redcat rc 3d models

Crafted specifically for the RedCat Racing short course original tire, they address the issue of non-standard 1/10 scale size and subpar quality of the original rims. An additional rim features a robust 12mm / 6mm hex design with reinforced spokes...

FPV camera and holder for Redcat Gen7 RC to replace light bar. ... Just for fun!

The Redcat Racing differential I utilized to construct my personal RC is surprisingly compact compared to my expectations upon purchase. A more advantageous model could have been acquired prior to this experience. Nonetheless, I hope others find this...

... faces but only one set of barrels to use them in. ...Redcat has no plans to make barrels available so I made these totally unofficial barrels for all the RCers who want to use them on other cars. ...Take it, mod it, do what you like , all yours kids.

I was determined to find a solution for mounting lights on my RC truck, so I created a custom mount that slides effortlessly over the front bumper. ...To illuminate the night, I opted for vibrant RGB LED strips that are an impressive 10mm in width,...

I installed this same bar on my Redcat Racing Volcano EPX, and although it's slightly oversized, it gives the car a minimal amount of toe in compared to the original bar. ...I utilized ABS plastic so that it would have more flexibility because I had...

Innovative Solutions Take Center Stage for On-Road Vehicles as Manufacturers Boost Infill Levels to 1000 Percent, Revolutionizing the Industry with Unprecedented Efficiency and Performance.

It is intended for a Redcat Racing Volcano EPX but should work well with almost any 1/10 scale rc vehicle. I used a clip mount from https://www.thingiverse.com/thing:539135 to secure it in place. Update: The design has been revised to fit the truck...

It is for a Redcat Racing Volcano EPX but would probably work on almost any 1/10 scale rc vehicle https://www.amazon.com/Redcat-Racing-Electric-Volcano-Included/dp/B00HVBVNVG/ref=sr_1_3?ie=UTF8&qid=1514388781&sr=8-3&keywords=volcano+epx I used the...

I whipped up a custom paddle tire for my Redcat Volcano EPX Pro - printed in TPU, it fits snugly onto any 2.8 style rim with standard glue-on beads. ...Enjoy!

Modele Europe Maverick Blackout MT

This a 1/10 scale RC hitch mounted dirt bike carrier for New Ray 1/10 scale dirt bikes The New Ray bikes have a little connector on the bottom for their stand that will connect to my carrier so no need to strap it down.

These are mounting trays for the ESS-One and ESS-Dual RC sound simulators designed specifically for a clean install on the Redcat Gen 8 Scout II, making it easy to remove the unit. <b>Shock Brace Mount Instructions:</b> These mounts attach over the...

... assembled wheel. sized slightly larger than the dimensions of a stock redcat gen 8 international scout II. may need to resize for different sized wheels depending on how you want it to look. ...will upload a blank version as well as other I've made

It should fit most 1/10 scale RC cars, as the front width measures 65mm and the rear is 62mm. This setup should accommodate most action cameras. https://www.youtube.com/watch?v=SvoHglxpeDY YouTube Channel:...

Custom grille for the Redcat Kaiju RC Body. ...Holes for 5mm lights.

Custom grille for the Redcat Kaiju RC Body. ...Holes for 5mm lights.

A simple floor pan for the back of a Redcat Gen8 rc truck. I just wanted something to block light from shining through the truck to make it look more solid and scale appropriate. It is sized to have the rear bumper moved forward a couple of holes to...

Body Post (Part # 86786) for a Redcat Monsoon RC Truggy. No holes, you'll have to drill those yourself, too hard for FFF printing. Not recommended for resin printers due to the brittleness of the resin. Print 100% infill using CF-Nylon or other...

Body Post (Part # 86786) for a Redcat Monsoon RC Truggy. No holes, you'll have to drill those yourself, too hard for FFF printing. Not recommended for resin printers due to the brittleness of the resin. Print 100% infill using CF-Nylon or other tuff...

Human: 55 Tooth Spur Gear Replacement for Redcat Racing RC Vehicles. Compatible with Blackout SC, Blackout SC Pro, Blackout xbe, Blackout xbe Pro, Blackout XTE, Blackout XTE Pro Models. ... I needed a quick fix and this spur gear is designed to serve...

# Redcat Shock Mount OpenSCAD Design file(s) for 3D-printed replacement shock mount for Redcat RC car Big Bore Shock. Replacement part: Shock/Spring mounting cup, which is a single plastic piece of the Redcat Racing "Big Bore Shock" item ([PN:...

Redcat Gen8 Spur Gear Spare Part File SpurGear_Module08_32DP_45T.stl This is the gear spare part for Redcat Gen8 RC car, Module 0.8, 32DP, 45Teeth, which works with the Redcat Pinion Gear 17T (Part No. 11177). You can also order a plastic one from...

Feline Fury Logo

Center mounted servo bracket for Redcat Gen8 Scout: a DIY solution born out of thriftiness. I opted to fabricate my own rather than splurge on an aluminum one. The design includes two variations - standard bumper height and raised bumper height - so...

This is a replacement piece for the link end connectors for the Redcat Gen8. ...Or any RC that uses 5mm ball ends and 3mm screws.

Towering body kits available for a variety of high-performance RC models, including the Exceed DriftStar, equivalent to the HSP Flying Fish and RedCat Lightning.

My son was constantly stripping out the nut that the wheel glides onto on his Redcat Volcano RC truck, so we chose to create a replacement. This nut fits perfectly and functions well, taking only a few minutes to print and costing mere pennies to...

RedCat Racing 16mm ShockCup

Redcat Gen7 Rear Bumper Fits: Redcat Gen7 Sport/Pro Hardwere needed for the installation: Type Size Length Qty Socket Bolt M6 25[mm] 2 Socket Bolt M3 16[mm] 4 Nyloc Nut M3 4 Optional Add ons: Winch (Aliexpress-INJORA) LED lights (Aliexpress--AXSPEED...