token holder 3d models

A filament spool holder with filament runout sensor is in the works. September 16th, 2020 Update: I've added a file named "Base Plate(no dd)" for those who don't want to convert to direct drive, shave a few grams off the weight of their X...

It would probably also work with the Mod-S version.For easy switching use the MMU2 PTFE holder PC4-M10 mod. This is what enables quick switching from one RMU to another by just switching the set of RMU output to MMU tubes and running through the...

An alternative to printing this is to use 10mm tube instead. Other Hardware Parts needed Trigger Spring 6x20mm or 8x20mm long should work Magazine release Spring (approx 5mmx 10mm long) M2x12 (quantity 3) self tapping screws (for catch hinge and...

I've also printed out a small battery holder for 2 AA cells (Thing 2339441), as an alternative source of power for when USB isn't available. I am planning to modify the design further. Partly to get rid of the lightwell, and partly to provide a...

The base parts are:1) Base (BaseV1.STL)2) Flat Base (FlatBase.STL & FlatBase-NoHoles.STL)The garage wall parts:1) Front of the garage (GarageFront.STL)2) Buildind side wall (GarageSideWall.STL)3) Building back wall (GarageBack.STL)4) Front wall...

And what use would a bit socket be without a…Bit holder - it fits a standard bit snugly, but just in case it wears out with repeated use, it also has space for two magnets that should keep the bit in place.MORE MAGNETS - extra four holes for magnets...

It was originally meant to just be a place holder part, but it has been included anyway as an extra choice for people. Think of it as a budget option for your army. The Turret T2 is mostly unchanged, save for some minor dimensional changes and a...

If you print cleanly, the imitated terminal block fits perfectly into the bottom of the shuttle - alternatively you have to file it down a bit.First the angle was fixed to the wall, then the white base frame was pushed on, the black support on top...

I added areas underneath with M3 nuts to affix the belt holder into. Designed the x endstop with Fusion 360. Refer to the listed "remixed from" section for additional information. Custom Section BOM You will need either: 2x M5 Nyloc (or standard)...

The 4 larger holes on the very top of the main case body are for heat-set inserts; the 4 larger holes on the face of the main case body, where the PSU holder mates with it, are for heat-set inserts; and the 4 larger holes on the lid that the fan...

Check it out here: http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Here are some instructions to follow: I used the following options in this custom design: gear tolerance set at 0.1 the number of faces for each object is set at 32...

Finally, if you forgo using the included card holders, you can use these to raise the rows behind other rows, pretty much exactly like the original cardboard stand. Print one of each of the 8 files. If you turn each half of the lid upside down in...

This was my first hurdle and I attacked this by moving the bottom seat of the rod holders in towards the center by 6mm on each side. To help the smaller “left” gantry I added some small extensions that wouldn't interfere.</p><p>&nbsp;</p><p>I tried...

1x TP4056 charging module - Link 1x 18650 holder - Link 1x Momentary push button - Link 1x Illuminated rocker - Link 1x 400kV pulse module - Link 1x 18650 cell 4x 20mm M3 socket cap machine screws 2x Nails Some wire Basic soldering...

Next is a Bomber edition with 1102's. So far, I've only printed the frame with with Sainsmart Carbon Nylon filament, which is light weight, and pretty tough, but by all means, try out different materials and share the results. Design may be updated...

... marks of LEGO Group. Star Wars, the Star Wars logo, all vehicles and character names of Star Wars are registered trademarks of Lucasfilm Ltd., Disney, or their other respective trademark and copyright holders.Timeline 11 September 2023first version

A little force might be required, and when viewed from the outside should fit snuggly at the bottom groove.M3x10 screws can be used to ensure it stays in place, but I found it wasn't needed.The Stepper Driver and RTC module each has a plate that you...

Customizing the capsule holder (number 0 in the files) is very simple. In the images you should easily understand the assembly method which is however very intuitive. Those in yellow are rubber bands (very soft) that must be adapted in length and...

When installing the driver, make sure that the driver is installed in the correct direction, the pin marking EN must be on the top left !!!!I lost the first TMC and the Arduino on the first try because I slept !!!!Since Thingiverse absolutely wants...

Glue or screw the servo arms to the acrylic parts. When attaching the servo arms, make sure they can turn enough to reach every point on the drawing surface by manually turning them Power the arduino, it should start a calibration cycle where every...

Use supports where needed.Main body doesn't need any supports.Print all front and back suspension pieces in 100% infill to have the best strength.Sand down and or drill out holes to have the suspension freely running.Hardware:Mostly M3 screws, works...

2 washers at the top and 2 at the bottom between the bearings and nut holder were used.\nIf you get to this step I should have more photos/instructions showing the rest.\nMORE NOTES:\nAny place that a pulley attaches to a bolt, screw on a nylock...

Therefore, I created two of the same case parts for different board thicknesses: a) Electronics 1,5mm PCB.stl -> for 1,5mm thick PCB b) Electronics 1mm PCB.stl -> for 1.0mm thick PCB Other files: body.stl -> main body, holds the cell and runs the...

The headset rests on two extrusions of the main holder. The controllers are hanged on the arms. The main part can either be wall mounted or mounted to the foot. The foot has canals for cables. The main part in turn has room for cables within the...

Perfect solution also comes for any standard large optics (spotting scopes included) that is waterproof too - meaning nothing stands in between you taking that amazing 4K photo right away, at night on distant mountains as you watch them being shot...

There are a few ordinary boxes that have been created, but I set out to create a functional box to intelligently organize the game pieces. The tree can be set in his holder as is, but there are 4 openings around the tree that were designed to store...

A filament guide is necessary to use the knob on the Ender 3 if you have your filament holder on top. FIX (02/10/2018) Thanks to user wonkoderverstaendige I found out there was a tiny (but real) problem with the file. Basically the knob floated a...

UPDATE 05/24/16================== Created a new handle for the rig, plus cable holder to keep the wire nice and neat to connect the button to the phone. Also updated the lens slider. Overall some improvement but still not happy with the handle, its...

To complete the connection system you will also need (INCLUDED IN MDS PRODUCTS): - MDS_TRACK_CLIP_Standard (To connect track parts) - MDS_TRACK_CLIP_Pianos (To interconnect pianos) - MDS_TRACK_CLIP_Lanes (To fix straight lanes in parallel) -...

I tested it out and it seems good, but to stop the weight of the cables plugged into the dock pulling it back I used some Command Strips on the bottom of the dock holder to keep it in place. Bill of MaterialsRequired:- 3D printer and filament (inb4...