weighted companion cube 3d models

Minor evolution and refinement of the 50mm design. I decided to test this design using one of the best direct drive extruders available in the 45mm world - the Bondtech MK2-MK3 (full kit) upgraded extruder made for Prusa:...

I recommend Ø 3mm metal rods, as they give the game board a little more weight.44 washers Ø 9 x Ø 4 x 0.8 mm (metal, plastic or self-printed). It is important that the washers are not thicker than 0.8 mm, otherwise the spaces will be too narrow and...

Finally place the coaster at center, with the weight of a cup/bottle it will stay in place but you need just add a few drops of glue to insure that it wont leave it's place. ...As a further improvement you can add a bit of cork to the coaster to better...

* Wall Thickness: Another important measurement in object designs, wall thickness decides the structural stability and weight distribution of parts. Adjust it to meet project goals with its default value being 1.6mm. Options include offset, gap, nut...

The human foot also has the ability to adjust to changing pressure and weight distribution, ensuring that we can maintain balance and stability even on uneven or slippery surfaces. The human body is a remarkable and intricate machine that continues...

Attention: the plate uses parameters from the bin section and vice versa, so when using the customizer, first set all the parameters, then render one object after the other and don't mess with the parameters, until the whole set is rendered,...

Skeletal muscles are attached to bones and enable voluntary movements, such as walking or lifting a weight. Smooth muscles are found in the walls of hollow organs, such as the digestive tract, and help to move substances through the body. Cardiac...

Additionally, the standard design offers ample space for integrating a wireless charger directly or adding weights to enhance stabilityESPHome Code available on my GithubParts NeededRotary Encoder with ClickESP32 Module (I used ESP32-C3-Supermini)M2,...

Mostly 3D printed, full size and fully functional Short Shaft outboard motor equivalent to typical 2hp petrol engines but without the weight, mess, fuss, noise and emission's. This post is for the Leg 5 upper leg section only. The main files and...

Total weight so far with base and 2 motor covers is 775g. Added: bottom plate, plan is to use 20mm long 4mm bolts through the side plate that traverse the entire hole in the motor shield and then retain the plate. It works but is a bit of a pain to...

Having little to no sculpting talent of my own, I am very grateful for the talent and generosity of the designers whose work I have leveraged here.With a little "cut and paste" help from 3D Builder and MeshMixer, I made the following adjustments to...

I made some tweaks to enhance the part and also attached both the .stp file and the .stl file for your remix.I did a few enhancements as detailed below and in the pics:Added a viewing port to see the nozzle during print.modified the right mounting...

We had a problem with lighter (less infill) hubs because they would "float" out of the center hole, so we prevented the hubs from floating with a small dead weight on top of each hub. We did not use a vacuum chamber to de-air the silicone. We did...

Basically it uses the two original top screws that hold the glass in the case, and keeps some support along the back side of the screen, while having a 10mm block at the bottom to help support the weight of the screen. The block sits between the...

You need to have friction between the lever and the slot so it remains in the position you put in otherwise its own weight will bring it down. 8) Work your way up until Case #1 9) Solder the wires to the Arduino and connect it to the computer...

The basic general thickness of 1.67 mm should work with most plastics.Orientation: Side on printing bedTo make sure that the weight of whatever you put in the hook is pulled by the material itself and not the layer lines, my hook should always be...

Design inspired by an other model available here → https://www.printables.com/fr/model/198721-toilet-tank-bleach-tab-holder/comments DesignFrom Fusion 360 I designed a simple rectangular block that was extruded and drilled with several holesI...

I came up with an easy solution that snaps in on the side and the weight of the spool holds the arm in place. Then I mirrored it and now even have two. The plexiglas piece on top of the hood I just switched with the plexiglas on the back. I love...

I've also doubled the arm sections up to: a) take more weight at extension, and b) Add rigidity, although single sections can be used if you prefer, as per the original design... The arm sections are 'handed', one having a recessed M5 nut hole...

Because of this potential heat, and the weight/motion of the chain itself it is suggested to use PETG over PLA. Atomic Filament's Carbon Fiber PETG is great, durable and adds some stiffness to regular PETG. The part attaches to the motor by replacing...

I wanted to create an unibody mount in order to reduce the screws needed and the set weight: - For Sidewinder X1 v4/Genius, choose the BMGAero_mount_adapter (heat resistent material and extruder stepper Vref setting to 0.6V is highly recommended). ...

The resistance should be enough that the boom holds up under its own weight on any given position, but not so much that you will pull the crane over every time you want to move the boom, scrape or sand back the little bumps on the inside of the...

Hollow CF tubes helps keep weight down: CF_fitting_half - takes a 8mm carbon fiber tube. Best if it is 8mmx6mm CF_fitting_half_75P - takes a 6mm carbon fiber tube. Best if it is 6mmx4mm Put a small bead of glue around the outside of the top of Wing...

Supported Browser: Supports Chrome and FireFox Supported File: SVG and DXF are supported Accessories: Protection glasses, USB cable, AC cable Power: AC100V Size: 910820380mm Operating Temperature: Below 30C (86F) Continuous Operating Time: Under 30...

2022-02-18: v1.4 updated start scripts and factory files 2022-06-01: Added improved 202 fan spinner for APC prop ASSEMBLY MANUAL AND USER GUIDE FLIGHT VIDEO: 1st flight: 2021-12-14: https://youtu.be/5a5afEyBsjc Print time: 85hrs Print weight: 125g...

If we want the hot glue to hold an considered amount of weight we need a lot of it. A lot of area on the print to be glued to the wall should do the trick. You the the three big ass triangles with a bit of support structure? Just pour hot glue on...

It is good to have it sliding to adjust position of the wheels along the frame and then adjust the weight on the ball joint to get full shocks movement. If you don't care, choose the best look position and glue.or screw. The upper parts are 60mm...

I prefer the lower set as I rest my arms on my desk and palms on these surfaces and this allows my arm to contact the desk more vs make my wrist take the weight of my arm. I wrapped my palm wrests with 3M Carbon Fiber vinyl wrap. Got off EBay for $7...

It is good to have it sliding to adjust position of the wheels along the frame and then adjust the weight on the ball joint to get full shocks movement. If you don't care, choose the best look position and glue.or screw. The upper parts are 60mm...

Because the Ender 3 has only one Z-Axis and we are adding weight to the moving hotend with motor and extruder we wanted to provide additional support to the Z-Axis lead screw. Now there are a lot of Z-Axis bearing based retainers out there however...