runcam swift 2 fpv 3d models

(Personally, I'm not convinced of the benefits of squash-ball feet, as they seem to increase ringing artefacts on printouts.) By the way, the standard CR-10 filament holder can be installed on the top of the printer, with no modifications to the...

The upper side of the mausoleum structure is covered with a flat roof made of lead. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: Doesn't Matter Supports: NoResolution: 0.1~0.2 Infill: %10~%15 Filament: NA PLA NA Notes: There...

When you're ready for the final feet, you can print all three at once, in correct-side-up orientation, without supports.  I printed these solid using max perimeters.      2:  Seat PostPrint this part upside down (wrong-side-up), and you should have...

If they're too tight the clear out the spacer hole with a drill or sand the pins a bit. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Doesn't Matter Resolution: .2 Infill: 20% Filament: Amz PLA Blue Notes: After...

Lesson Plan and Activity Day 1-2: Get kids excited by watching this video https://youtu.be/LZFF8EuaGjM and using Google Earth, start zoomed completely in on your city. Then begin to zoom out to your state, country, and finally, the world, discussing...

Print Settings Printer Brand: RepRap Printer: RepRap Kossel Rafts: No Supports: No Resolution: 0.2 Infill: 25-30% Notes: Select infill to taste based on the strength needed. I found that 30% was more than sufficient to handle the requirements for the...

I Used the following Electronic and off the shelf pieces for this project: Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500https://www.adafruit.com/product/3061 - uses external Antenna Also available with a built in antenna -...

Dafür brauchen wir 2 Datein: Tool zum Upload: https://github.com/marcelstoer/nodemcu-pyflasher/releases Programm: https://github.com/Aircoookie/WLED/releases (WLED_X.XX.X-xx_ESP8266.bin) Der ESP(blaue Platine) muss per USB an den PC angeschlossen...

The print came out nicely and after carefully removing support for a couple minutes, I used it with my cell phone flashlight and found that it works acceptably but a Maglite 2 AAA LED flashlight with the top off (candle mode) is an amazing light...

 I printed with three walls and 15% infill gyroid at a .2 mm layer height for all of them.  I used an interface layer with PolySupport to make the edge even cleaner.PLA is what I tested with and works fine (the colors in the example are Printed Solid...

The switch should snap in place. 2) Push in the flashlight glass on the lightsaber cap until it's locked in place. 3) Insert the reflector, which will also help hold the glass in place. (The red color of the blade may become pinkish because of the...

EXTRUDER CALIBRATION The 2 extruders should be calibrated Just fine but you can tweak this settings by sending g-codes to the printer. Get your old E-Steps with M503. Look for the line starting with M92, the value after the E are your current...

Reduce the charger current to 100-200mA , remove the 1.2k SMD resistor and solder 5.1-10k between pin 2 and GND on the board. Glue the charger board in place. Connect the 14500 AA Li-Ion battery, solder the HV cables (add extra shrink tube isolation...

2. Upside-down to raise your prescription lenses up to help when shooting billiards (pool). 3. Upside-down for watching anything at a distance and also allowing the wearer the opportunity to look below their glasses to view a mobile device or read a...

Day and night version There are 2 blend files included, a Eevee and Cycles version. The Cycles version can also be used for night renders. Animated All doors are animated by keyframes. These keyframes can be moved to suit your animation or static...

Beard prop by Quinventor https://www.thingiverse.com/thing:2856668 body from Shaggy https://www.thingiverse.com/thing:3391379 tuft of hair from Tani v0.3m WIP by fASE-2 https://www.thingiverse.com/thing:3404875 main hair from Ben Franklin...

... side opposite the spray holes</p> <p>The lower threaded portion and the spray nozzles should be printed at 0.15mm layer height for quality. Between 9.95mm and 105mm can be set to 0.30mm layer height for reduced print time 2 perimeters and 15% Infill

A pdf booklet contains the list of challenges for both the basic and expanded set, as well as some additional background material on six-piece burrs.The Starter Burr Set is fully compatible with the much larger Extensible Burr Set, so you can expand...

You may use whatever color scheme you wish; for the print shown in the photos, I used five different colors, with pieces-2 and pieces-3 in the same color.This puzzle uses "snap joints" so that it can be printed without supports. After you print it,...

Mine is inspired by a number of different dry box builds and parts, including:Sterilite 20qt Filament Dry Box by StvPtrsn on ThingiverseAngled Dry Box Feeder with Source by Bolukan on ThingiverseFor this build you will need the following parts:17x...

...Note that this is my first experience with HTML, JavaScript, and JSON programming, so please be gentle in the comments. Finally, the case was designed using Autodesk Fusion 360, sliced using Cura 2.7.0, and printed in PLA on an Ultimaker 3 Extended.

2/24/21 Uploaded correct version of the DW660 Lower Mount. This accessory is an add-on to V1 Engineering's MPCNC Primo version CNC machine and provides a mount and dust collection attachment for the DeWalt 660 Router. See...

Young -- 20,878 polygons -- 2.15m tall. Smaller plant some halfway through its maturing cycle. Immature -- 554 polygons -- 66.17cm tall. A small plant that hasn't reached its mature aspect. Sapling -- 101 polygons -- 18.27cm tall. A very small and...

I printed this in 0.2 layer height, with 3 walls and 35% infill, with supports everywhere (again note the warning on the parts listed above). To assemble, this will require: 4x M2.5x20mm screws 4x M2.5 nuts 4x M3x12mm screws (or longer depending...

No, I wont make you a 20 Degree mount, use tinkercad...this covers the battery area and has extra protection over the USB port so you can run no battery and use a BEC * needs supports (lots of waste here) * 3 walls * 16% infill (i use gyroid) *...

Hat &amp; Headers are CA glued in place, then hatch waterproofed w/ candle wax &amp; heat.Extended Latch: Overture Space Gray PETG at 0.2 layer, no supportBoat Stand: Prusament Ultramarine Blue @0.3mm, no supportNote: Any gcode files with “TL” in...

I'm sure there is a similar feature for other slicers, something about -0.1 (negative number) should fix. I cannot add anymore to those numbers since the parts are already too loose on my printer and this supposed to be a precise tool. *Updated...

... make my own thats modeled after them an add to this thing so all the files i used will be accessible to anyone who wants to try them. 1: https://www.thingiverse.com/thing:5504523 hanger 2: https://www.thingiverse.com/thing:3337735 puck for stand

You need only 1 so choose wisely :DBranch parts: you have 4 versions to choose: 2 or 3 branches, each printable with or without support. I used &nbsp;branches with support. For the standard tree you will need this part 21 times. For a different hight...

When curing I have found it best to turn the trains and carriages on their side to expose the base for a 2-minute cure, then stand up and run a 6-minute cure. PAINTING, SEALING and STORING I base coat the minis with an acrylic white (I use a...