tmnt action figures 3d models

I Figured Out How to Do That Without Having to Re-Do the Design From the Start, and I Made That Change. Specifically, Where the Form Contacts the Print Bed the Clearances Between the Rings Is Not 0.4mm Wider, with That Extra Clearance Tapering Back...

I'm not sure if the red strip really does anything here, but I figured it won't hurt. Now glue the strips on the aluminum profile and leaf 20mm on one and 15mm on the other end. Also leaf enough space to solder and connect the LED strip to your...

Liberator weapon from the classic BBC TV series Blake's 7 Print instructionsA bit of background to this model. For those wondering what this is, in the 70's the BBC produced a sci-fi show called Blake's 7.  In it the crew of rebels/freedom fighters...

More plastic means more weight, so I figured it might be an improvement.As with the source model, 70% infill added a decent amount of weight and 10mm magnets were all I could find.SAFETY AND FITTacks: The holes in the model hold the tacks really...

The z-driver usually drives two stepper motors, so it is set to a higher voltage by default. Once you figured out the desired voltage you can calculate the required resisance using the voltage divider calculator. Just remove the 15kohm and set the...

Until I (or someone else) can figure out why you'll have to use OpenSCAD 2019.05 (https://www.openscad.org/downloads.html) to customize this. Based on play0r's really nice dominion box designs (https://www.thingiverse.com/thing:4696563). I love the...

V745 Labeled In the figure (pictured above) showing the new 3D model of the explosion, the blast wave is yellow, the mass ejected by the explosion is purple, and the disk of cooler material, which is mostly untouched by the effects of the blast...

... versions of the curb where needed for cross walks/ramps. <em>You will need to mirror some of the tiles in your slicer to get the full use out of these tiles.</em></p> <p>Bus, Fallout Shelter, Bus Shelter from M3Studios. Figures from Modiphius.

However, I was able to make each tray support its own science die (including the larger one that comes with Arts &amp; Architecture) plus an extra set of combat dice for each player.This was a beast to create, and I am hoping someone clever will come...

It will take some time and fine tuning to figure out the best settings and fan speeds. **FUTURE WORK** I am working on a better duct system. This takes some thought and consideration into what the best design will be. Maybe multiple types of ducts...

I make no promises that it will be sized right for any 5-pack of 1¼" fuses, but my suspicion is because the Eaton Bussmann fuse pack has been around for so long (there are lots of people on eBay and other aftermarket marketplaces selling empty packs)...

I used a figure 8 pattern to weave the lights down the tubes, however, I am considering putting the lights inside of the tubes to further eliminate any single point light sources. About 3/4 of the entire length of lights should be used on the top...

... speed of the fan or what type of fan is up to you. AIO MOUNTING WITHIN THE CHASSIS, This has not yet been figured out by me and I will devise a solution to this problem when possible. ... Dimensions: Length: 210mm Height: 34.5mm Width: 90mm

The new FPV-Rover V2.0 https://www.thingiverse.com/thing:2952852 This is a remix of the drogerdy designed by timmiclark. http://www.thingiverse.com/thing:700835/#files Upgrade 01: http://www.thingiverse.com/thing:1269962 Upgrade 02:...

&nbsp;If you have the proper filament colors, no painting is needed.The assembled model is 280mm tall.Updated 8/22/2021Somehow the head was uploaded incorrectly (I cannot figure out how it happenned). &nbsp;So, &nbsp;head_fixed.stl replaces...

This low poly rigged figure, while perfect for poser, was never designed nor intended for 3D printing, but I've had a burning desire to rectify that and turn it into a high-res prototype toy.\ I have put on hold many of my other projects to focus on...

i wired cables with respect to the polarity of the psu, (on the ender 3 pro the fan should be 12v BUT i double checked it by watching on the psu fan lable, because putting a 12v fan on 24v power out a fan will destroy it) 8.i figured out how to pass...

I managed to repair my existing part and I already purchased a replacement anyway but I figure parts may be even more difficult to come by in the future. This plate should fit either an Evader ST or an Evader EXT (ST Pro owners, look here: <a...

In the past for these puzzles you have to first figure out how to put the two tubes together by following the maze. Then you had to reverse the procedure to separate the two tubes. This resulted in working the maze twice. In my design the tubes go...

He saw Akio as a father figure, though the merchant held little care for his orphaned guard unless he successfully avoided an ambush on the road. Though a cat’s senses can’t always be sharp, and while nursing a hangover one morning, the young master...

Last i tried printing 100% out of Tenacious, with the springs attached, the ski's were bowed upward, i could twist and bend the ski's in any direction easily and figured these would definitely not break, but they did! So i went down my own path...

Update 01.02.2020: bean protector grill and cleaning basket were updated for easier use and more washing volume. Cheap cure wash (CCW) module V1.0: As a SLA printer operator, you quickly figured how annoying and messy post processing of prints is....

When shapes of figures are defined by curves, only three tools are used: Extrusion Boolean operation: Difference (in order to cut out) Fillet edge (on the animation you just see the unfolded menu) Nothing more... Objectives: A basic approach of...

Some puzzle makers craft this puzzle out of wood, and it is said that the puzzle is so difficult that solvers sometimes resort to examining the grain of the wood to figure out how the pieces fit together. Are you up for the challenge? Classroom...

For a start, I used the same kind of18650 with flying leads that I use for my lightsabers, and I just figured that if anyone wanted to make my MKI adapter, they'd just go out and find a flying lead 18650 rather than use regular 18650s. That was...

This design needs a lot of tweaks to be optimized for V2 see “Needed Changes” Needed changes for Version 2: The following list details all of the needed changes/stupid mistakes I made during the final assembly process/hail mary style build to make...

 If you use this in a stock dome, you will need to figure out a solution for powering these LEDs yourself (you might be able to drive one from the original Radar Eye LED connection to the motherboard, but probably not both). PRINTING AND ASSEMBLY...

I spent a good bit of time trying to figure out the best arrangement of openings for wiring, and settled on "can't have too many", so there's a lot. I'm working on a plug design to close ones that aren't being used, but so far they've not been...

&nbsp;I suggest gluing in the Bugs figure (body_gray/body_white/body_gray_extra/hand_right already glued together) into the hole at the same time as you glue the hole_black and brown together.4 - The holes for the whiskers are symmetrical but for...

I've found a way around a lot of the hard stops of the limitations of space and dimensions, but still haven't figured out the recoil system...though I have some good ideas about how to do it. And I still need to make a trigger! But you can see the...