rc airplane skis 3d models
38509 3d models found related to rc airplane skis.thingiverse
RC airplane skis, 18cm by 6cm. The "light" version is 1.5 mm thick and 30grams (printed in PLA at 100% infill) and quite flexible, it is suitable for a lighter plane. The heavy duty version is 4mm thick and 71g (printed in PLA at 100% infill), very...
cults3d
Skis for rc aircraft. I have included two sizes. The smaller size is good for small planes like Flite Test mighty minis. The larger size should be good for larger Flite Test planes but you can scale them to any size you need. ...You will need to mirror...
thingiverse
The landing gear on the sport cub is ok for the skis on snow, but it has a tendency to dip the nose on take off. Speed is your friend and always keep plane into the wind. I used rubber bands to keep ski tips up. You can attach the rubber bands...
cults3d
Created to fit around a wheel, slots added for velcro. ...SLDPRT file provided for adjustments to fit your airplane.
pinshape
It should fit most electric RC airplanes with tricycle or tail dragger front wheels in the same 1/8 in. wire wheel struts. The file with skig is for the front steering wheel. After printing you will need to heat up the front part (first 1 in.) of...
thingiverse
It should fit most electric RC airplanes with tricycle or tail dragger front wheels in the same 1/8 in. wire wheel struts. The file with skig is for the front steering wheel. After printing you will need to heat up the front part (first 1 in.) of...
thingiverse
I Made a ski for a couple of my rc planes. The many holes in the mounting plat is for adjustment. The holes are 4 and 5mm. I will be changing this as I print them and test them. To print I scaled mine down by 0.9 My planes can't take off with...
cults3d
... flight was sent up a bit. The size of the ski 160x50x2 mm weigth ~20g , perfect for an airplane weighing 500 g. With such skis, the airplane will be able to take off and land on the snow. ... Forum(RU): http://rchandmade.ru/viewtopic.php?f=94&t=374
thingiverse
... was sent up a bit. The size of the ski 160x50x2 mm weigth ~20g , perfect for an airplane weighing 500 g. With such skis, the airplane will be able to take off and land on the snow. ... Forum(RU): http://rchandmade.ru/viewtopic.php?f=94&t=374
thingiverse
Tail ski for Sebart Sukhoi 29S 140E (or any plane up to 6kg) Tail ski for pattern F3A plane (up to 2 meters wingspan) For main skiing I recommend use this DuBro skies http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXWH30&P=7 If somebody wants I can...
thingiverse
Skis made for a Turbo Timber / Timber. ...Sand/Paint to give a smooth bottom surface to reduce friction on the snow. Use a rubber band on each ski to keep the tips up when off the snow.
thingiverse
These skis are designed to fit a Tamiya Madbull or other RC car with similar steering arms (5mm dia. x 20mm long). Also uploaded STLs for mk2 skis with a more angled pattern to bite when turning. ... ...
thingiverse
When you start pimping you RC aircraft with bigger engines and bigger propellers, you risk destroying everything in a hard landing. These skis goes onto the wing tips and protects the propellers against groundstrikes. On a Multiplex Twinstar II...
thingiverse
This is a custom designed ski set for a 1/10 scale RC truck. The design is a little different than the off the shelf versions as this replaces the steering hub instead of bolting onto the axle. This reduces the risk of the ski rolling over and takes...
thingiverse
I designed this set of skis for my traxxas rustler to traverse the snow more efficiently. On the back wheels I have a pair of sand/snow paddle tires to get more traction. ...Also be where that not all rc cars are water/snow proof.
thingiverse
Snow Skis for an RC Plane. These are about 7.5 inches long as printed. The scad file is poorly commented and I am a hack coder so if folks show interest I will comment it further. There is a scale function at end of code allowing you customize in...
thingiverse
These are skis which can be printed and used with any RC aircraft for takeoffs and landings on snow. I use them on my Horizon Twin Otter and they're great fun. They are 7.5 inches in length and 1.5 inches wide. They are designed for 3mm wire gear...
thingiverse
Made some skis to my Thunder tiger cessna 177 to be able to fly on snow/ice during winter.
thingiverse
210 mm and 175 mm log skis. The axle holes are for 3mm-1/8" wire butmay need drilling to fit. After printing sand and fill the curved underside with thick CA and then glue the keels. ...Use a spring, rubber band or rubber bumper to hold it level in...
thingiverse
They are designed to be held on with rubber bands over the wheels and "sprung" with either a cut rubber band or elastic thread for the front and back to keep the skis at the correct attitude. Be sure to take them off when you're done flying so the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=273099 Instructions Using the following options: border_depth = 1 borderdistance = 5 borderradius = 8 letter_depth = 1 letter_size = 7 holediameter = 3 name4 = RC AIRPLANES name3 = ALL THESE...
grabcad
THIS IS A DESIGN OF A AIRPLANE TRAINER WOODEN FERRY, STILL NOT READY. ...PLEASE LEAVE YOUR COMMENTS.
thingiverse
Made some snow skis for the arrows rc bigfoot. I usually don't make a tail ski anymore since it just drags in the snow like the wheel does. Just print 2 of these skis, they are the same for left and right. After you print them, you will make the...