tiny modelling

Please let me also know how you rate the design.Unfortunately, the uber fidget ring was deleted due to a design claim, so its no longer available.If you like it, you can check out the dual fidget ring:And the discrete (as in discontinuous/quantized)...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl, and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

Print the model as is for the Front piece and MIRROR the part Z axis for the Back part. Position the part on its back with the legs sticking up, then rotate to 45 degrees to make it fit on your bed. Print the Front (part)... Then print the Back...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

Any longer and you'll have to either modify the model or hold it steady by hand while screwing in the first few mms until the guide grooves engage. Any shorter and you'll lose variable length and have to use a tighter initial state for the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

If you face any issues and or have design improvements, please comment below. 3D Model FilesSince this platform does not allow me to upload the original SolidWorks files, I have uploaded them to GrabCAD. If you are looking to modify the file you...

... There are probably better options, but I haven't investigated yet. You'll also need a Radio control receiver (and transmitter) (eg a Taranis). The X8R receiver really is too big for this size model, but it was all I had here so that's what I used.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Also there is heavy variance in the quality of the PCB you source from various providers as such various tolerances are required.Prints in 30 minutes in quality modeNo supports requiredNo screws requiredClip on method to assemble itVarious clearance...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

None of these models should need any support, I try to avoid them if at all possible, but you will need to be able to bridge somewhat decently. I personally used Overture Easy Nylon, it's very stiff for a nylon that doesn't seem to creep and...

If you need help or want something scanned, send me a message here on Thingiverse or on my FB page and I'm happy to help, ESPECALLY for a good cause (charities, educational models, STEM stuff for kids, etc.). Tips work...

and using less material) The idea is to print the markers in a different colour using the "Filament change" script (under Cura, M600 gcode, if supporter on your printer); you may also use the standard rotor-cover.stl if not interested by this version...

Perhaps my specific model of the C270 camera had some differences? - Original "c270_hinge_M3_screw.stl" was missing a crucial constriction of the bore for the pin (as viewable in the original camera mount). The edge of it should form an inner lip...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

1.2Runtime counter placed to keep track of the working hours/on-time of the Laser. The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20This box will fit in the enclosures made by Stepcraft.Hardware:DS...

My O scale model train layout represents the section of the Pittsburgh & Lake Erie Railroad between McKees Rocks and Youngstown. This wall section (stretcher bond brick pattern) will let you assemble a background flat of the McKees Rocks...

They are press fit and held by friction only and on my prints are very secure, they snap in pretty securely but can relatively easily be removed by getting a nail in the seam then wiggling. How I Designed This I created this because I wanted to have...

Heavily inspired by some images from 2008 i came across on the net i have been wanting to 3D model and build this for many years. I've been working on this for nearly 2 years in odd moments when i have time</p> <p>Update2 &gt; uploaded the cosmetics...

Merry Christmas! You will need to print: 4 ea Whirligig blades 3 ea Eccentric cams 2 ea Crossbars 2 Reindeer 2 ea Base Couplers 1 ea all other parts There is a cutaway view in the thing files called cutaway view.pdf showing how the model goes...

WORK IN PROGRESS Modeled off of reference pictures, many dimensions are guesses. This is intended to be a NON-Firing, but bolt operable, replica. can be printed entirely in PLA (if possible, the charging handle and magazine spring is better...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...