textured cinder block wall 3d models

 Since I rotated the split for the duct 90deg (and split the left/right evenly) it directed the same amount of air to both left/right ducts.Important Tip: Before you install this duct, please make a careful inspection of the inner duct...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

There's versions of almost all of these with or without M6 throughholes for permanent fixture (or for attaching other stuff on top or something) and versions with straight walls or a 5° tilt to press the workpiece down towards the workbench. Often...

3 perimeters should be ok, but I recommend putting more walls around the screws using a modifier in the slicer, especially if you plan to skip on washers (seriously, just get some washers).It is highly recommended to pair the MMU with a filament...

Print it with a wall thickness of 5 and top and bottom thickness of 4 layers. 0.1 mm resolution. 100% infill. Supports yes.<br>2) The fins. Select the smaller fin for a 0.5 l bottle and the bigger fin for a bigger bottle. Print it 3 times with 0.2 mm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.Suspension Mounting: Pendant mount fixtures hang from the...

Hope you enjoy! Print Settings Printer Brand: Prusa Printer: MMU2s Supports: No Resolution: 0.3mm and below Infill: .2 and above Filament: any petg recommended, pla okay any Notes: Printing Tips: Level Your Bed: Follow your printer manufacture’s...

YMMV. grbl Settings (YMMV) $4=0 (step enable invert, bool) $5=0 (limit pins invert, bool) $6=0 (probe pin invert, bool) $10=3 (status report mask:00000011) $11=0.010 (junction deviation, mm) $12=0.002 (arc tolerance, mm) $13=0 (report inches, bool)...

There's versions of almost all of these with or without M6 throughholes for permanent fixture (or for attaching other stuff on top or something) and versions with straight walls or a 5° tilt to press the workpiece down towards the workbench. Often...

When printing, I seal the box by inserting a short length of PTFE tube (~25mm), with it's inner diameter sealed, into the open Pneumatic Connector. To make this, you need to print: 4 off Spool Holder Corner 2 off Small Box Bracket (only if you intend...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 shape =...

Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by removing the set screws that hold the bracket to the mounting bracket and adjusting the fixture. The fixture can be adjusted at...

You can do finer adjustments to the tolerance by putting some scotch tape or masking tape on the inside of the shell wall. Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to...

Ceiling and wall applications are mounted using the included adjustable swivel mount bracket found on the rear of the unit. Pendant applications are mounted from the ceiling and are suspended by rigid pipe via the 3/4" NPT hub on the back of the...

The EPL-LED-150W-RT offers an adjustable mounting system that this fixture to be mounted to any flat surface including walls and ceilings.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected...

4+ walls, 5+ buttom&top layers, 40+% infill is recommended by VORON team. If you want to save some weight, try different parameters in non-structural parts with your own experience. MODULES Afterburner (base) Drag chain link cable management module...

One way to work around this is to print extra walls behind such overhangs to reflect the airflow back towards them. In most cases this will be unnecessary however, but keep it in mind for those prints that need to be really perfect. (Someday I might...

you should have the fasteners to where you can pull, but it can't be pushed in (disassemble by pulling hard on light fixture if needed)bottom 4 corner pieces, and 4 frame parts (build box around lampshade base)install 4 frame parts vertically- in...

###Printing instructions - Material - ABS/PETG/Flex - Nozzle - 0.3 mm - Layer - 0.15 mm - Infill - 40% - Top/bottom - 5-6 layers - Walls - 4-5 layers Use raft and supports, see proposed printing layout on picture **printing.jpg**. ###Assembly...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = .8 height = 15 mirror = Yes shape =...

12v to 5v converter 5v power supply from wall I use LED strip lights Main power relay for printer I use that because it's reliable and easy to replace if needed. A short USB Cable A case for the Raspberry Pi with room for wires and cooling...

Note that the laser tube is behind this wall so be careful. Mount the camera using four 16 mm screws and lock nuts and you are done. ...Follow the guides in Lightburn to align and calibrate your...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

All the inflatables need only need 714,061 Liter (or 0.71ML) to fully inflate, so that is some extra air for the crane.I ran the program (PressArchAnalysis) that was used in the "Feasibility of a Self-Erecting Shelter with an...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

The AMS colour changes work effortlessly, and I am able to start a print with the external spool in a matter of seconds.Print SettingsMaterial: PETG (optimal) - PLA (best)&nbsp;Layer height: 0.08mm (optimal) - 0.12mm (best)Walls: 4 (highly...

Successfully tested 90mm/sec (45mm/sec for outer walls) without degrading a print quality. Drawback: reduced printing area to 210x210mm -> might be crucial to someone, but not that important to me. Also, I am considering some re-design of the right...