valve index base station mount 3d models

It's a belt-clip to hold your Index controllers on your waist and can also be used without removing them I designed this to be used with VR Golf Club, but I am sure it can be used in other applications. If you want a left side mount, just mirror in...

This is a remake of my old Thingiverse project that I made after breaking my rear cable clamp on my well used and beloved Valve Index: https://www.thingiverse.com/thing:4424259 Unfortunately that cable clamp, even while being more stable then the...

... and DXF (2D) project files are included in case the tolerances need to be loosened for your printer. Stay tuned for alternate lens adapters based on Zenni frames shaped more like the Index lens which use metal frames that are easier to disassemble.

The first thing that went wrong with my much-loved and frequently used Valve Index VR headset was the rear cable clip. Next was the upper pin that holds the cable in place, followed by the cable itself (pixel snow, occasional cracking sounds,...

https://www.etsy.com/uk/listing/1065848597/valve-index-minifan-dual-fans-frunk-mod?ref=shop_home_active_1&frs=1** Before you continue please read: I am not responsible for any damages that could occur from bad wiring/soldering, I use my fan mod daily...

Use the standard ball fastener that came with the base stations to attach it to the mount, then route the cable through the large slot and secure it behind the clip on the underside of the mount for a clean look. If you need to adjust the angle of...

Easily placed on the front of a Valve Index to enable a very small amount of airflow through the VR headset." - Maxxgold My Remix extends the original 40mm by a switch. It is a mystery to me how to use this without a switch, so I made a remix on the...

After many, many revisions, I'm pretty sure I've come pretty close to a good take on a gunstock grip design for the Valve Index Knuckles.And they don't need magnets!The grip part that you hold on to is made to be as thin as I could make it, to...

For Valve Index owners who want to use the lowest IPD setting (58), a significant issue arises when bringing the lenses towards your face to increase the FOV as high as possible. As you move the lenses in so far, your nose will inevitably rest on the...

Here is a nice Tripod mount for the antenna on the ProfiCNC Here+ RTK base station. This is a press fit and will snap into place with the proper dimensional print. This has an Arca Swiss plate for tripods with an Arca Swiss mount. There are 2 tabs to...

This is a remake of my old Thingiverse project that I made after breaking my Front cable attachment on my well used and beloved Valve Index. https://www.thingiverse.com/thing:4424259 Unfortunately those front clamp, even while being more stable...

**I do sell the finished product on my Etsy store!https://www.etsy.com/uk/listing/1047496097/valve-index-dual-fan-frunk-mod-set?ref=shop_home_active_1** Before you continue please read: I am not responsible for any damages that could occur from bad...

Under the capacitive sensors in the Valve Index controller lies a pressure pad. Using a 3D printed 'paddle' designed specifically for this purpose, you can simulate the grip action in game by squeezing the paddle on the controller's pressure pad. By...

So, just print and assemble these simple base station mounts if you want more easy and freedom regarding the placement of the base stations. The Onshape project is here:...

If you've purchased the HTC Vive Prescription Lenses from VROPTIKER.DE and wish to utilize them with your Index, simply take out the lenses from their cases with care and insert them into my custom-designed adapters.

A simple visor derived from the official Index CAD models, made so mods can be easily screwed on in different positions. ...The holes will take M3 or 4-40 screws, so as long as they're shorter than 5mm.

I had a kit of Tyre Valve Caps for wheels placement prior to wheel/tyre change (vinter - summer) but symbols were printed and not enough visible. The original does fit loose on tyre valves and came off very easy. I have googled around to see if...

This adjustable offset allows you to fine-tune the position of your Index headphone speaker, shifting it by up to 5.4 degrees inward or outward as needed. ...Whether your head is narrower than average or wider, this adjustment ensures optimal sound...

# **Mounted Handle** Mounted handle is based on this: https://www.thingiverse.com/thing:4195091 It needs 2 m4 screws and nuts for the hinge and bracket closure. ... **The Good** - Handle feels like a handle, because it is away from the controller **The...

This adapter plate enables you to mount HTC Vive Base Stations onto a 16mm spigot found on light stands or tripods using the included wall mounts. The M5 screws and nuts supplied with the adapter can be used for attachment, but it's highly advised to...

I imported the model from Valve's official 3D Files into PrusaSlicer. ...I was suprised that this model wasn't already uploaded so people could print spares!<br><br>(My logo on the front is just a sticker, not part of the model)</p><p><a...

I've included a Tray insert that matches the Frunk pocket, along with the model file of the blank insert from Fusion 360 so others can build their own ideas based on it. To create the OLED insert, use .96"x.96" 128x64 pix OLED Displays and 8 m2x5mm...

adapter for index to HTC das, WARNING THIS IS NOT REVERSABLE (easily) DUE TO A METAL INSERT NOT INSTALLED IN PLASTIC ON LEFT SIDE OF HEADSETneed to salvage from the old headstrap:2 metal disk like inserts (important, see image for what it looks like...

... it's too tall. I only used heat shrink tubes to insulate the connectors. I recommend unscrewing the Index's main cover plate and drill holes in it as shown on the photo. This greatly improves cooling even when not using the frunk fans at all. ...

Assembly includes slotting the two mount halves together with two printed joints and screwing into your wall with appropriate screws. If you're concerned about the plastic scratching the hmd, you can glue some cloth down to cushion and provide...

the recommended magnets are so strong you only need to bring them with in 5cm of each other and they will line up and join them selves, the index tracking system doesn't like shocks so you will have to practice so you can control the reattaching of...

I was experiencing an issue where my ear speakers were quite loose, so I put together a quick o-ring based on a reddit thread's idea to increase the friction with an o-ring.ID: 9.6mmOD: 13mmheight: 1mmflat square o-ring type

... importantly off the floor). To mount: You'll remove the "Uplift Desk" name tag on the left/right side of the desk. Then use 2x M4 bolts and nuts to attach. Print with whatever settings you think you need. ...I used: .32 layer height 25% infill

... importantly off the floor). To mount: You'll remove the "Uplift Desk" name tag on the left/right side of the desk. Then use 2x M4 bolts and nuts to attach. Print with whatever settings you think you need. ...I used: .32 layer height 25% infill

... hole etc. ... Made so you can use any cable, plug it into the controller and just slide into the stand. All edges have been beveled (90º Edges are sharp, please guys, bevel your edges). The base is flared/wider so it does't tip over as easy. ...