smallest 3d printed object

It is highly recommended to print this box in PETG due to PLA's tendency to deform over time under compression, compromising the box's structural integrity. To further enhance stability, consider supporting it from below with rubber feet, ensuring a...

All parts were printed with a 0.2mm Layer height. 3 perimeters, and 20% infill. I used PETG, however other materials would also work. A hardware list is provided. You may also need some basic tools, knifes, small drill bits, etc. Most parts...

(ALL OF THE ABOVE ICONS ARE ALSO SOLD SEPARATELY ON MY PROFILE.) (MIRROR THE ICONS FOR USE ON THE RIGHT SHOULDER PLATE SO THE ICON IS FACING FORWARDS AS INTENDED, THIS CAN BE DONE EASILY IN ALL SLICERS) These models are designed to be fitted atop...

Please be so kind as to leave a tip if you decide to print and install this and share your results. Advantages of this design: - Universal - Suitable for hotend and under bed installation - No loss of build volume in any direction - Easy...

This version still prints without supports if you turn it upside down in the slicer. ---------------------------------------- I have an Orphan Espresso 58mm dosing funnel already, but I wanted to create one that sits on top of the basket instead of...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable retainer...

I printed all the parts with PETG, 5 perimeters, 40% Infill. The EndPin for the optical endstop must be black (or painted with a marker). They will require support in places where there are nuts or countersunked holes. I have included a small test...

Fit Ears - Pink, Helmet part 1 - White and Helmet part  - White into Helmet - Red as seen in the picture below. NOTES:The Mag Chest and/or the Mag Waist will only be able to be printed at 100% due to it using 3mm x 1mm magnets. ...Any size other than...

Since publishing the Filament Server System in 2013, I've sought a more efficient system requiring less printing, fewer loose parts, easier assembly, and simpler spool changeovers. When creating the pipe-based, wall-mounted Spool Storage Rack last...

Through his friend James Ballantyne's printing press in Kelso, Scott published his early works, including "Glenfinlas" and "The Eve of St. John." His poetry brought him to public attention, and in 1805, The Lay of the Last Minstrel captured the...

 The cutter tool is flush with the MK3S(+) printer.If used without mount, has some small areas for magnets inside the compartment so that you could attach to anything else (like a refrigerator magnet)Exterior of mount has openings on each side...

- https://amzn.to/3bAgYBv Uses M3x3mm knurled brass heat-set inserts found here - https://amzn.to/2LQwDld Uses 1 M3x6mm screw found in this kit - https://amzn.to/39q2otO *Note: This post contains Amazon Affiliate links that support The...

Print both plastic parts and insert 10 heat set inserts into Toolhead body 2. Mount endstop switch into position with 1xM3x8 screw and immediatelly attach its cable. Later will not be possible to plug cable into endstop. Other end of cable should go...

If you want to support my work, you can contribute with me by donating to this PayPal account. Print SettingsRafts:NoSupports:YesResolution:0.3Notes:If you set the wall width to one filament line (0.4~0.6mm) and the infill overlap to higher...

Can be printed with a moving head. Arkham Horror investigator - the professor by Craigen https://www.thingiverse.com/thing:4649571 Longboi Trophy by HiyuMarten https://www.thingiverse.com/thing:4706958 Stoat by Davision3d ...

Bollards (cross)- print several pieces and glue in vicinity of chocks. Ballast tanks can be filled through ballast vent pipes and emptied by syringe with flexible pipe connected to sounding pipes. Pay attention during ballast operations- excessive...

... let me know in the comments! Printer: Flux Delta Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 80% Post-Printing I designed this using OpenSCAD, and it was a total pain! ...I'm going to have to learn SketchUp or something one of these days....

The "Upper parts" contains: -Mosquito/Dirt Blocker (updated to be perforated) -funnel -Pipe attachment (needs to be epoxied/glued into bottom of funnel) -Feet should be printed as needed. need minimum of 4 feet to support weight. The "Funnel" STL...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

To print a complete set of parts for the offset enclosure (To clarify, this is the area from the IKEA Lack table top the printer sits upon- to the top of the enclosure formed by a 2nd Lack table top), you will need one of each component excluding...

I suggest printing the top pieces in something more heat resistant than just PLA, preferably carbon fiber nylon or polycarbonate. ASA should work pretty well too. For the bottom pieces, I used PETG as it allowed for the cards to slide in and out...

For this, you will need a few parts: EzStruder direct drive or bowden doesn't matter Low profile motor support printed part (see my thingiverse thing) 30x30mm Fan shroud v3 (or other thingiverse thing version) 3 fans of 30x30mm (or different size,...

Threads for fastening the spindle nut with 4 M3x15mm cylinder head screws are also printed. 2020/03/09: Version 1.0.4a: Version without a cam for triggering optional limit switches. 2020/03/10: Smaller dimensional changes: Distance between spindle...

To print: Ender 5 Normal: ---------------------- Ender 5 and 5 Plus RAILMOD - Tensioner Side v2.0.stl Ender 5 and 5 Plus RAILMOD - Motor Side v2.0.stl Ender 5 RAISED RAILMOD - Bearing Bracket v2.0.stl Ender 5 RAISED RAILMOD - Carriage v2.0.stl Ender...

Secure LED-module in place with a drop of superglue or a tape. OpenSCAD file attached for easy modification. Enjoy! Strandtest original: https://github.com/adafruit/Adafruit_NeoPixel/blob/master/examples/strandtest/strandtest.ino LED module used:...

When printing the lower air duct, I did not use support inside of the duct itself; instead, I used some outside. Internal walls are designed to eliminate the need for support which would be difficult to remove. The duct on the extruder holder...

Although, I honestly believe if a goofball like me can figure this out, it should be a lot easier for the rest of you. Print instructionsThe only thing that really needs support in this whole thing is the front door. ...I modeled it as if it were...

Hardware required: QTY=1 M3 Thumbnut QTY=2 M3 Nut QTY=1 M3 oversized washer QTY=1 M3x10 button head screw QTY=2 M3x18 flat head screw QTY=1 M3x20 set screw Thin closed adhesive backed foam (Example: Aerotape) Closed cell foam block to set battery...

BEC set to 3.66V RMS --> VCC Hall sensor board pin 24 Jetson (physical pin == number printed on pcb) --> D0 Hall sensor board GND to GND This configuration is listed on Slack from @Doug and @Tawn (https://donkeycar.slack.com). Thanks to them! I use...