ut99 models

Printing horizontally for increased strength meant the tube experienced a little shrinkage (9% horizontally, 1% vertically), so I made a bigger model (Tube_40mm_account_for_shrinkage.stl) that accounted for this shrinkage, which worked...

A very good model from Velrock. Yet another remix pose Time-lapse print video : https://youtu.be/xsk3FDa-Cx8 Baby Yoda : https://www.thingiverse.com/make:872409 <iframe width="560" height="315"...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! unscrew PSU from the frame remove plastic cover of PSU cables ...

Description: https://youtu.be/G9-N-nIqc4g Assembly: https://youtu.be/2hdSGDdjpeQ Torque Capabilities Please note that I designed this CVT for a demonstration model, it's not intended to be used as an actual transmission. How This Works - Watch the...

Once I print and test it, I will update this with the final model and the STL's. I'm currently working on a new version with a removable tray for the Pi since I now plan to use a Pi4 with this project. I would not recommend printing this until I can...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

V1 arm is fine too, but there is a risk of collision with some models of head in very rare cases of high and wide prints prepare all parts power off the printer UNPLUG POWER CABLE! disconnect low voltage connector (2 wires) unscrew PSU from the...

In my models are embossed labels A, B and C for easier assembly.&nbsp;Length A is 350 mm and you will need 30 piecesLength B is 398 mm and you will need 44 pieces (45 if you want full dome without entrance)Length C is 500 mm and you will need 10...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

For now I have modelled two trailers:mk14 flatbed trailer for general loads, 10' and 20' ISO containers.mk17 tray-style trailer with hydraulic crane. Can carry 1x 10' ISO container, or general loads. Tray sides are removable.mk14 trailer can also be...

The diameter is 50mm, 23 teeth, pitch 2, height 20, slop .01.Updated threads were created using Fusion 360 and then incorporated into the Tinkercad models. &nbsp;Several versions were tested at various tolerances to get just the right fit across...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

- An increase of thickness from 0.5mm to 0.6mm, which should allow a wider variety of resolutions and nozzle sizes to print the design and make the end-products more reliable between printer models. Thank you again for your support and enthusiasm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The bell is modeled after a large bore 8.5 inch symphonic bell, fitting a Bach 42 or Bach 50 slide, and possibly other brands as well. It's designed to work with a PVC slide, which can be replaced with any type of tube by editing the .scad file...

The battery negative is connected straight to the Anderson PowerPole negative and the radio negative.The model includes a plate to put on top of the batteries to ensure nothing gets in and shorts them out.To make the antenna fit inside the box with...

... for a few days. Dry the hoses and just press the printed belt clip and connector plug into the ends. Lowes Item #879263, Model #98620 https://www.lowes.com/pd/EZ-FLO-3-8-in-Inner-Diameter-x-10-ft-PVC-Clear-Vinyl-Tubing/1000365031 Category: Costume

[Medium Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   Raised as a commoner, Artorian never expected that one day he would rule from the divine seat of the Nirloom that soared so high above the streets he grew up in. Some would call...

Not wishing to disassemble the printer, and even less to change the direction of rotation of the cooling fans of the LCD screen, I wanted to model a filtration system requiring no modification of the printer. The power supply of the fan is carried...

Start printing the parts (some of the parts need support).After you finish printing the Base, Hinge and the Main Stick you can start assembling the parts (use this 3d model for reference) , then insert the potentiometers to they're spots and wire...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

This is my third Core XY conversion kit for the Ender 5 with Linear rails. Previous versions here, updates at the bottom of the page. MK2: https://www.thingiverse.com/thing:4777606 Mk1: https://www.thingiverse.com/thing:4650517 As per the previous...

What's IncludedThe entire Anvil Digital Forge Patreon release for November 2021, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

Make sure you have enough spare belt before you take anything apart, or order one. The existing nuts and bolts and acme nuts from your existing printer. 2 additional Right hand 3/8" -12 Acme nuts (http://www.mcmaster.com/#95155a111/=ovvhbk) 2...

I modeled this in Fusion 360, and you can find the source files as well as IGES included. I printed it in PETG since that's what was in the printer. The infill was 30% with three solid layers. ... Print Settings: Printer Brand: MakerGear Printer: M2...

In Cura, this can be accomplished by selecting the model, duplicating it, and then choosing `mirror` and selecting the red and green arrows. `Langstroth Frame Top 2 piece.stl` - **Print 1x, 100% infill, Duplicated per instructions** This piece is...

I designed around MD3DD’s BL Touch model and CAD data found in manuals for V1-V3. Being posted for over a month and over 250 downloads with no makes or comments, I assume all is well and have removed the Work in Progress status. ... Take a look at...

Some special thanks to Alessandro Virdis for the belts lock model provided. Every single piece made this a beautiful work of different minds ;) It is a 3D printer with 300x300x300 mm printing area, powered by a Lerdge-S with Cr-2020 or Duplicator 6...