squishy turtle by jake 3d models

Parts you'll need are: - Print out two sets of the STL files for top and bottom - 3 x 8.3mm OD x 300mm long carbon fibre rods - 4 x rail buttons (https://ausrocketry.com.au/hardware/launch-lugs-rail-buttons/rail-buttons-small-1010-pair.html) - 4 x...

This mount is very rigid, there is no droop or wobble induced by having the bulk weight far away from the gantry, it's also as compact as I could get it with the goals I had in mind. The hotend is placed exactly where the original hotend would be, so...

And, as expected, the hinge pins were a bit short, so I made them longer by 30mm to test things out. Update (11-13-2019): Hinges are now the correct length and working fine, but I might try to come up with an even better way to connect the blade to...

I started by putting all the spring plates in the little slots, it's a very loose fit on these but at the time I was waiting on Hong Kong post so I could get measurements. 2. Once the plates are in install the batteries to hold the plates in place ...

In that case, you might wish to speed the print up by downloading the version without the threads in the back. ...<i>I recommend having the threads for confirmation as there are many SAE screw sizes that are close in diameter, and the thread check will...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

This is a massive re-work of the 12" (31cm) long "easy-print/build" Eagle 1 by korb3n and later, alpokemon. The original model had huge issues with the proportions of the center body/pod section, engines and cockpit, when compared with the on-screen...

Traditions set forth by those that came before them is that they could not directly intervene until the slate must be wiped clean again. After numerous millenia,  the Anteokheia will return to bring about the end of an era and civilizations. In...

Yosemite Sam, a cartoon character in the Looney Tunes and Merrie Melodies series of short films produced by Warner Bros. He is commonly depicted as an extremely aggressive, gunslinging outlaw or cowboy with a hair-trigger temper and an intense...

By attaching the smaller cover piece first (which will stay on going forward), it allows me to remove the main cover as needed without unplugging the cable. It also utilizes 2 foam rubber pieces in pockets on either side of cable to hold the cable...

http://www.mcmaster.com/#97725a700/=uytwzx http://www.mcmaster.com/#91116a160/=uytx5p http://www.mcmaster.com/#6661k82/=uyu075 http://www.mcmaster.com/#93070a177/=uytzsh http://www.mcmaster.com/#90710a120/=uytze4 EDIT4: I am just about done designing...

- Make sure the extruder motor sits all the way in it's slot, and tighten the four motor screws little by little. - Using the smallest 1.5mm allen wrench provided with the printer, reposition the extruder gear to align with the wheel on the Lever...

For this part there is no mount for the 9V battery, and the battery will just need to be hot glued to the base, the Potentiometer and the Pushbutton should push in, and then need to be secured by glue to prevent them falling out. **Hubble Lamp 2...

By self-printing corners and mids and using 30mm PVC Angled Edge Moulding, you can rigidly mount Corotherm and get a bigger (& lighter) enclosure for little or no extra cost. Corotherm ticks many boxes: light, highly insulating (for both heat and...

You need to be able to adjust the timer to on and off by the second. For example I have my pump run for 20 seconds and then I have it off for 1 minute and 30 seconds. <a...

Important: Modifications made by the user may compromise the warranty of their machines. The owner is entirely responsible for modifications to his printer. The initial idea was to couple the two 4020s to the original TTBluer case, however it has...

9,5cm diameter 8,7cm high printed in 14 pieces (base, top, 6 bars, 6 panels) no need of glueing (but it's safer to hold it by the bars when moving, especially when tealight or candle is inside) you can additionally lock the bars with a thread (tie...

It's supposed to fit over the battery mount and be secured by 4 5mm bolts of appropriate length with a washer on the mount side. (This will need supports everywhere, not just touching the build plate) but you can play around with the print...

When you've got the time to waste and a 3D printer sitting idle you use a cheap 6mm laser (less than $10 for 10 pcs online) which is badly aligned and poorly focused, print this thing and do the alignment by hand. It's only 4g of filament (1.43m...

The main problem is that there are now 8 potentiometers and by default Arduinos have only 6 (except the MEGA, but there is no way you can fit it here). So in my version I used a CD4051 to demux the 8 potentiometer outputs into only one ADC input. ...

Using the EMT between the arches is optional but I find it helpful for getting perfect spacing (5' sections by cutting 10' sections in half) and for offering a solid place to secure (zip tie) any power injection or LED signal wiring. However,...

I first saw the idea of using washers with a specified measurement from one of Germany's best leather craftsmen, Jürgen Volbach, who also explains how to use them in the video in this Facebook post and from or through whom you can also buy very...

Road Runner, a cartoon character in the Looney Tunes and Merrie Melodies series of short films produced by Warner Bros. Road Runner, also known as Beep Beep, speaks only with a signature "beep beep" (sometimes misheard as "meep-meep") noise and an...

This can be done by inserting a nut into each of the slots on the side of the Case Front and Case Back, so that the sides of the nut are parallel to the sides of the slots. Then, line up the holes on the Case Sides with the mount holes on the Case...

To tap the camera mounting holes (there are 3 each side, you can tap all or just the ones you want to use), I start with the same #66 to start the holes, then a 1/16" drill in a pin vise followed by an M2 tap. If you're stingy and don't want to spend...

By any means you are now scared to do this operation, I highly suggest you ask someone with expertise to help you on your endeavors.You have been warned.Step 1: partsFirst you need Noctua nf-f12 for the psu and Noctua NF-A4x10 FLX 12v Version.you...

this was my attempt to make something that would allow me to add more 6mm rubber tube to my adderini that i have converted with a ball bearing magazine by hakker mann to shoot 8mm ball bearings. i love the adderini platform an have made 3 at this...

The receptical for the battery is based on a project by "fcauwe" on printables.com called: "Mobile power supply (DPS3005) with black and decker battery (freecad files included) "...

... mean DXF files because Thingiverse can not deal with DWG files)</i>. All of the referenced files are the exclusive work product of the author and placed into the Public Domain by the author 24 April 2018 without any warranty expressed or implied.

The holes are spaced 115mm apart, in the center of slot height-wise -Nothing poking out in the back is included in the measurements, nor are there any feet on the case by default. That's it I think. If you have any suggestions, corrections or...