qidi tech x max 3d models

It also fits stock printers of course.It should also fit QIDI X-Plus and I-Mate (and I-Mate S) but I've only tested it on my X-Max.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress and Banggood. Shipping takes...

Made this spool holder extension to be able to mount large spools on the stock spool holder of my X-Plus (i think this should also work with the X-Max). Insert the extensions on top of the fully extended spool holder rods and then place the spool on...

About This is a support bracket for the Qidi X-Plus and X-Max ribbon cable, it attaches to the top extruder cover. Without support, the cable dips down when it gets extended, causing unnecessary stress on the cable as well as it getting greasy from...

Filament spool holder and filament guide arm for the Qidi X-Max... I'm a fan of the X-Max printer, but the supplied spool holder rod and feed mechanisms leave something to be desired. I wasn't able to find anything online as a replacement quite to...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.</p><p><strong>BOM - Bill of materials</strong></p><p>You...

About This is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. To use, print the two parts. Cut a piece of sponge and place it inside the...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

Bob Martin in the Qidi 3D FB group owns an X-Max and says it fits his also, otherwise, there is another pi-cam mount you may want to check out here if you think this one is in the way too much: https://www.thingiverse.com/thing:4347548 I'm using the...

3:1 BMG Extruder) // New PID values // tested code in Octoprint M303 E0 S220 C10; // returned: bias:105 d:105 Ku: 37.659279 Tu:21.200001 // returned: Kp: 22.595568 Ki:2.131657 Kd:59.878258 // Send updated PID M301 P22.595568 I2.131657 D59.878258; //...

I purchased a dial indicator to level my qidi x-plus more easyly and precisely. When I tried the holder from fdunn59 (https://www.thingiverse.com/thing:4633291) I had the problem, that material from the neodym magnets rest on the linear rails and it...

I increased the size of the cable access because my cable would not fit. ...Guessing Qidi may have changed the cable size.

I broke my spool holder so made another and it fits the Qidi perfectlyAlso fits all standard rolls of filament. I used Tree Supports and printed in PLA

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

The files added are: external-rod-holder-left-tall-1.0.stl external-rod-holder-right-tall-1.0.stl About The Adjustable Spool Holder for QIDI X-Plus and X-Max works with most filament spools up to 1 Kg. It uses common 608 roller bearings (search for...

About This is an advanced Extruder Cover for the QIDI X-Plus and X-Max. The original cover didn't have much space for a larger fan (although a 40 mm fan just about fits) and was lacking a few other features. The cover has the following features:...

I just recently converted my Qidi X-Plus over to a Lerdge K setup like my X-Pro. I wanted to keep the FFC ribbon cable setup but add the auto leveling functionality now available to me. I tinkered with several addon mounts but none of them seemed...

Made this spool holder extension to be able to mount large spools on the stock spool holder of my X-Plus (i think this should also work with the X-Max). Insert the extensions on top of the fully extended spool holder rods and then place the spool...

Required purchase - 40mm x 10mm 24v fan. Some sanding of carriage material also required in order for lower duct scoop to fit between extruder and carriage housing. Quick print. Recommend filament that withstands high temps, Nylon, ASA or...

I bought mine here: https://www.amazon.com/gp/product/B07JG7DS7V/ If they are out of stock the specs are: Inner thread size M3 x 0.5 Outer thread size M5 x 0.5 Length 6mm This is primarily for people who would want to print these parts out in resin...

null

I modified the design from https://www.thingiverse.com/thing:3598723 by changing the pipe in a way that allows the original plastic pipe to fit into it smoothly.\r\nThe smaller inner radius ensures the filament can't be pulled back towards the spool,...

Remix of eSun Box Bracket for Qidi X-Max by SupramanGT42. Remixed into multi-piece design for easier printing. ... Some assembly Required.

Modified Part Cooling plate for Qidi X-Plus and X-Max BMG V6-Extruder Mod by Chad Wills. Make sure to print with a nozzle not bigger than 0,4mm due to thin wall sections. Do not use 100% fan speed for bridging sectionswhen using this...

This is to allow one to install the Octopus Pro motherboard into the Qidi-Tech X-Max chassis. Has an offset to allow the wifi antenna to protrude outside of the metal under carriage, potentially giving you better wifi performance. Also drops...

A small click-in mount makes your C100 from Tapo fitting into your Qidi X-Max without disrupting anything. I've tested it while printing with 100°C bed and enclosure for hours. No problem. ...If you make it your own please show me,

I made this fan duct / register box for the QiDI X-Max printer to use in my review video: https://youtu.be/teKYmFW6g6A I am not going to drill holes to fix it, just use double-sided tape to seal the egdes.

Tweaked the awesome "QIDI X-Max Modular Tool Holder" Changes (to wide) * Added bottom hanging caliper holder * Glue stick nub to mount on top * USB holders * Micro SD slots * Larger pencil holes * Allen key holes near end I've included step files and...

I made a small camera mount for the qidi x-max to take up a c100 by tapo. I tried it out several times with prints ober 14h, enclosure and 100°C bed, and the camera had no problems with that. if you make it your own please show me. ...have fun.

The Carriage Mounted Dial Indicator Holder for the Qidi X-Max is an excellent design by humebeam. It can be used with the original carriage by Qidi. Only the cover, ribbon cable, two screws for the extruder and the extruder itself have to be...

Since I don't want to feed the Qidi X-Max 3 with filament from the back or the left side, but want to use the run out sensor, I have created a small L-shaped bracket to bring the sensor to the side of the printer so that I can load it from the...