qidi tech x one manual 3d models

THIS IS A REMIX I've modified the files to match the Qidi X-pro perfectly. They should work great and still allow for the top to be securely attached. I've only tested two of them on the right side, so I'm unsure if all four bins will fit with the...

Designed for the Qidi X-Pro original. Remixed to make the heights work with the original hotends instead on the high temp ones which are shorter. Scale the 8mm shroud to 99% as it allows a better fit in the duct. Needs 30mm M3 bolts whereas...

I wanted to add a simple microswitch filament sensor to my Qidi Tech X-One2. The idea for this came from: https://all3dp.com/2/ender-3-filament-sensor-runout/ There are designs on Thingiverse, but their suitability is dependent on getting a...

I wanted to add a simple microswitch filament sensor to my Qidi Tech X-One2. The idea for this came from: https://all3dp.com/2/ender-3-filament-sensor-runout/ There are designs on Thingiverse, but their suitability is dependent on getting a...

Spool holder for the Qidi X-Plus uses factory spool holder cradles to secure mounts, working in either direction with tube on rear top or over machine top with cover on. Spool width is approximately 3-1/2 inches, placing a standard spool about 5...

It's an alternative Spoolholder for the Qidi X-Max3 to get rid of the backward loading. Still WIP, will add bowden support but works at the moment :) The holder will snap in the hole where you can adjust the belt tension. Use the screws of the...

... popular 200g Amolen model. ...It perfectly complements the stock spool holder on the Qidi X-smart printer. ... The specifications of this spacer are as follows: a diameter of 70mm and a height of 34.5mm, with a central hole measuring 55mm in diameter.

This puts a standard spool hanging about 5 inches behind the machine. This was remixed from another remix holder made for another machine I believe the original was 1832235 just searching back. You will need: Both mount sides(they are mirrored). 4 of...

Therefore, I have created a Spoolbox Support for the X-Max and compatible QIDI printers.You can use this support while the strut is lowered or up in place. If you extend the strut, you can use a small bracket to keep the support horizontally. The...

Back Plate for Qidi X-Max 3.Allows replacemenr of noisy motherboard fan by a quieter and bigger one 60x25.Material : PLAQuality : standard, 0.2 layer heightInfill : 15 %Support : snug for the left partNo Brim, Mickey’s ears to prevent warpingLeft and...

I remixed this cooling duct to fit the Qidi Technology X-Max because there are not very many options for upgraded cooling ducts. I recommend printing it in the orientation I have it placed in. Just use 85 degree supports "everywhere" and it will only...

I remixed this cooling duct to fit the Qidi Technology X-Max because there are not very many options for upgraded cooling ducts. I recommend printing it in the orientation I have it placed in. Just use 85 degree supports "everywhere" and it will only...

My design for better Qidi X-max feet. The original rubber feet are cheap and tore soon after getting the printer. These ones have a larger surface area for better weight distribution and lift the printer up allowing for better airflow to the board. I...

Spool Holder for Qidi X-Plus Machine. This design utilizes factory spool holder cradles to securely fasten the mounts, allowing it to be used in either direction - either by attaching the tube to the rear top or positioning it over the machine's top...

... 52mm - not fully circular to provide some grip. Two additional adapters were added, one with an increased diameter of 95mm (suitable for 2Kg spools) and the other with a higher width of 90mm. ...This second adapter is used for wall mounting.

I discovered a sharp edge on my Qidi x-pro cover and the feeder tubes were rubbing against it, causing wear. To round off that corner, I created this part. It needs to be rotated in place. I printed the rounded section down (no supports required) and...

A filament guide for the Qidi X-Plus (X-Max?) , which replaces the original and can also be used with the hood closed. For mounting, the filament guide is simply pushed from behind into the original holder. Through the small hole at the front end,...

They must be so accurate that the fittings push down on the pipes so much that they are tight, but do not bend.So it is here that "Distance Meter PTFE for Tube Qidi X-MAX Hot End" comes into the picture, to get the pipe length exactly correct.To...

A replacement top cover for the Qidi X-Max that features - much better thermal insulation - less stress on the filament on its way from the port to the hotend - a thermometer/hygrometer Bill of Materials ----------------- - 15x M3 threaded inserts -...

But then one day i looked and saw that the output side was warping and hanging a little lower than the bottom plane. So I printed another one and I removed the old one. I then noticed that it had a sharp dent from the top side which pushed the bottom...

IMPORTANT: This design is based on Hercules - QIDI X-Max Carriage done by member humebeam. Not sure if this counts as an actual remix since most of the original design has changed and the complete carriage remodeled. <i>All the firmware instructions...

fit's exactly to this cam and the qidi-Xplus only snap in and use a long flat cable and your ready for surveillance your print. ... https://www.amazon.de/MakerHawk-Raspberry-Nachtsicht-Kamera-einstellbar-Fokus-Modul-Himbeer-pi/dp/B071718FDK

The tool remains open at one end, allowing for easy insertion through the T-Piece hole into a rebreather counterlung to hold the backside of the valve securely while unscrewing the front. This is version 2, which boasts several improvements over the...

The biggest difference is I have a X-Plus vs the X-Max and while many things are the same there are some differences I found over this adventure. the next difference is I was using the stock carriage for now cause I can't decide which replacement I...

This is a basic, minimalist x-axis stop designed for the QIDI X-One2 and X-One printers. To use it, you'll need one if you decide to take off the cover that protects the print head. ...I opted out of mine to get better access to the extruder and gain...

The original fan mount on the left side takes a bit of effort to install, but it manages to accommodate the X-One2 fan with some minor adjustments. ...Currently, the extruder cooling fan is restricted to functioning properly with just a single bolt in...

I needed a way to attach my Wyze Wi-Fi camera to something sturdy, so I found this mount that fits perfectly on the front of the X-Plus printer. It lets me secure the camera using either the adhesive strip that comes with the Wyze cam or by screwing...

This is a tool box that fits into the carry handle of the X-Max printer. Partially print the handle insert to gauge size and use your slicers scaling to decrease or increase as needed for both parts. Its a press fit and will depend on the material...

This is a tool box that fits perfectly into the carry handle of the X-Max printer. To ensure a snug fit, partially print the handle insert to gauge its size and then use your slicer's scaling feature to adjust both parts as needed. The tool box will...

To complete the assembly, you will need to print the following components: * One left side bracket V2 * One right side bracket V2 * Four pivots (it's recommended to print these with support and 100% infill) * Four ball bearing cages (print with...