pull copter 3d models

Pull Copter Finger Ring that was designed to be printed on the tiny Fulcrum Minibot 3d printer with a buildvolume of only 7.5x7x7cm. The Pull Copter is assembled using M2x8 Hex Cap screws  Projectvideo:https://youtu.be/Ul6tzKezKa0 Subscribe or follow...

... with a buildvolume of only 7.5x7x7cm. ... The Pull Copter is assembled using M2x8 Hex Cap screws Projectvideo: https://youtu.be/Ul6tzKezKa0 Subscribe or follow me on Instagram: https://www.instagram.com/agepbiz/ Twitter: https://twitter.com/agepbiz

Pull Copter Finger Ring that was designed to be printed on the tiny Fulcrum Minibot 3d printer with a buildvolume of only 7.5x7x7cm Projectvideo:https://youtu.be/Ul6tzKezKa0 Assembled using M2x8 Hex Cap screws Subscribe or follow me on...

I had no M2 screws so I created this snap in handle and while at it I slightly modified the keyGet the other parts from the original project.

This Pull copter is especially designed for using inside the House to play with your cat.It is made out of 9 printed parts and a standard aluminium rail with a diameter of 16,3 mm and a height of 69 mm and a M3 Screw with 30 mm length.When printing...

Pull Copter Finger RingProjectvideo:https://youtu.be/Ul6tzKezKa0Assembled using M2x8 Hex Cap screws.edit 03.07.22 - added longer pull keysSubscribe or follow me onInstagram:https://www.instagram.com/agepbiz/Twitter:https://twitter.com/agepbiz3D...

There are a few pull copters rings around now. This one is print in place, which means, you don't have to assemble the gearbox (The other parts have to be separate, obviously). Just use a pair of pliers after printing to carefully loosen the gear, as...

Tirez sur l'anneau et faites rêver les enfantsModèle de Agepbiz modifié :clé plus grande ==> 130mmx3 vis CHC M3x8, cela fonctionne également avec de la gluel'anneau devient une poignéePull the ring and make the children dreamModified Agepbiz...

Pull copter ring rotated 90 degrees.&nbsp;Not tested. ...If you print it, please post a make ;)</i></p>

2× and 3× longer copter key for better fly ;-) Remix of https://www.prusaprinters.org/cs/prints/35410-pull-copter-finger-ring Enjoy it!

This is a remix of agepbiz's Pull Copter Finger Ring.No assembly required! (Although you do need to remove some support material.)I merged the ring and frame parts together, removed the no-longer-necessary screw holes, and changed some overhangs to...

The propeller here has a number of improvements over the usual pull-copter propeller: * The blades are accurately twisted for constant pitch along the length of the blade. * The blade transitions through three NACA airfoil shapes from the root to...

The propeller here has a number of improvements over the usual pull-copter propeller:The blades are accurately twisted for constant pitch along the length of the blade.The blade transitions through three NACA airfoil shapes from the root to the tip:...

The propeller here has a number of improvements over the usual pull-copter propeller:The blades are accurately twisted for constant pitch along the length of the blade.The blade transitions through three NACA airfoil shapes from the root to the tip:...

I designed this stronger key after my grandson broke the original pull-o-copter key. I've only printed with PETG and relatively high infill. ... orient on flat side, supports are not needed

Pull-O-Copter in action (tiny video): https://youtu.be/WDU0ompqszc You'll need 2 m3 screws, length: 10-13mm Update1: The rotor now comes in 2 sizes, 100mm and 150mm (150mm doesn't provide much lift yet, will update soon). Enjoy! Update2: ...

Here is a simple toy that took me back to my childhood. I wanted it to print as fast as I could so that I could play with it as soon as I could! The handle took the longest time to print, so I decided to figure out a way around it. Enter the WATER...

Note I've only included modified parts and the originals can be taken from the linked sources. ... Note: the handle orientation should be flipped when slicing 180 from that in the file

The longer Pulling Rod make any propeller fly higher (compared to original pull rod) Some more infos : Original pull rod is 240mm long and has 73 teeth Modified one is about 320mm long and has 100 teeth ! ) This gives 37% more teeth Of course,...

This drop should be located between the axis and the gear.It is not necessary but I lubricated all mechanical pieces with some paraffin wax. A drop of Oil will do the job too but may be messy.Put the pulling rod in the place marked by the arrows. So...

Set of rotors for (and compatible with) funny 3D printed toy Pull Copter Finger Ring.Basically it's two sets of remixed rotors:First set is a remix of original rotor from Pull Copter Finger Ring model from Agepbiz into two sizes (original) 65 mm and...

I only changed two files, so you'll need to get the rest from agepbiz's pull copter finger ring model.&nbsp;Flipped orientation of the M2 screw so that the threads are in contact with more plastic to reduce stripped threads.&nbsp;&nbsp;I'm also...

... holder to the gearbox with super-glue. It prints 3 alignment pegs and holes to align the holder with the gear-box.&nbsp;I printed the rotor and key in PETG and the rest of the items in PLA with variable profile.The pull copter flies very nicely :-)

... An even longer key, 1.5x the size **Usage:** Print and assemble (using M3x8 screws). Use some **PTFE or similar spray** if it doesn't work smoothly. https://www.prusaprinters.org/prints/36141-improved-3d-pull-copter-finger-ring-m3-screw-versi

Improved version of the 3D Pull Copter Finger Ring with a different rotor design. NOTE: Models not compatible with original design Features: Improved rotor design (bigger and angled differently) Somewhat longer key for easier use Uses M3 screws...

These are optional parts for the [Pull-O-Copter by Toastify](https://www.thingiverse.com/thing:2428046). (Thank you Toastify!) * 3-bladed 125mm diameter propeller * 5-bladed 125mm diameter propeller Blade sections: * NACA 2424 @ the...

These are optional parts for the Pull-O-Copter by Toastify. <a href="https://www.thingiverse.com/thing:2428046">https://www.thingiverse.com/thing:2428046</a><br/> (Thank you Toastify!)</p> <p>Parts:</p> <ul> <li>3-bladed 150mm diameter propeller</li>...

There was no separate hook handle in the original, and my slicer (AnkerMake) doesn't make it easy to separate stl files, so I put this up for anyone in my situation.

I separated out the hooked and looped short pull rods for https://www.thingiverse.com/thing:5413706 so that others could use them as needed. My daughter broke one of the pull rods and wanted a replacement. ...The hooked and looped ones were her...

Small Update & Parts explanation: Added a 200 mm Pulling Rod for smaller Printbeds. (Original is 240mm) Added a 4 bladed Prop. Will be a little more robust but the 3 bladed one works better. Update 06.07.2022 Added a new (hopefully)...