pythagorean cup 3d print

Having to make several 10+ hour prints to tune the shape resulted in some useless models and destroying those by hand took a lot of force, so I know this is strong and will hold up on very bumpy roads. See my other versions of this water bottle...

1x Brand NEW Warlock Subclass: Dragon Patron 1x Full size A2 printable map of Greypeak 1x Full size A2 printable map of the city of Vanlund 6x original Battle Maps, including an enormous dungeon (for use printed or digitally) 10x Original Statblocks...

Includes an alternative top with a spot to mount a 30mmX30mmX8mm fan such as these: https://amazon.com/gp/product/B07QJ4MS2L Instructions I printed mine in PLA, 0.3mm layer height, no support. Files for two "Top" pieces are provided, the standard and...

If you use Marlin, you could set in Configuration.h: ``` #define X_MIN_POS -15 #define Y_MIN_POS -15 ``` Print with ABS or with any rigid plastic which works in your temperature range. Take into account that the mount contacts the stepper motor which...

This star ornament was printed in white PLA at 200C and the printbed heated to 65C. You might also be interested in my <a href="https://www.thingiverse.com/thing:3247849">Star 1, </a><a href="https://www.thingiverse.com/thing:3247833">Star 3</a>...

I strongly recommend printing Mpooh's fuse holder and wiring in an automotive fuse in series with the battery. The battery probably has protection circuitry, but who knows how much power this battery can supply before protection shuts it down. I use...

I have not had a chance to print this yet, as my printer is offline. Update Corrected the spacing of everything and added features on the underside to be more consistent with the construction block system I am trying to be compatible with. Added...

Gather materials (have the plywood and tabs laser cut (DXF) and print out the NACA Ducts). 2. Bend and form the landing gear (do this first!). I think I used .64" wire (up to 2mm will fit, but that's a tad overkill, I think). 3. Take the pod pieces...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable retainer...

Instructions: Print the cover/faceplate, body, and screw jig.. in the body, insert the 2x, m3, heat set inserts, in the 2 ears from the inside of the body, so the screws would be trying to pull the insert all the way through, instead of back...

... secured on top, use the holes and pegs versions! For mounting the legs to the screen, use 2 x M4x20 screws and nuts. I mounted the Pi with 4 x M2x10 screws. #See pictures for usage! #Thank you, like, share, and enjoy! It's printing now...

Mini blow darts 16g or 20g threaded CO2 canisters CO2 Tire Inflator M4 screws M3 Screws M2 Screws 7/32" x 11/16" Compression spring Small Rubber bands Printed Parts List ShellCylinder RearFrame BarrelFrame BarrelShroudExtender (Optional)...

HotBed = Factory Item I would recommend placing a silicone thermal pad and a sheet of glass on the heat bed for better prints. Power Switch = Standard PC fused and lighted This upgrade allows you to actually turn off the printer with a switch...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver - ...

Plus tiny stool.  - Cupboard with microscope top option All the parts are pre-supported for SLA resin printing! This set works together with the Medical Bay set (the table, drawer & cupboard top options are interchangeable - there is also some...

The STL file itself prints flat and then will need to be bent with a slight angle in the stem. This can be accomplished by running the stem under hot water or dipping it in a bowl of hot water to soften it a bit, and then using a pair of needle...

Optional spacers can be printed to ensure proper spacing between GLCD circuit boards as mounting screws are tightened. An optional rear panel cover is provided for use with the GLCD case. The case has holes for up to M3 hardware, but it's intended...

I also have a light-sensitive resistor on it and plan to add a sensor at the rear and one facing down to prevent the robot from driving off cliffs.\r\nI've got plans to be able to extend the length of the track assembly by adding a third cog, but I...

No supports are needed to print this throttle! The intent of this design is to show how easy it is to make your own throttle and buttons control. STL and FreeCAD files provided. The bearings are very inexpensive and result in a robust and...

I will need a spacer, either printed or metal, between the pulley wheel and the top bearing of this mount block. I have to figure out what height of spacer will put the pulley wheel at the same height as the pulley on the stepper motor using KIdz's...

(To print with the installation of a filling enclosed areas) About the hero Gabriel, 21 years old Originally from the town of Davenport A stout young man of small stature, dressed in simple but elegant clothes(or so he thinks) Characteristics Wizard...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

Blocks with other angles can easily be modeled and printed if needed. It should be noted that the complementary angle to the one shown on the gauge can be mitered by placing the material against the other face of the miter gauge. The shooting...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: pinNumberY = 35 pinNumberX = 13 GEAR GENERATION ON Music Cylinder Teeth Number = 24 Minimum Diameter = 1.5 inches Gap Between Gears = 1 inch...

It's a simple print but does require your printer be well tuned. I had to remake this idea about 6 times before finding something that would fit right and not touch the heat block. You will need to remove the H2 from the printer in order to...

The system interacts with an on-device embedded webserver, and I've used the same prints for multiple brands of blinds.\r\n\r\nCheck out the pictures and animations showing how it all fits together.\r\n\r\nI previously had two code bases for MQTT and...

In a closed case its unneccessary to use bulky plugs everywhere, so i directly soldered the power-in-usb-jack to a dc-jack; to one of the usb-ports i soldered an USB-cable to be able to re-route the USB-DAC to the tray. printed in black PLA, ~50mm/s...

The 18 to 22 pipe fitting could be removed This plate could then be copper plated with this technics : https://www.thingiverse.com/thing:1661301 If you have any design to share I would be glad to offer at least the binary codes of the ESP32 and the...

It supports several configurations based on whether you want an insert to go into the “empty” insert hex holes, or full insert with or without the “face” decoration (and also allowing a flat bottom for easier horizontal printing).If you wish to make...

I've tried increasing the print speed to 150%, no layer offset !, there's probably more to do. For assembly: I bought my motors online (MKS SERVO42C NEMA17), they were already pre-assembled and calibrated. So they could be used immediately. To...