things y 3d models
1470806 3d models found related to things y.thingiverse
Customized version of http://www.thingiverse.com/thing:74322 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=74322
thingiverse
Instructions Forgive the code; I've printed and am using the product so I'm lacking enthusiasm for code cleanup :-) Print the object Locate: 2 M3x16 bolts, 2 M3 washers, 2 M3 nuts 3.5 Loosen the y-axis stepper Open up the bottom of the 'bot. Unplug...
thingiverse
This modification for the Y axis was inspired by www.thingiverse.com/thing:6184 and uses the same brass tube to increase the distance between the bearings on the Y axis. My XY carriage was a bit sloppy due to one of the sleave bearings being loose...
thingiverse
Installation layers are as follows: Tensioner Part 1 Wood Y-carriage Tensioner Part 2 (simple flat plastic spacer/slider) Nema 17 motor I had a little blue locktite on the M3 bolts holding the motor already. I tightened down the bolts through the...
thingiverse
Tapa (case) de las bombillas de la maquina de redemtion "cats and mice" ó "annoying things"
thingiverse
After some research I realized that the 10x10x10 cube in not an accurate way to calibrate your steps per millimeter due to the fact that you may calibrate it to the 10 mm length but you may introduce a bigger error for bigger parts, therefore I...
thingiverse
This is a derivative of thing 11601. I modified the 2 end plates so that the rod holders hold the rod higher off the assembly. I also modified the center section for a stronger switch flag. The idler holder is modified for more clearance. the idler...
thingiverse
This is based on Kludgineer's laser cut Y-Axis design found here http://www.thingiverse.com/thing:21638. This is CNC cut from 1/8" aluminum plate except for the two rod mounts parts 5A and 5B which are 1/4" thick. The bushing holes and 8MM rod...
thingiverse
improved "Anet A8 Y-Axis Cable Chain v2 " you could close the cable chain with the little stick or open by remove it .. The snap in should work much softer. ... ( https://www.thingiverse.com/thing:1915486 )
thingiverse
... with my Thing-O-matic. ... Instructions Print Part Unscrew and remove top two bolts from front right rod cover Place bracket over Y-Axis idler bolt head and align with rod cover bolt holes. ... Hold nuts in recessed areas and screw bolts on tightly.
thingiverse
... area without catching. Instructions Print Part Unscrew and remove top two bolts from front right rod cover Place bracket over Y-Axis idler bolt head and align with rod cover bolt holes. ... Hold nuts in recessed areas and screw bolts on tightly.
thingiverse
The first alternative uses countersunk bolts and was created by Tunell: http://www.thingiverse.com/thing:11775/ The second is the derivative of this one by M_G that adds a layer of plastic under bolt: http://www.thingiverse.com/thing:14098...
thingiverse
Note1: It might help to drill some 6mm holes in the left side panel of the printer so you can access the bolts holding the left end piece to the Y-Carriage without having to remove the Y-Rods and Y-Carriage. I made mine at the Y-Home position for...
thingiverse
A combination of two Thing-O-Matic upgrade things: Y-Axis Idler Support Bracket for Thing-O-Matic The rod cover from Cupcake XY Stage Quick Release Kit
thingiverse
I used to use it for fine bed leveling calibration but it had two things missing for me, so here is a redesigned version of the same concept with, in addition and for our pleasure : Two layers thick. Just to make sure the first layer is indeed a bit...
thingiverse
I've modified this to allow a longer bolt and it now also accepts either a 16T or a 20T idler pulley (easier to get hold of these days) Theres another untested version with a support underneath to lift the idler. ...I'll fix the dimensions and update...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dfGJ7FBB7pN
thingiverse
Customized version of https://www.thingiverse.com/thing:3082083 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3082083
thingiverse
Customized version of https://www.thingiverse.com/thing:1672381 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1672381
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: basethickness_percent = 0.1 wall = 1 textstring = THINFS base_radius_add_percent = .1 RoundedBase = 0 shift_font_percent = 0.07 fontname =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1399029 Instructions Using the following options: Loop_size = 18 letter_1_space = 14 letter_3_rotation = 0 letter_3_space = 14 Rotation = 50 letter_1_height = 8 Loop_font = Chewy...
thingiverse
Customized version of http://www.thingiverse.com/thing:536486 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=536486 Instructions Using the following options: second_letter = O first_letter = Y
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=714444 Instructions Using the following options: fontname = Orbitron textheight = 10 RoundedBase = 0 base_radius_add_percent = .1 textstring = Y basethickness_percent = 0.1 do_shift_font =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=677959 Instructions Using the following options: neodym_2_diameter = 5.5 neodym_2_height = 2.5 link_level = text_height = 20 text = _Y build_shift = text_level = 10 small_heart_outline_level = 9...