solidex tripod quick release 3d models

Customized version of https://www.thingiverse.com/thing:4427827 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4427827

Category: Camera

engate de reposição para short mas que pode ser usado para outros fins também.

A super simple locking helper including a securing screw, While most rings are based on hand force which can still fail from time to time, this one is intended to add a locking screw, nothing is better than a locking screw ! use it at your own...

QR1 Mount Dimensions: 80 x 40 x 43mmQR1 90° Mount Dimensions: 80 x 41 x 43mmQR2 Mount Dimensions: 80 x 47 x 48mmQR2 90° Mount Dimensions: 80 x 44 x 48mmPrinted at 0.20mm layer height with 6 perimeters on my Bambu Lab P1P using PolyTerra Matte...

Good luck! ...Enjoy yourself!

After experimenting with various 3D clip designs, I discovered that they were too constricting. To overcome this issue, I completely reimagined the design from scratch and rigorously tested numerous printed prototypes until arriving at the final...

Low-poly model ready for VR, AR, games and other real-time apps. Perfectly for FPS. ...Every model has been checked with the appropriate software.

This allows you to take the steering wheel from your Ariel Atom or SPA-compatible wheel and mount it to your wall. The wheel attaches to the mount just like it attaches to the car. Not as secure of a fit, but thats just to make attaching it easier. ... ...

With this clamp it simplifies attaching and detaching a lot quicker. The stainless steel base provides an exceptional strength. Adding a secure plastic bar clip on top helps ensure it stays firmly in place. The key feature though is its cushioning,...

I borrowed the concept from DPC and completely overhauled the latching mechanism. It's now a turn-and-lock system. Additionally, I redesigned the top and bottom to ensure seamless integration with the rubber Apple case. The only component I retained...

This is a remix of https://www.thingiverse.com/thing:636606 and https://www.thingiverse.com/thing:2775204. Thanks to both. I printed this on its end in PLA, so I could minimise the need for supports. ... The supports are also really easy to remove.

Material needed: M5 x 15mm x 2 pieces Rubber Band x 1 piece Demo: https://youtu.be/9kLH9dNlCl0 Rights reserved, do not use for commercial purposes! ...Licensed under the Creative Commons - Attribution - Non-Commercial license.

The fold up steps on our new RV would not allow the door to close with a Camco screen door handle was attached to it, I made these brackets to make the handle easialy removeable. Printed in PETG at 235 C nosel and 80 C bed. ...I found printing on a...

Just added some slots for the screws to hide in.

11/28/22 - I decided no further changes are needed, so it is no longer in WIP status. Edit: 11/21/2022 Added CasterPlate112mm.dxf. The 112mm is the length that I'm using and I think it works well. You can use it in place of the CasterPlate.dxf...

Customized version of https://www.thingiverse.com/thing:4427827 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4427827

To facilitate tightening, I drive a groove into the screws.

This design caters specifically for early Reprappro Mendel builds, which often feature an abundance of redundant 8mm nuts on top bars and an inconveniently placed extruder on the side. By using this model, you can install a bracket to reposition your...

I designed these because I couldn't locate the brass ones, and when I did find them, they were very pricey since they were custom-made. They are meant to replicate these: ...

The drain hose coupling included with our Intex outdoor pool easily detaches when the kids play in the pool whilst draining, thus wearing the threads and making a mess on the deck. This coupling is fed from the inside and sits snug and securely, even...

Customized version of https://www.thingiverse.com/thing:4427827 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4427827

Needed an adaptor for my old G27 steering wheel to mount it on my new direct drive wheelbase. Its designed to be sturdy and ready for a standard 34mm bikesaddle clamp to make it complete. ...

Personalized the grip / mounting plate for my EOS M and added slightly raised brim for aesthetics. The battery door can be openened without removing the plate and I've added a channel to lead the cable for a DC coupler. Kind of a make-shift model...

Customized version of https://www.thingiverse.com/thing:4427827 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4427827

This is an uncomplicated payload rapid deployment system specifically designed for the DJI Mavic Pro. Absolutely no servos or electronic components are needed. ...Additional solitary component files were uploaded on April 19th.

I required a scope mount for my AR-15 Picatinny rail system, therefore I redesigned a setup that incorporates the mount I needed.

I design spare protectors to prevent them from falling off and getting lost, so you can have a convenient backup option available. These protective covers are specifically tailored for the Lidl's Powerfix clamps, however, they may also fit other...

After a lot of use and adjustment of the Fiido D11 saddle post, the plastic part has worn out and I had the problem that I fell through the saddle when I cycled over a bumpy road. The solution is this replacement part in combination with two...

I printed up the original design and found that the bracket wouldn't fit snugly around the rail. I wanted something that would break off if I crashed, which was a concern as a beginner at floating. Initially, I started with Velcro, but added an...