer: i3 MK3Resolution: 0.15mm Optimal Infill: 20% Category: 3D Printer Accessories

Simple Wall Mount for Prusa MK3 PSU. ... Look at my TOP Holder https://www.thingiverse.com/thing:3462040

Just an other Prusa MK3 PSU-Bracket / Brace. Please have a look here https://www.thingiverse.com/thing:3898665 It fit's between Mainframe and Rearplate, clicks in top an sidewise in the 3030 Extrusion to make it more stiff. You can Screw it...

So I decided to remix the original prusa MK3 PSU cover to allow it to be mounted outside on the side of the closet. You will need to drill holes for the PSU cables to go into the wall it is mounted on (the cables go out the same way the stock cover...

To achieve this I rotated the aluminium extrusion that usually holds the PSU by 90 degrees so that the two T-nuts are now facing outward on the side rather than upward. This allows a replacement brace to be mounted so that the loads are more in line...

Prusa i3 MK3 LCD_PSU Mod v3.stl (New, Not Tested) Two Versions from the Cover: Prusa i3 MK3 LCD_PSU Mod_Cover_Switch v2.stl (New, Not Tested) Prusa i3 MK3 LCD_PSU Mod_Cover_Switch v1.stl (New, Not Tested) The cover can be fastened with M3x10 screws...

I use my Prusa i3 MK3 on a Ikea Lack Table Enclosure and the PSU is mounted to the rear left Leg of the lower Lack Table. Anyway i want to keep the PSU as cool as possible. I use a 40mm 24V Fan so it can be wired directly to the PSU. Please don't do...

A simple solution for the PSU cables being too short for the Prusa i3 MK3 Ikea Lack Enclosure design. This is just a simple cable guide to route the cables from below directly to the EINSY board. Instructions: Position your Prusa i3 MK3 in its...

This is a PSU cover for Prusa i3 MK3 (and MK3S) that has the power input on the back. I recommend that you completely remove the PSU from your printer (including all the wires!) before attempting to install this cover. I did it with all the wires...

------- This is a quick adapter for a MeanWell 350W PSU to fit the Prusa i3 mk3. Four parts: - the main brace - the PSU holder - bottom plate for the PSU holder - small spacer disk to place between the top of the PSU and the brace This is designed...

This is a PSU cover for Prusa i3 MK3 (and MK3S) that has the power input on the back. I recommend that you completely remove the PSU from your printer (including all the wires!) before attempting to install this cover. I did it with all the wires...

A small table I made when I moved the PSU outside the printer enclosure. Use M3 screws and nuts to secure the PSU to the table. The files also include a wall mount for the table and a version of the table without the holes. The painting was done with...

An upgraded version of EvoutG's brace: Now using M4 screws on the Y axis leaving the M3 T-Nuts in their old position, to upgrade it without needing to disassemble the printer. ... * Beefed up mounting point on the Z-Axis screw * Space for M4...

The Original Design's supplied STL files for the socket had a wrongly placed top socket holes, as found by me and multiple other commenters. UPDATE 12/5/2021: Original design seems to have disappeared off thingiverse, I think its new home is at...

PSU holder / cover for Prusa i3 MK3 printer to mount the PSU on top or bottom of the enclosure on it's side.

I'm going to have the PSU cables go through the tabletop after someone suggesting it on the Prusa forum but this will also work with the original cable port in the printed corner. In that case you can mount this bracket on the other side of the PSU...

A brace to reinforce your Mk3's frame in case you want to move the PSU elsewhere (e.g. outside enclosure). Other designs seemed not sturdy enough for my taste, so I designed this one with stability in all directions in mind, while saving a good...

So I created a box under the power supply directly attached to the frame of the i3. Since the whole thing should be controllable by touch with a 7" display and should still fit next to my MMU2, I will soon publish a mount for display and the pi...

Printed with the 120mm fan side facing down on the print bed. ...No supports were necessary in my case.

-This uses the mk3 plug/fuseholder, switch, powerpanic board, and all hardware from the Prusa psi cover. Nothing else is needed to convert a mk3 to the Mean Well LRS 350-24. The MeanWell fan is louder than I like, so I replaced it with...

Essentially, this is the same as [this PSU holder](https://www.thingiverse.com/thing:3195906). The only difference is that I made a bigger hole for the power switch. ... **The hole is 30x21mm big.**

This is a PSU cover for the Meanwell/typical Chinese PSU for Prusa i3 MK2 and MK3.. My aim was to keep the appearance of the original Prusa part and for it to fit well and I think I managed that quite well. There are two versions. One for the...

A simple frame to hold a 12V fan onto the Prusa I3 MK3 power supply (not tested on MK1, MK2,,but tell me if it's work on your psu frame..) The input of the controller must be connect directly to the 12v power supply output Here is the fan i use and...

Updated 31 January : Added Manual "how to program the regulator" RELEASED Here is the temperature controlled version ...An old working power supply is a power supply that has been well cooled throughout its life... Hi ! A simple frame to hold a 12V...

The Original Design's supplied STL files for the socket had a wrongly placed top socket holes, as found by me and multiple other commenters. I took a look at the .STEP file and the socket was in the right place, so I suspect something happened...

This design does just that, providing a low profile mounting solution for the black PSU from the MK3 series.There are four holes to secure the PSU, and five holes to mount the bracket itself. This has been sturdy enough for me, and I move the...