sapphire plus firmware 3d models

(print it upside down with supports for the 4 screws holes) *For old version read below* My design of a simple adapter to use Sherpa Mini Extruder by Annex Engineering on original gantry for Sapphire Pro or Plus. You need to use two button head...

... tape to the bed brackets underneath Z endstops. You will need 2 of these, 1 for each side. Print Settings Printer: Sapphire Plus Rafts: No Supports: Yes Resolution: 0.24 Infill: 25% Filament: ideagen3D PETG Orange Category: 3D Printer Accessories

Mount para Sapphire Pro/Pluspara V6. ...Adapatação do mount para Sapphire https://www.thingiverse.com/thing:4337458 de r31l4nd, incluindo o suporte para Autolev, sensor de ABL. ... Ainda em desenvolvimento.

Mount for the Biqu H2 extruder on the Sapphire Plus (SP5), probably also would work on SP3.-Mounts on two points, to keep nozzle very firmly in place. One mount goes between the hotend fan and heat sink, the other around the extruder and integrates a...

Remixed from [R31L4ND's E3D V6 Hotend Mount](https://www.thingiverse.com/thing:4337458) for the Sapphire Plus to better support the Mosquito/Spider & clone hotends. The collar and BLTouch mount have not been changed - feel free to re-use...

This is a case that I designed to use Klipperscreen with the Waveshare 5 inch DSI display (800x480) in the Sapphire Plus (SP-5) or Pro (SP-3).In addition to KlipperScreen, it can also be used with Octoprint with Octoscreen.It can be installed by...

My mods for Sapphire Plus printer. This will allow you to mount the BMG extruder on top of the hotend. The mount will shorten your ptfe tube to 95mm. I also made a short tube to stiffen the ptfe tube since it was moving a bit. I also suggest to...

Includes frame to attach the gauge to Sapphire Pro and Plus, as well as Creality the printers with a single cooling fan. Level one corner using the paper method, zero the probe then move the print head to the other 3 corners and adjust until the...

This is a case that I designed to use Klipperscreen with the Waveshare 4 inch HDMI display (800x480) in the Sapphire Plus (SP-5) or Pro (SP-3).In addition to KlipperScreen, it can also be used with Octoprint with Octoscreen.It can be installed by...

This is a case that I designed to use Klipperscreen with the Waveshare 5 inch DSI display (800x480) in the Sapphire Plus (SP-5) or Pro (SP-3).In addition to KlipperScreen, it can also be used with Octoprint with Octoscreen.It can be installed by...

Includes frame to attach the gauge to Sapphire Pro and Plus, as well as Creality the printers with a single cooling fan. Attribution should go to dalul96 for this thing: https://www.thingiverse.com/thing:3041642 as I copied the way the corners...

This added file combines the Marlin Firmware for the Anycubic Kossel Plus with modifications from the FLSUN kossel firmware. The Anycubic company has not updated the editable firmware, making it necessary to level the printer correctly. The most...

This is 32-bit firmware for a Creality Ender 5 Plus with a V4.2.7 Creality mainboard installed and is based on Marlin 2.1.2.1. Features included: Compiled for the 32 bit Creality V4.2.7 main boards. X & Y home positions are stock. BLTouch...

https://s.click.aliexpress.com/e/_AXS9vp** After looking at all the options for a hotend mount here on Thingiverse and Facebook i decided to design my own mainly for the Sapphire Plus but it should work for the newer Pro models aswell. I did not...

This added file is a blend of the Marlin Firmware for the Anycubic Kossel Plus, and incorporated changes from the firmware of FLSUN kossel. Anycubic has not updated the editable firmware, requiring levelling of the printer to be done correctly. The...

For finish, this is the same firmware I've in my Kossel linear plus, no changes, it works very well and i've tested all functions a lot of times, all works good, no problems. Just don't forget to initialize eeprom after flash or send M502 command...

hi!I've build one because, it's impossible to find one who works correctly.The firmware is in french, V2 probe and for A4988 or TMC2208 steppers drivers.Just invert the steppers rotation for A4988 drivers.the z probe offset is easier to adjust, just...

Optionally, add a small push-button switch (pictured,) and install this remixed firmware to provide on/off and reversing functionality: Click once = On Double click = Reverse Direction Long press = Off Important! You'll need to include the...

... same firmware would not update," please continue to steps 5-7） 5. Print the "UI_4_3-单头快速.bin" file 6. Print the "wifiUpdate_full_V10.0.12.bin" file 7. Print the " PLUS X-MAX参数.gcode" file After you print all the 4 files, the updating will be done.

The configuration files work on firmware 1.02-2.01 I'm using TMC 2209 on Z and E1 Optical Endstop (The 'red' Version): https://aliexpress.com/item/32959048821.html?spm=a2g0s.8937460.0.0.3b8e2e0eEBZfmJ...

... fan part of the mount and lock the 4020 fan in place using 3 m3x16 bolts. 3. Connect the fan to your motherboard and modify your machine's firmware. Enjoy the additional cooling! ...Any additional tips to improve this design are most welcome.

Mise à jour de votre imprimante et de l’écran tactile d’origine en FrançaisEnder-5 Plus : carte mère d’origine ou silencieuse V2.2.1Ender-6 : Avec ou Sans BLTouchCR10MAX : carte mère d’origine   Le tutoriel fonctionne avec les cartes mères...

2018/3/2 - changed 'DEFAULT_RETRACT_ACCELERATION' of TMC2100 to '200' - redesigned the delta calibration circle 2018/2/28 - changed the z-offset of piezo sensor to '-0.07' 2018/2/26 - added firmware for Anycubic Kossel Plus 2018/2/24 - changed the...

You will need the following screws:2 M4x12 screws with 2 assorted nuts,2 washers and 1 M4x8 screw for the main mount (rear side).2 M3x12 screws with assorted nuts and washers for the main mount (front side).2 M3x12 screws with washers for the main...

These are my custom config files for the Ender 5 Plus with Marlin 2.0 Firmware on a SKR 1.3 motherboard (I have a 1.4 Turbo installed, but I haven't had time to update it yet). They are very specific to my machine, but I thought others might find...

I'm creating a new work of art, inspired by a concept that Ross Tran brought to life on DeviantArt with his piece "Sapphire" - https://www.deviantart.com/rossdraws/art/Sapphire-698976408. This hand-painted study is all about capturing the emotions...

This is my Version of Marlin 2.0.7 for the Sunlu S8 Plus with Bigtreetech SKR 1.4 Turbo Mainboard, TMC2208 Standalone Stepper Drivers (1 Driver for both Z-Stepper), TFT35V3 and Automatic Bed Leveling (BL Touch). ... This is not the final Version, but...

comment with // for normal size #define ANYCUBIC_KOSSEL_PLUS // Anycubic Probe version 1 or 2 see README.md; 0 for no probe // Typically the probes for the Anycubic Delta Kossel printers come in two different versions. // * Version 1: Z Probe Offset...

##These files are configured for the Anycubic Kossel Delta Plus.## #See 8/4 Edit # The Configuration.h file sets the Z_Probe_Offset to -15.70, however this setting may not be suitable for your printer. Key elements of this configuration include: ...

X-axis, attention - on the right there is a protrusion similar to the left one (in my delivery it was just like that)