table saw and router 3d models

A simple magnetic base for a cheap dial indicator I got from Princess Auto for precise fence adjustment on a table saw. https://www.princessauto.com/en/dial-indicator/product/PA0002970986 I use 2 magnets from Amazon. ...

A small stick for a dremel table saw (https://www.thingiverse.com/thing:670704). This is just v1.1, as there should be multiple designs. I've realized the handle is tough to maneuver with, but that will get fixed in v2. If you have any questions,...

... across the flats (nut was measured at 10.91), with the printer's hole shrinkage taking up the rest of the space. I needed this knob to be less than 25mm in diameter as anything more would obstruct material pressed against the fence on my table saw.

It features multiple attachment points for the miter bar, allowing it to work with most any table saw equipped with a standard 1/2" miter slot. I created it to fit the gauge I purchased specifically, but the other hardware is universal and should be...

This is because I stripped out the thread in the aluminium casting of the table and installed M3 Rivnuts which sit proud of the surface. I can't imagine they'll be a problem if you haven't done the same. -I cut my riving knife down to the exact...

A tool that simplifies the process of cutting kerfs into wood when used with a table saw. Especially helpful for repeatedly cutting kerfs of the same size. There are many kerf-makers available here on Thingiverse, most with a similar design. One...

This is a gauge to set the height and angle on a Triton workbench saw with the heights being; * 5mm * 10mm * 15mm * 20mm * 25mm * 30mm * 35mm * 40mm * 45mm The angles are 30, 45, 60 and 90 degrees. ... I glued in four 8x3mm neodymium magnets so it...

In order to reduce the greatest possible dust load on the saw blade lifting gear of the GTS10XC and to avoid premature wear, I have provided this with a protection. Disclaimer If you print this model and use it, you do this on your own risk. I...

Replacement insert for old Rockwell 24" scroll saw. This is for my model 40-440 saw. Might fit others. ...Rockwell part number is LBS-56.

I bought the Kreg PRS2100 Precision Benchtop Router Table and installed a Triton TRA001 Router. At this point I realised there is no quick and easy way to shut off the power to the router in an emergency so I decided to fit an emergency stop button.

A router bit holder for 1/4" CNC router bits and another for holding bits still in their manufacturer's cases. ... Edit 10/17/19: Added a Collet holder to the collection.

Also you must shorten the bar to 192..212mm.For mounting the scale bar you need to drill and thread two M5 holes:Use slider2 with its prolonged side to accurately space the hole not to near to the table - otherwise the saw can not fully tilt back to...

Ultra precision table saw blade height gauge allows setting absolutely ANY blade height with extreme precision. Be sure to click on the [Download All] button so you get the necessary .PNG files in addition to the .stl for the plastic parts. If...

... the ages. Its robust legs and weathered surface speak volumes of the countless hours it has spent supporting the weight of freshly cut lumber, bearing witness to the rhythmic cadence of the saw as it cuts through the wood with precision and care.

The Betterley UNA-Gauge is specifically designed to measure and assess the accuracy of a router table's squareness. ...It ensures precise and correct alignment, leading to improved performance and better results in woodworking projects.

The nut from the original post was too big for my saw so I redesigned one based on the dimensions of the miter slot on my saw.After that I decided that the featherboard itself was a bit short so I lenghtened it by 5mm. I also increased the diameter...

Multiple size ring inserts for Craftsman router table with 2 inch opening.

22''x42'' fixture plate for a cnc router table .5'' holes at 2'' spacing

An adapter to connect my vacuum cleaner to my DIY would router table.

Router Table Insert Plate for Scheppach HF50 - Suitable Sizes: 12mm, 22mm, 47mm

The 63mm ID has provisions for an m6 nut and a m6/25mm wing bolt for tightening. This is designed to fit the dust output of a Makita MLT100 saw. The other 99mm OD end is designed to fit inside the stock end of a Metabo SPA1200 dust collector. The...

Work in Progress: Update 6/16 - The feather board connector 02 is modified to fit more securely into the HF saw slot and accommodate stock screws that came with the HF / Chicago Electric feather board. A washer was required to make v01 work with the...

I've taken the liberty of generating router table inserts for my Bosch RA1181 Benchtop Router Table, and I believe they will also work with the Bosch RA1171 Cabinet Style Router Table. This design draws inspiration from OEM inserts with tabs that...

This part fits the Rexon BS2301A band saw perfectly. ...The slot is slightly narrower than standard, making it easier to work on smaller parts.

70 mm table insert for multiple brands. ...5 mm thick.

I wanted a zero clearance insert for my DeWalt DWE7485 jobsite saw and printed another I found online but it didn't fit my saw very well so I set out and whipped this one up. The insert fit well enough and was fairly straight forward to level with...

That allows for good dust collection while most of the router table is empty and no fence is in the way. It's designed for an insert-thickness of 9 mm. However, I included a .step file to modify the part quickly. ... In this video, I briefly show the...

That allows for good dust collection while most of the router table is empty and no fence is in the way. It's designed for an insert-thickness of 9 mm. However, I included a .step file to modify the part quickly. ...In this video, I briefly show the...

Upgrade the original fence to keep the square, just change the two pieces of plastic that are under the fence and will keep the fence in square. Before using it double-check that the screws don't stand out from the print otherwise they are going to...

Upgrade the original fence to keep the square, just change the two pieces of plastic that are under the fence and will keep the fence in square. Before using it double-check that the screws don't stand out from the print otherwise they are going to...