skylight 3d models

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

In my models are embossed labels A, B and C for easier assembly. Length A is 350 mm and you will need 30 piecesLength B is 398 mm and you will need 44 pieces (45 if you want full dome without entrance)Length C is 500 mm and you will need 10...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

The water pipe has an improved shape that looks way better after being printed than the last model. Inner pot V2: made the border higher so there is more colour. SCROLL DOWN FOR DETAILED INSTRUCTIONS WITH PICTURES ! When using this flowerpot it's...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

For other projects and creations, please visit my Instagram page (https://www.instagram.com/roger.egli/) or check out my YouTube playlists for model/machining hobbies (https://www.youtube.com/user/MrZhefish/playlists). Hope you find this mod...

Don't use it for rendering or model generation. (see Reducer picture)</p> <p>PRINTING NOTE</p> <p>Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside.</p> <p>These are for sink and...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

&nbsp; Quite a racket.What you'll need:&nbsp;1 - each of all the model parts listed, except2 - each of the Cylinder part1 - &nbsp;¼-20 x 2.5" hex bolt (or 6mm x 65mm metric hex bolt)1 - ¼-20 hex nut (or 6mm hex nut)6 - medium sized nylon...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

Licensed models were manufactured in Germany, Sweden and Russia First Fighter The Type L is famous for being used by Roland Garros to shoot down three German aircraft in April of 1915. This was a special single-seat arrangement made for the tennis...

Bbut if you have a problem with the fit please provide some feedback, and if possible the flat to flat measurement of the 5/16-18 nuts you are using with this model. Note that if you find that both the nuts and the bearings don't fit, you should...

&nbsp;After getting the other nosecone to work I found out that the original Sprint used a BNC-50X and I had modeled off the BNC-50Y. &nbsp;So for ‘authenticity sake’ I've added a BNC-50X version of both the stock and Astrocam nosecones.</p><figure...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

Perfect for storing jewelry, electronic parts, cables, Lego models, tools, and other small items, the Pyramid Stacker offers a practical solution for keeping your belongings organized and within reach. By stacking the layers, you can store smaller...

This model drops excess wind The concept is to use it quietly This mod may be a bit more difficult 5015-24v fan 5015-12v or 24v fan * Please note that the polarity of the fan electrodes may be reversed. DC-DC adjustable step-down power supply I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Print Settings: - Printer Brand: MakerBot - Printer Model: MakerBot Replicator 2X - Rafts: No - Supports: Yes Important Print Note: The key thing to keep in mind when printing these wheels is to use support material, especially for filling in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

The printed parts needed are here:https://www.printables.com/model/134871-qidi-x-max-improved-x-gantry-with-tensionershttps://www.printables.com/model/91206-adjustable-belt-tensionThe CF Rod Plug listed belowNote: It is highly recommended that you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

If you have a V3 or want to upgrade your V2 to a V3, go to the V3 mod.&nbsp;Minimalist parts required to convert the LumenPnP from v-slot rollers to linear rails. This preserves the overall dimensions and travel of the machine, as well as maintaining...