rasberry pi 2 3d models

**Features:** * I've included all my original source files in fusion360 format * I've included all individual parts in STL format * Low profile self-contained little terminal using a full sized Rapsberry Pi 2 or 3 board **Considerations:** *...

When Microsoft announced that Windows 10 would be arriving on the Raspberry Pi 2 in 2015 I became extremely excited at the possibilities that this would bring the maker community. To celebrate I wanted to design a case for the Pi 2 that incorporated...

This housing is designed primarily to work with:https://www.printables.com/model/273361-spider-steppers-aka-28byj-48-stepper-to-12-pvc-pipIt holds 4x 28byj-48 stepper driver boards, and a Pico in a housing that clips to 1/2 inch PVC pipe. ... You...

You'll need additional parts: a 5x7 cm perfboard (i prefer single-side pertinax because one side without copper is good for creating wire bridges) with a mounting hole spacing of 40x64 mm a socket for a 12 volts plug / barrel jack, usually 5.1 mm Ø...

Just a simple mount for my Raspberry Pi Zero 2 W on my Ender 3 Pro! It fit under the screen by sliding the case on the v-slots extrusion. The case fits nicely and does not need hardware to be held in place. However, the case is 2 parts to allow...

Just a simple mount for my Raspberry Pi Zero 2 W on my Ender 3 Pro!It fit under the screen by sliding the case on the v-slots extrusion. The case fits nicely and does not need hardware to be held in place.However, the case is 2 parts to allow easier...

When Microsoft revealed its plans to bring Windows 10 to the Raspberry Pi 2 in 2015, I was bursting with excitement about the limitless possibilities this move would unleash on the maker community. To kick off my enthusiasm, I set out to design a...

Parts List: * A Raspberry Pi 2 Model B * A 3mm LED in your favorite color * A resistor matching the type of LED (LED with 10mA connected to 5V, resistor value around 330 Ohms) * A cable with a connector to connect the LED and the resistor to the pin...

A versatile two-piece case for the Raspberry Pi, designed to fit seamlessly with B, B+, and 2 models. All you need is some M2.5 bolts and spacers to assemble this robust enclosure. As part of my "Switch" project, I conceptualized a modular camera...

This is a bracket to secure a Raspberry Pi 2 case to the side of a Duplicator i3 Plus. Designed with dimensions matching those of the Canakit case, it should fit most standard Pi cases with ease. The Canakit case measures precisely 62.7mm x 93.7mm x...

This is my initial design of a raspberry pi case that fits both the 2 and 3 versions of the pi. The only variation is in the placement of lights, but even when printed using PLA, this difference becomes apparent anyway. This is a sliding model,...

Check out all of my other designs under my profile at Thingiverse: https://www.thingiverse.com/The_Craft_Dude/designs This is a Raspberry Pi case designed specifically for use with the Pi Zero and Zero W, scaling down the Trash can Mac Pro's design...

Just thought I'd release my Raspberry Pi 5 SSD 2.5 case for everyone to enjoy as I haven't seen any yet, still keeps the raspberry pi cool during heavy loads and overclocking! Fits with or without the active cooler. Print the bottom half standing up...

This is a remix of [A_Great_Future_in_Plastic's Pi Camera 2.1 Mount](https://www.thingiverse.com/thing:1568750) to give a nice low profile corner view on an Ender 5 and probably other 2020 corner framed printers. Just whipped it up in TinkerCad so...

If it breaks I'll make a reinforced version :) EDIT: Just ordered some PETG, will probably reprint it in PETG Case fits both Pi Zero 1 and 2. I assume the bracket fits both the original Ender 3, and V2 but this is untested. ... Printed case with...

Mounting bracket that fits any of Orange Pi Lite / Orange Pi Lite 2 to mount on Ender 3 Inside there is a place designated for a 3A DC/DC converter (https://aliexpi.com/CLjQ), use doublesided tape to attach it Screws required 4pcs M3x10 DIN912 + 4pcs...

These premium cases are designed to give your Raspberry Pi a sleek and iconic look. But be aware, they're only compatible with the B+, 2, and 3 models for now. If you're not sure what model you have, no worries - we've got you covered. Simply run...

This thing was inspired by https://www.thingiverse.com/thing:2463117 and makes use of this camera case: https://www.thingiverse.com/thing:2265949 While podearroz mount works great for the Pi-Zero, the Raspberry Pi 2/3 uses a wider camera cable. So I...

Raspberry Pi Zero 2 W and Octoprint This case snaps together around a RaspberryPi Zero,Pi Zero W, orPi Zero W 2 and stays closed while allowing heat dissipation and port access. And this is a perfect case and mounting bracket for anyone who wants to...

This is a v slot mount for the Pi Zero 2 case found here: https://www.thingiverse.com/thing:1167846 May need to print with a raft or brim to prevent warping on the mount overhanging support arm. Should work for all Ender 3 variants. I have only...

This is a mount for the Biqu BX Raspberry PI zero 2 W. These are the parts that are needed. CableCreation Micro USB to Micro USB OTG Cable https://www.amazon.com/dp/B01M5GZ3N0?psc=1&ref=ppx_yo2_dt_b_product_details VCE 2-Pack HDMI Mini Adapter...

To complete this project, you'll need the following additional parts: * A 5x7 cm perfboard (I prefer single-side pertinax because one side without copper is ideal for creating wire bridges) with a mounting hole spacing of 40x64 mm * A socket for a...

Bookends for Raspberry Pi cluster, plus remixed support for 3 boards. Category: Electronics

This Is A Container Featuring LR6 Compatibility With Raspberry Pi Zero Boards

I just remixed both designs to be able to mount my PI Zero2 on my printer

Raspberry Pi cluster bookends, featuring a hybrid approach that seamlessly integrates three different boards.

My Latest Case Design for the Raspberry Pi 2 or 3. I wanted a design that would look more suitable for a living room media center streamer. I tried out a few designs in wood filament, stained them, and clear coated them. Obviously, wireless...

I wanted to attach my Raspberry Pi and Raspberry Pi Touchscreen to my Ormerod 2. I envisioned two main goals: controlling the printer with the touch screen, and having a camera watch the print so I could monitor it remotely. To achieve this, I...

I made mount points for The BTT SKR 2 The Raspberry Pi 3 The xl4015 buck converter The MOSFET HA210NO6 After printing, I used JB Weld epoxy to secure both sides together, For the lids, I printed it with vents but glued a screen in to keep stuff from...

Mounting hardware ([All came in this kit](https://www.amazon.com/gp/product/B015A34BUQ/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1)): - To replace the toolhead screws - 4 M2x6 - For the toolhead mount horizontal arm - 1 M2x10 screw - 1 M2 nut...