uhf mount 3d models
348330 3d models found related to uhf mount.thingiverse
Simple UHF mount, the base is 120x120mm with multiple mounting holes. have included a fusion file as well so you can alter the dimensions if required. Thanks, Enjoy! ...
thingiverse
... Magnetic mount for Mazda BT-50. ... Reuse original mount hardware. Use double-sided tape to fix to vehicle. ... Sits flush with profile of AC area Initial Prototype (may need more surface area for adhesive backing tape) Paint when finished.
thingiverse
awesome original, remixed it to suit a tx3100 and an external speaker
thingiverse
Added April 2015 - radio-mount-bfeng.stl Instructions radio-mount-bfeng.stl has hole for a DIN-6 socket. DIN-8 should also work. There are holes for flower nuts for the DIN mounting screws. These are the smaller M3 flower nuts - about 4mm across. I...
thingiverse
This is based on Mochaboys QAV-400 UHF Antenna bracket: http://www.thingiverse.com/thing:152510 I made this to mount my Dragonlink v2 Rx underneath the battery tray. ... OpenSCAD file included.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/8dExav75yWV
thingiverse
The scale is fine when i drew it up in fusion. However printing the sizes went abit hows it going. ... The base i scaled to 102% Fusion files added, if edited, upload as remixed so i can see some other designs.
thingiverse
Added a switch extension device which makes the transmitter balance correctly when using the Ext2 version of this mount, a DLV3 and long antenna. Attach the switch extension using 2 3mmx10mm machine screws. ...5/03/2018 Added extended mount for DLV3...
thingiverse
This thing is a UHF Antenna Mount for the X-UAV Mini Goose (Snow Goose). The mount is designed for an antenna using R/C antenna tubing with an O.D. of about 3.2mm. The circular mount fits into the top rear of the fuselage where a GPS is meant to go.
thingiverse
Designed in OpenSCAD and used to mount my UHF Dipole to my QAV-500 quadcopter.
cgtrader
A mount which allows me to mount my radio onto my paraglider. It uses the radios beltclip to attach to a 25mm tube. Both straight and 45 deg mounts are here as stl. Both have channels embedded into the mount for zip-ties. ...
thingiverse
A mic holder clip for the car that is used for pretty much most UHF / CB hand held PTT microphones
thingiverse
Resolution: 1mm Infill: 20% Rafts: Yes Supports : Yes Radio Unit Mount: Print Orientation: Print with clip gap facing upwards Resolution: 3mm (for speed) Infill: 20% Rafts: Yes Supports : No In-Vehicle Handset mount: Print Orientation: Print with...
thingiverse
Used to provide a mounting point for the counterpoise of a dipole. Use 1.2mm derailleur cable for each element and cut to 158mm. For the driven element, this dimension is from the point where the cable leaves the end of the shield. The counterpoise...
thingiverse
... and removed the sticker, yellow foam grip and drilled out the rivets for the threaded tip and removed it. ... Note that in the pics it is not mounted, just mocked up, and the cable is not connected.
thingiverse
Whipped this bracket up to mount my uhf radio to my lifeproof/Ram ipad mini mount i have for my vehicle. I didnt want to use two brackets so this was my solution. ...
thingiverse
Ham Radio Operators may appreciate this: This is a very simple print which I designed because I needed to put a UHF/SO-239 barrel through the wall of my metal trailer. The trouble is that the trailer has a lot of electronics in it, some of which...
thingiverse
I made adjustments to the original by Liquify_life to fit the hand mic on my Yaesu FT-212. It needed to be thinner for the hand mics I have. I also decided to shorten it, as I did not need the height, and found that I also did not need the back part...
cults3d
It's mounted at an angle so you don't point your null towards the craft Also very conveniently leaves clearance to change any module you may have under it Needed: 2x m3x12 2x m3x10 Make sure the screws are tapping their own thread into the plastic,...
grabcad
General RF connector for use in electronic design
thingiverse
A water resistant case I made to replace the stock Summit RX with a UHF rx.
thingiverse
The current release of EVA 3.0 doesn't have a provision for a BL Touch in combination with a Rapido UHF nozzle. ... In order to accommodate for the additional reach, I mounted the BL Touch on the bottom end of this mount with some M3 screws
thingiverse
I built the module holder part to go along with this thing: http://www.thingiverse.com/thing:101766 The fit on the 3 finger mount is pretty tight and may need to be sanded. Printing all pieces will give you what I have pictured, everything to...
cults3d
This is an adapter to mount a UHF module (or other things) to a Turnigy 9X radio, there's also a dipole antenna holder that can be plugged either in the adapter or the antenna hole of the radio itself. It uses three M4 X 15mm bolts for the adapter...
thingiverse
This is an adapter to mount a UHF module (or other things) to a Turnigy 9X radio, there's also a dipole antenna holder that can be plugged either in the adapter or the antenna hole of the radio itself. It uses three M4 X 15mm bolts for the adapter...
thingiverse
These are cradles which hold the DTF-UHF OpenLRS transmitter modules and use the arms and JR modules from Jason Wratten at http://www.thingiverse.com/thing:101766 . There are two cradles, one for the older pre-Hawkeye DTF-UHF module and one for the...
thingiverse
A cradle mount for Handheld Uniden UHF Radio. ... Mount it anywhere with double sided tape
cults3d
A quick-to-print template to ease drilling, marking, or mock-up of where to place an SO-239 UHF chassis mount connector. Customizable as well (sizes if you'd like, but you can also remove the tab with the drill size reminders (which is largely there...