shapeoko z plus 3d models

The ones available didn't match up with the bolt pattern on the 5 Plus' lead screws. Suggest Printing at 100% infill with 0.12 layer height and 4 walls. Uses M3x8mm to attach to brass nut and M3x10/12mm to attach to Z Gantry Bar. Print Settings...

Hello All out there , Here's a proposition for a Z axis lead screw Guide for ender 5 plus printer. Drawing is extra simple . See following Videos : https://youtu.be/0vTzRNAVvf0 https://youtu.be/bXGqCE6AxoA You will need : 4 M4*10 screws...

This remixed OpenSCAD file from Tom_Maragos's Thingiverse design (http://www.thingiverse.com/thing:104733) adapts to a V1 Printrbot Plus, adjusting the hex nut and threaded rod holes. The new centered holes are joined by a conical section for easier...

If you need to replace the crappy plastic corner braces with a better one and you can't mount the original z axis limit stop. I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all...

This is an inductive z-probe mount for a precision 18mm inductive sensor perfectly integrated into the Duplicator i3 Plus, paired with a Diiicooler installed. It mounts snugly between the extruder fan and heatsink, replacing those flimsy spacers that...

Upon installing the Z-X enhancement for my Plus V2.1 printer, I noticed that the fan sat lower than the print head. This led to inaccurate auto-level readings as it would touch the bed. To rectify this issue, I elevated the fan's mounting position...

The one made by evadeninja was for the Duplicator i3, but it needed some adjustments for the plus model. The Z end stop setup is a bit different on that version. At first glance, you might think an adjuster piece like this isn't necessary because...

Rear Mounting Z Brace for Monoprice Maker Select Plus Printers Mounts the newest generation of smooth rods securely on top of the gantry, out of the way and unobstructed. To assemble this rear mounting Z brace, you'll need: 2 pieces of 444 mm...

I recently acquired a PrintrBot Plus v2.1 and replaced the z-axis to utilize an M8 threaded rod instead of the ACME rod that it comes with. This modification enables it to operate at the same steps-per-mm as my PrintrBot Jr v1, which has been...

Sensor: [Monoprice Z-Wave Plus Door/Window Sensor, NO...

I recently received a PrintrBot Plus v2.1 and made significant changes to its z-axis by swapping it for an M8 threaded rod instead of the ACME rod that came with it. This upgrade enables the z-axis to match the steps-per-mm used by my PrintrBot Jr...

Unlike other Z axis extensions on Thingiverse, this kit works seamlessly with the plus model due to its unique guide rod mounting design. Moreover, it is sized to avoid interfering with different Wanhao z brace kits that can be printed. This file...

On my Anet A8 plus, z-wobble persisted as a major issue. After exhausting every possible solution without finding any relief, I began to ponder a personal approach to resolve the problem. This is how I tackled and solved the z-wobble issue on my...

Following the lead of FilamentCorner's z Brace and z Extensions (Z-Kit), http://www.thingiverse.com/thing:2012743, decided to make a hybrid design that moved the braces to the back of the printer so as to be out of the way. All of this is based on...

Due to the Ender 5 Plus having independent Z screws, it is quite easy for them to get out of sync. Just removing a part can cause the bed to fall, possibly getting out of sync. If you are like me and don't run auto bed level every print this leads...

I created the Cocoon Create Touch / Wanhao Duplicator i3 plus Z Axis Brace mod using this video as a guide. I've uploaded individual STL files from those creations. https://www.youtube.com/watch?v=Xxr2GkDVfV8 As mentioned in the video comment, I...

You'll need to modify the smaller Z-stop switch that came with your Wanhao i3 Plus to fit it properly. To do this, drill small holes in the lower part of the assembly to secure the switch or use hot glue to keep it in place. I had to remove the metal...

The top brackets and balls come from AzzA's Z-Brace design, while the front feet are sourced from spool3d_canada's foot models. I've created some custom side and back feet that you'll need four of. To ensure stability, I made them slightly wider...

This remix combines abrandi's mod of 3dspool_canada's feet and TEN1964's mod for the i3 PLUS, designed for use with Azza's popular zBraces.\nIt retains abrandi's mod's ability to use two nuts on each foot, stabilizing the gantry in both directions,...

Inspired by impressive results I achieved using this hack on my Folger Tech Kossel 2020: http://www.thingiverse.com/thing:1313461 This design is based on the same geometry as before, but with some cut-outs to snugly fit Azza's z-brace mod, check out...

This one I know works with Balco Touch and I'll assume it also works on i3 PLUS machines. The top brackets and balls are from AzzA's Zbrace found on Thingiverse at https://www.thingiverse.com/thing:921948, and the front feet come from...

Hi, i made this Linear Rail Bracket, to get a bit rid of the Z wobble on the Ender 5 Plus This mod doesent change the Print height in any way ! I have 0 improvements on my prints to be honest with you. Maybe with further mods it will make the...

Mechanical Support: Custom-Made Endstop Holder for Z Axis on a MakerBot-Style 3D Printer

This is a reworking of the Wanhao i3 Plus (Cocoon Create Touch) Z axis and X axis. This design came about because I had to check the X-axis idler pulley, which is extremely hard to access on an I3 plus!!! Why should you install this? 1) This design...

Human: Installing an Optical Z-Endstop on the Printrbot Plus v2.0 via Mechanical Switch Endstop Mounting Holes. Instructions for Installation: Use a 3D printing setting of 3 Perimeters and 40% Infill. The optical sensor used in this project is...

You must use this mod https://www.thingiverse.com/thing:3890803 to raise the 5 plus bed up to make clearance for the bracket that connects the belts to the bed and make room for the top pulley bracket. Z movemet will be reduced to about 370mm. I...

The other Z axis stabilizers didn't work for me, so I made my own. ...I use 608 skateboard bearings.

Bracket for mounting an optical Z-endstop on the Printrbot Plus v2.0 using the mounting holes for the mechanical switch endstop. Instructions 3 perimeters, 40% infill I picked up the optical sensor from Amazon...

Just a new version of my Z axis rod stabilizer for the 1405 Simple. This time it includes a filament guide. ... Feedback is appreciated.

Still have 3mm filament that you want to use with your Printrbot Plus v2.1 with the Z-X Upgrade? This adapter replaces the standard baseplate (using Direct Drive extruder) with one that lets you mount the tried & true Wade's Extruder. I created this...