qidi x max 3d printer

It also fits stock printers of course.It should also fit QIDI X-Plus and I-Mate (and I-Mate S) but I've only tested it on my X-Max.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress and Banggood. Shipping takes...

**MOVED TO PRUSA:** https://www.prusaprinters.org/prints/155501-qidi-x-max-x-plus-internal-filament-guide-v2 This internal filament guide set works with X-Max and possibly the X-Plus. It replaces the simple OEM vertical guide with a 4mm ID X 6mm O.D....

It is a phone mount for the Qidi tech X-max and X-plus. You would need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

It is a phone mount for the Qidi tech X-max and X-plus. IMPORTANT: You will need to use attached custom start and end g-codes in Cura (or whichever software that allows them). Otherwise the extruder will hit the mount during initial priming. ...

Updated June 2022This carriage fits the Qidi X-Max (X-Plus) where the bearings are 29mm L, 19mm O.D., 10mm I.D.The stock Qidi X-Max carriage it is a pain in the you know what to switch between the low temp to the high temp extruders.This design moves...

Thanks :)https://www.paypal.me/humebeamengineeringAboutThis is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM -...

This is a Bowden Tube Connector for the QIDI X-Plus and X-Max extruder covers. Just remove the screw from the top cover, place the connector and screw it in place with a 20 mm M3 screw. It is compatible with 6.0 mm PTFE tube, same dimension as the...

It also touches the X-axis belt.To install simply push in the tabs through the holes on the left side of the extruder cover then push down to secure it (use the lower holes) and route the ribbon cable over it.Print SettingsPrinter: QIDI Tech...

Bob Martin in the Qidi 3D FB group owns an X-Max and says it fits his also, otherwise, there is another pi-cam mount you may want to check out here if you think this one is in the way too much: https://www.thingiverse.com/thing:4347548 I'm using the...

This spool holder attaches to the rear of the X-Max printer using two M3-.5 x 16 bolts (and washers) which you can pick up from any hardware store or order online. I'm not certain all X-Max printers have these "mounting" holes, so you should check...

There are four parts: Upper Guide, Lower Guide, Lower Guide Standoff, and PTFE Tube connector for BMG type extruders.The setup uses about 1.5 meters of PTFE Teflon tubing 4mm ID X 6mm OD 1.5:...

This is a recessed cover designed to close the large opening in the Qidi X-Max & X-Plus printer top covers, allowing for filament spools to be accommodated without excessive pressure. Additionally, I created a 30mm to 50mm spool insert that helps...

This is a Hygrometer / Thermometer Holder that snaps onto the rear chamber fan cover of the QIDI X-Max and X-Plus. It was requested by one my followers. It might fit other printers as well.BOM - Bill of materialsYou need a small round hygrometer...

About Gripen is a high flow fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it installed in...

About Draken is a high flow dual channel fan duct for the QIDI Tech X-Max and X-Plus. In order for you to use it, you need the new extruder carriage. I have attached a picture so you can tell if you have the new carriage or not. If you don't have it...

Step file is available if you want to make any changes.Be sure level the bed afterwards.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports:NoResolution: 0.15 mmInfill:30 %Filament: Prusament PC Blend Orange  Notes: I...

After getting frustrated with every adapter and modification I've tried for my Qidi X-Plus, and X-Max, I have tried most of the prints and only found one mod that works (yet motion isn't as smooth as I'd...

Print on it's side with support between the feet (as per diagram in "QIDI X-Plus X-Max Ribbon Cable Bracket by humebeam ") Printed in PLA+, has enough flex. Post-printing, just needs sharp edges smoothed. Note: with any back clip, on the X-PLUS,...

You can use it internally like I have done here or anywhere you like.Next, load the filament in your extruder and you're done.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports: NoResolution: 0.20 mmInfill: 25% Filament:...

3:1 BMG Extruder) // New PID values // tested code in Octoprint M303 E0 S220 C10; // returned: bias:105 d:105 Ku: 37.659279 Tu:21.200001 // returned: Kp: 22.595568 Ki:2.131657 Kd:59.878258 // Send updated PID M301 P22.595568 I2.131657 D59.878258; //...

I purchased the Qidi X-Max in December 2021 and these carriages fit models of this period. The bearings are 29mm L, 19mm O.D., 10mm I.D. Probably fits the X-Plus from the same period, but I cannot confirm this. My system was making unsettling...

To upgrade, you only have to reprint this part, the other parts are unchanged: qidi-xplus-xmax-extruder-fan-duct-404020-part-2-ribbon-cable-holder-1.1.stl About This is an alternative to my QIDI X-Plus X-Max Advanced Extruder Cover:...

Make sure you feed the filament from below the spool through the black filament guide tube.BOM - Bill of Materials2 x 608ZZ roller bearings1 x M3 or M4 screw and bolt (15 mm) (optional, you can use the stock screw and nut)What to printPrint the...

About This is a support bracket for the Qidi X-Plus and X-Max ribbon cable, it attaches to the top extruder cover. Without support, the cable dips down when it gets extended, causing unnecessary stress on the cable as well as it getting greasy from...

About This is an advanced Extruder Cover for the QIDI X-Plus and X-Max. The original cover didn't have much space for a larger fan (although a 40 mm fan just about fits) and was lacking a few other features. The cover has the following features:...

About This is a filament cleaner and backspin preventer for the QIDI X-Plus and X-Max. It was originally designed for one of my other designs but I never included it there. To use, print the two parts. Cut a piece of sponge and place it inside the...

I purchased a dial indicator to level my qidi x-plus more easyly and precisely. When I tried the holder from fdunn59 (https://www.thingiverse.com/thing:4633291) I had the problem, that material from the neodym magnets rest on the linear rails and it...

FOR QIDI TECH X-Plus 3 Implementation: I have designed a filter for air purification during the printing process, which has not yet been tested in action. The filter's volume was chosen to be roughly similar to those used in Bambu printers. The...

I broke my spool holder so made another and it fits the Qidi perfectlyAlso fits all standard rolls of filament. I used Tree Supports and printed in PLA

I increased the size of the cable access because my cable would not fit. ...Guessing Qidi may have changed the cable size.