raise3d n2 plus
43657 3d models found related to raise3d n2 plus.cults3d
This is a model to test the levelness and height of your platform on a Raise3D N2 (Plus) 3D printer. ... http://www.3dwp.nl
thingiverse
This is a model to test the levelness and height of your platform on a Raise3D N2 (Plus) 3D printer. ... http://www.3dwp.nl
thingiverse
quick lid stand L R with I use the holes for elastic and TPU filament feed with the spool out side on the floor use double sided tape to attach ,make sure there is a 5mm gap all the way around the base so the lid clears the bottom of the stands best...
thingiverse
Just got a used Raise3D N2 Plus. Previous owner had swapped to Noctua 40mm x 10mm fans, but still using a slightly modified original mount - which seemed very badly designed as it barely blows on the heatsink heatbreak section. Been having troubles...
thingiverse
This is an air tunnel for the Raise3D N2 / N2 Plus for better cooling of the motion board. Inside is printed with ABS Outside is printed with Polyflex In addition, we also use a piece of activated carbon for air purification. ... www.okm3d.de
thingiverse
Designed to bolt on to the front of a Raise3d N2 series printer. ...Adds a directional cooling duct and more clearance for the tip of the nozzle.
cults3d
This mount let you use the existing extruder fans for controlled cooling of your printing part plus an additional fan (35mm or 40mm) as replacement or extruder cooling. This Version allows you to reach all relevant screws to loosen and tighten the...
thingiverse
This set of risers is intended to raise the printer’s entire top lid to prevent the head from overheating during printing. ...To deal with outgassing from nylon (which I am allergic to), the fan to outside is sufficient to maintain control of airflow up...
thingiverse
measurement gauge mount why did I choose this design: - the mount is really stiff -> really small measurement tolerances related to the mount - it's possible to use the home button for X and Y - you could reach any required position for the...
thingiverse
Easily dismount cam from original support and plug it onto the new one. New support is designed to fit on "cable tower" on top of the printer. ...
thingiverse
Bottom is 300mm and top is 300mm long. So scale accordingly. I will be adding improvements as needed and will add them as I design them. I needed a 2.5kg spool holding solution and this seemed to be the easiest way to do it. I printed this in...
thingiverse
On the original installation instructions the sensor is fixed with tape inside the printer and the filament for the left extruder must be loaded into the right sensor input. With the new holder the sensor is fixed with screws and the filament for...
thingiverse
filament funnel guide for raise3d n2 and n2 plus Use super glue after assembled Print Settings Printer: raise3d n2 and n2 plus Resolution: .15 Infill: 15 percent Notes: funnel facing up on bed including hole on retainer box
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iORKNCcl5Gq
thingiverse
Borring to lost my print because the filament bend a 90° and don't fit inside the head of my raise. So to fix the problem I create a feeder with a lock system on the top screw to lock it. Problem solve. ...;-) I hope this can help you.
thingiverse
Print in ABS Print Settings Printer: Raise3D N2 Plus Rafts: Yes Supports: No Resolution: 0,2 Infill: 20
thingiverse
... N2 Plus Printer Works with Dual Head as well. ...Print Settings Printer: Raise3D N2 Plus Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .2mm Infill: 10% Notes: for best results and durability print with temperature resistant material!
thingiverse
clip permettent de fixer un plateau perforé a la raise 3D pro2 https://www.atome3d.com/products/plateau-perfore-340x330mm-compatible-raise3d-n2-n2-plus?ls=fr-FR
thingiverse
I was having trouble with the Raise3D N2 Plus supplied filament holders in that it seemed to have too much friction at times causing printing errors and nozzle clogs. This seems to have corrected that problem. I am now able to print with other...
thingiverse
Alternate filament runout sensor housing for the Raise3d N2/Plus. The original one included hides the LEDs and the logo is not displayed. With my design, the bottom part can be removed. Parts I Used: Threaded inserts 2- M3 4mmX5mm 2- M4...
thingiverse
... own a N2 Plus you will need this. ...Print Settings Printer: Raise3D N2 Plus Rafts: Yes Supports: No Resolution: 250 Notes: Resolution doesnt matter here. This is a test for Ringing when model is tall. Select Vase mode when printing. ...1 shell 250um
thingiverse
This is a combination heat shield and fan mount for the Raise3D N2/N2 Plus. This version only works with the V2 head. This is a remix of the excellent front fan mount by Sylus:http://www.thingiverse.com/thing:2102446 I got tired of having to remove...
thingiverse
... shorter shaft version (65mm) for the Microcenter Inland brand spools. ... I believe eSUN and many other brands use the same spool configuration. Print Settings Printer: Raise3D N2+ Rafts: Doesn't Matter Supports: No Resolution: 300 microns Infill: 30%
prusaprinters
This thing will be discussed in detail on the 3D Printing Today Podcast: threedprintingtoday.libsyn.com or search the iTunes music store or stitcher radio for "3D Printing Today" This thing is a modification of the Raise3D N2 and N2+ bed. The bed as...
thingiverse
This thing will be discussed in detail on the 3D Printing Today Podcast: threedprintingtoday.libsyn.com or search the iTunes music store or stitcher radio for "3D Printing Today" This thing is a modification of the Raise3D N2 and N2+ bed. The bed as...
thingiverse
improved air intake for the electronics of Raise3d N2 Set scaling to 1000%
thingiverse
Modification of my desktop spool holder to fit inside the Raise3D N2 printer. ...
thingiverse
This is a smaller spool holder for the Raise3D N2 printer. ... This is designed similar to the factory holders for 1" diameter spools.
thingiverse
This is an Indicator Holder for a Raise3D N2 or N2 plus. It allows for indication at nozzle location for 100% of print surface. NOTE: be careful and max travel in the X Axis, holder will hit Pillow blocks! Otherwise works great! Enjoy. I have...
thingiverse
... default. Print Settings Printer: Raise3D N2+ Rafts: No Supports: Yes Infill: 60% Notes: You may need a raft if you see any corner lifting. ... I didn't need to scale the object at all but you may need to make adjustments if using other materials.