tinkercad things 3d models

The clampbar has many different attachment points all over its surface to attach things to. Clip the clips over the posts to secure the whole assembly in place. If you want to take the assembly off, just remove the clips and pull off the clampbar...

EZ-TRIM Harness line Gen 2 is a revolutionary system to trim your harness lines while sailing : watch the video : https://youtu.be/t7izQPLgtv0 This is an upgrade of EZ-TRIM Harness line Gen 1 (Thing : 4520587), much thinner and lighter. And also...

But once interest started coming in along with great reviews from Geneva show event they went full-speed and changed it into something like road-ready model since public liked that very much - although it wasn’t fully decided beforehand on actual...

To do that, please install OpenSCAD on your own computer and follow the customizing instructions below or follow these in depth instructions. AttributionThe OpenSCAD script is based in an early version on the "Parametric Button Generator -...

However, one thing I wasn't satisfied with was not being able to print with a high level of detail due to the limitations of the stock carriage. To solve this problem, I decided to upgrade to a custom X-carriage designed by Josef Prusa and Prusa...

Choose the one that fits better for your needs:The Smallest / Pro comparison:Circle diameter: 10 / 15 cm.Arm length for wide (narrow) angles: 4.2 (5.3) / 6.4 (7.8) cm and double length*.Marks readability: minimum possible / good.Vernier precision:...

(Note: rollers with less roundness than .4 or .5 tend not to roll to well) About Archimedean spiral Code Archimedean spiral is adapted from the work of Justin Lin's as found on his helpful website "openhome.cc" specifically, the page...

The Idler wheels will need to be printed in ABS for flexibility, Tensioners as well for the strength, all other parts can be printed in PLA. Assembly of the tensioners is easy just make sure to fit a washer either side of the idler wheel bearing and...

Remove the spring tensioner (the thing that looks like part of a clothes pin) as well. We won't be needing that anymore. Pull the free end so there is no slack in the belt and take note of where it is roughly 3mm from the edge of Part 2. Remember,...

Long story short, the two slot sizes can work for more things than one would think at first. About sizeAs you see, basic size is 25mm metric (not the 25.4mm of an inch) and each stand has a “clutch” or clearance of 0.1mm by side; this will help you...

$6.18 each, $12.36 total - Lowes - 2x4 wood - $3 - Home Depot - Screws and bolts Here's the order that I assembled things in: Right Angle Connectors to 2x4 1. Measure 18" apart on your 2x4 and mark the hole locations. You want two wood screws for...

Once again I have tried to reduce costs as much as possible, there are metric and standard alternatives for some things to help out with penny-pinchers (like me) m6 x 35mm hex bolt (2) (no alternatives) These 2 hex bolts are used to connect the...

As this is for resetting the display, I made a short version that does not protrude, making it more difficult to accidentally depress.) Built in RS DesignSpark Mechanical, using the 'things' as mentioned in the remix section as inspiration and to...

Thanks go out to aubenc for the [knurledFinishLib_v2](http://www.thingiverse.com/thing:31122). If you could take a picture of an actual print, please "comment" and attach the picture on...

I've not used it loads yet tho so maybe i've just been lucky but the cool thing about it is it cost me next to nothing to make so i won't be super sad if time teaches me that it really is trash. If you don't have a mmu2s or something that pushes...

both worked fine 4: 5 mm drill bit to clean up the hinge hole (optional but makes things easier) 5: Small spring. I cut a small piece off of a biro pen<br/> 6: M5 bolt at least 45 mm long (i used 50 mm) with washers &amp; optional spring washers. as...

Summer is coming.My office is getting hot.I had a spare 200mm Phanteks PC case fan and decided use it as a desktop fan.I have previously designed and printed some “feet” (https://www.thingiverse.com/thing:4515078) to angle the fan just enough for...

The first thing to do is to connect to your Palette over serial. You can do this by using the Arduino IDE and connecting the Palette via USB to your PC. With it connected, please set up the baudrate to 115200 and newlines to be enabled. 2. Send...

A further remix of https://www.thingiverse.com/thing:1088238 with separated horns and good for no infill. Good to slice with PrusaSlicer and print with MMU2S. <img...

(See link below) Simply print as many of the arm pieces as you need to mount the camera where you want it. The IR LEDs are not used, instead their mounting holes on the camera PCB are used to mount the camera to the back wall of the housing with M2...

I'm still learning how to model things, but I have lots of ideas and I'll upload them soon! If you also want to make a tip to me, I will really appreciate it, and I'll think about continue making this stuffs 'cause I will know that someone likes my...

Make sure they are sized appropriately so you don't have excess bolt length extending out the back (as that could catch on things and cause injury).Insert cards and enjoy!  DisclaimerKeep in mind that you're making a card holder out of plastic wire...

Made for this frame.CoreXY Frame (v.2.0) by Lehaiver - Thingiverse&nbsp;You will need to take apart two CD Drives for the linear rail which the pen plotter slides on.&nbsp;Uses pancake motor and m3 screws. ...Rests on MGN12H rail...

The model is optimized for the connectors shown on the pictures.Super glue/cyano acrylate/any other transparent fast setting glue which adheres to your filament.Wire (should be thick enough for 700 mA and thin enough to fit into the carrier*: if...

I posted a thing here which explains how to do a flow calibration (https://www.prusaprinters.org/prints/79581). If you have done that and still find the sleeve is too tight or loose, then it may require some scaling or sanding.</p><p>Assembly can be...

For Deluxe upgrade parts or all hardware directly from me, head over to: https://charlesworthdynamics.etsy.com Trap Pedal Available Print your own Trap Pedal here: http://www.thingiverse.com/thing:1394639 Stay Up-to-Date via Twitter & Etsy Follow me...

# Summary You may ask: "What is this thing?" Well, in fact it is a replica of a Yellow Vintage Cookie Jar from the 70's (McCoy VINTAGE Pottery #208 Yellow Mouse Cookie Jar). Today it is more like a part of an internet Meme - it's a mascot of the...

Garage Set set part 3 : Nozzles box Keep your nozzles safe :) Print needed drawer UPDATE: U1 : Add Stop to prevent drawers fall when open Mount instruction : Put all drawers in place an slice the "Stop part" (red one in screenshots) in the box I...

Objectives Students will be able to: Define theoretical probability Define experimental probability Compare and contrast theoretical and experimental probabilities Apply theoretical and experimental probabilities Audiences This thing is set for...

We are at stage which will make it all perfect since our machine really gives great things out right on there, because your child and we have this fantastic machine together! Update: after seeing an interesting video made for a YouTube creator by...