ultimate gps breakout v3 3d models

\nEarly Magellan Roadmate GPS devices used a “T-Slot” socket to mount the device to dashboard, windshield, cup holder and other mount locations. At some point in succeeding models, the “T-Slot” was replaced with a 16mm ball mount that can accept...

Wait for a few seconds after the GPS LED begins blinking, then press the button to hear the clock speak. ...Finally, secure the board to the rear panel with four #4-32 x 1" pan head self-tapping screws and attach the rear panel to the front using...

GPS MOUNT: With a 41-42mm wide space, this mount is perfect for housing a 4s 2200Mah battery and holding the GPS antenna on a 20mm round platform. It weighs in at 10g with 25% infill for added strength, and comes equipped with a convenient handle...

GPS MOUNT: This design provides 41-42mm of space for a battery of up to 4s and 2200mAh, while also securely holding a GPS antenna on a 20mm round platform. The entire mount weighs in at just 10g when printed with 25% infill for added strength, and...

Instructions This is a compact housing that I built around a Ublox NEO-6M GPS receiver based on the one sold by Unmanned Tech in the UK. Update 11/08/2014: Some extra space was added to the parts so that minor over-printing issues wouldn't keep the...

Easy-to-Assemble Base Unit for Arduino Nano Breakout Board

New-style Baby Breakout enclosure for Atomic Pi.

Vive Breakout Enclosure With Mini DP Cut-out & Scaled

Time Of Flight Breakout Board Project Case Capsule

Needed a GPS mount for my Radiolink TS-100. Had used the original re-mixed source circular mount with double-sided tape for a while, but it came loose. Designed this one in Fusion360 and it snaps firmly into place while staying fairly...

The Clarion MAP770 is a sleek and feature-rich GPS device designed to provide an unparalleled driving experience. With its intuitive interface and robust navigation capabilities, this unit offers drivers a wealth of information at their fingertips.

We wanted a simple solution for mounting our new GPS system, especially since it features a useful backup camera. It turned out that placing it here wouldn't block anything important or require additional holes to be drilled. This spot has worked...

Cutting-edge GPS technology comes in the form of the HGLRC M8N, boasting a clever relief for the connector and wiring to prevent damage. This innovative feature is further reinforced by 3M tape, keeping it firmly in place. For optimal performance,...

The phone rests in landscape position for optimal GPS viewing, and a convenient access point on the left side allows me to plug in my power cord. This design ensures an unobstructed view of the road at all times. With a few simple modifications, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=415391 Instructions Using the following settings: Thickness is set to 1 mm Cable Hole Width is set at 10 mm Cable Hole Height is precisely 4 mm Mounting Centers are exactly 20 apart Over Depth...

"Avengers' Time GPS", an innovative navigation system crafted by Tony Stark to explore the quantum realm and retrieve the Infinity Stones across time. Discover this cutting-edge technology in our Etsy store! The device features adjustable straps...

Edit it online at https://www.tinkercad.com/things/5WDaslPuVCT The case cavity should fit any 25mm x 20mm GPS Module. If you need to modify the case in Tinkercad, make sure to ungroup the bottom part before scaling so the pin dimensions will not...

This is a straightforward and effective universal solution for holding phone/GPS in the car's air vent. The adjustable width accommodates phones and phablets, ranging from 56mm to 92mm (equivalent to a rubber band). As such, most devices should fit...

The Lezyne GPS Bike Mount has been reworked with some tweaks to make it easier to print in 3D. I printed this mount using PETG, but you can try other filaments - just be aware that PLA might not work so well. A 50% infill is a good choice for maximum...

This is a dedicated platform for a GPS tracker on the Mavic, utilizing 3M Dual lock to secure it effectively. To ensure added stability, consider incorporating a tie wrap as well. If the tracker features a key-ring type hole, similar to the TK-Star,...

Custom Section Design Considerations The GPS mast mount on the HobbyKing S-500 quadcopter is notoriously fragile, to put it mildly. Mine shattered immediately when I tipped the aircraft over, prompting me to create a sturdier alternative in DS...

This is a GPS mast for the GEPRC MK4 frame. I needed to got the module above all the electronics but didn't want an ugly carbon rod. Printed in TPU at 35% it feels rigid enough to stay true but also flexible enough it should withstand a crash or two....

This is a drop-in holder for the exelvan Q7, perfect for most cars that will hide the GPS screen from other traffic. Simply attach it to your dashboard with double-sided tape or velcro tape. My print is in PETG, which resists high temperatures in the...

... optimized designs that enhance the overall performance of these aerial vehicles. ...This meticulous process allows users to seamlessly integrate different components and create custom modifications, ultimately leading to improved flight capabilities.

This is an ultra-advanced Data Acquisition System.\r\n\r\nhttps://youtu.be/X3RiIEgv-_Y?list=PLW1IBsHOodG-cKctVMPX8WWRV_M8ycJtd\r\n\r\nFeatures: GPS, BME280, MPU6050 & microSD card module.\r\nLogs data as:...

Have a QLG1 GPS for a WSPR radio? Don't know how to separate it remotely from the radio? You now have a chance to give this a shot. The "back" side features a 15mm (5mm thick) "cut out" if you want to convert the QLG1 to use an external antenna,...

To do this, you can access the source model online on Onshape: create an account if needed at https://www.onshape.com/, then search for public models at https://cad.onshape.com and look for "GPS_holder_PM". Copy the model to edit it as desired. ... To...

This is a precise model of a GPS Satellite. It was originally created with 3ds Max 8 software. SPECS: This model consists of 47 distinct objects. The total polygon count for this model stands at 69155, when TurboSmooth is turned off. However, with...

This design is a GPS L1 square patch antenna with an embedded LNA, available for public use without permission. Electrical specifications include a band of 1575.42+/-15 MHz, peak gain at boresight of 4.6 dBi, selectable LHCP or RHCP polarization,...

This is a custom 3D printed case for the GPS Clock project on Hackaday.io. If your clock has the long green post tactile switches, you'll need to swap them out for FSM4JSMA switches or trim the posts. Boards with these switches are coming soon to the...