wight got 3d models

"Can I save space on my shelf by storing expansions in the main game box?" ...unfortunately (depending on how you look at it) I got somewhat carried away, and things just ballooned from there! The original inserts for Lords of Waterdeep have...

If you got creative, you could probably use fishing line or something similar to tie the two together through this hole after assembly. * The GPS antenna holder was designed against my board, and the little notch is supposed to "clip" underneath...

Watch out for the following sizes:0.35x75mm or 0.4x75mmI got a whole bunch of them here: https://www.aliexpress.com/item/1005001467649993.html How do you print it?I used my Original Prusa MK3S with MMU2S and some modifications.0.2mm layers,...

IntroductionMy office chair and me…..is a long love story !I got my office chair, a Sitag Reality more than 20 years ago when my father brought it home for me from his company, after their local HQ had relocated from one building to another one. It...

Rig made with add-on rigify, included with Blender 3d Animations Goat: get_hit, goat_attack_1, goat_idlegoat_idlemover_idle2, goatformidlerungostackruning_gotatkackl_l_sword_right_lefant_r_leftlefant_l_ightleft_atlack,...

If you get one with different solar panel dimensions, let me know. https://www.dollartree.com/garden-collectiondiamond-textured-black-solar-stake-lights-14-in/302600 I got the idea to use a dollar tree solar light for a fence post from CHEP on...

A video is here https://youtu.be/46ky7EqzZt8 When I finally got it assembled, I didn't like the big gap between the block and the intake manifold. So after spending some time looking at similar RX7 engines for sale on Ebay, I designed coils, a...

His documentation and instructions are extremely well done and were very straight forward to follow.https://create.arduino.cc/projecthub/arnabdasbwn/crazy-engineer-s-drawing-robot-arduino-grbl-corexy-drawbot-fb5269There are very few (and very cheap)...

I got carried away and fully closed a box that was full. had to destroy the box to get the pieces out again. If it's too tight, look for areas that might be sticking out (On the race boxes specifically, I always had one corner on the tray that had a...

 Get that wrong, and you WILL burn out your MagicBand+, as there is no reverse-polarity protection circuit. I recommend a digital multimeter to test your leads before you run power, if you want to make sure you've got the polarity right...

I hope that some of you can take this and improve it, I am excited to see what you can do with this.As I got in to 3D printing a few months ago my wife decided to get in to miniature painting. We happened to have an extra Ikea Trofast (small) shelf...

This version is one piece, so four hours and a heck of a lot of support structure later, you've got this thing that will safely hang your Bose QC35 headphones without "pinching" the soft headband layer. If you love wasting time and filament on...

 (My concrete porch left a rough surface finish, so instead I got a cheap granite surface to pound the stamps/rod against.  Whatever you choose, do realize that you will be repeatedly whacking it with a sledgehammer, so make sure its...

I was able to cut five stacked sheets at once without difficulty, so I got thirty strips from one stack. If you don't have the cutting equipment, it works fairly well to carefully tear strips since you're going with the grain, but it's much slower. I...

Edit - 18th September 2022 - Got my extruder working again now so I have done a test print.  That has resulted in a couple of tweaks, mainly for fit.  I've made the trigger thinner to let it move easier (now 5.6mm instead of 5.95mm).  I have also...

If you got creative, you could probably use fishing line or something similar to tie the two together through this hole after assembly. + The GPS antenna holder was designed against my board, and the little notch is supposed to "clip" underneath...

A good way is to look for companies' clearances and liquidations.One day, I found out a Mitutoyo roughness meter SJ-210, which I got for 300€ by auction while a brand-new device is sold around 2500-3000€ here. Good deal then ! The only issue I had...

 I had NO idea how to do this when I got the idea but loved the challenge. Printing Instructions:There are three parts- The Body, The Print-in-Place Gear box and the Tongue/strap.  All were printed at .2 layer height. My best successes...

I got LED strips from the brand Grundig there. Cost of the LED strip is about €10.In the meantime I have switched to the following LED stripe because it is much easier to glue (I only use superglue at the entrance of the...

I got LED strips from the brand Grundig there. Cost of the LED strip is about €10.In the meantime I have switched to the following LED stripe because it is much easier to glue (I only use superglue at the entrance of the...

at a 2 hour party there were ZERO tears shed from getting whacked too hard, and even the parents got into it! 2. Avoid Silk filaments for this of you are actively using them. Silk PLA simply does not have the bonding strength for the layers to...

value_array.append(final_vector) # Transform matrix now looks something like: 2x [[5.6e10 , -2],[8e16,-0]] where in column 0 (at 0 index), the X-coordinates got updated while the second remains at original positions and is left untransformed. ``` ...

Your drawing area would be something like 200x200 or 220x220, which could be enough to try to "print" 13x18cm images or maybe you decide to expand your Y axe to 30cm to be able to work in A4 size ;) My Stock Anet A8 mainboard got the bed heating...

It's not exactly rocket science which piece of string goes where (and you've got pictures to refer to after all), but if your string is as flimsy as mine, you're in for an experience. That's also where I messed up a bit. I should have left some slack...

I got LED strips from the brand Grundig there. Cost of the LED strip is about €10.In the meantime I have switched to the following LED stripe because it is much easier to glue (I only use superglue at the entrance of the...

So far I've got some feet, a center platform, a couple of spool holders, and some options for mounting filament runout sensors and badge reels. I've designed for 3/4" and 20mm square aluminum tubing as legs. The previous design for 1/2" tubing legs...

You can of course simply print 8x "mountingholes" but it will take longer (more contours). Added some position markers to help assembly when you're looking at the inside, so the mounting holes will line up. UPDATE V004 I finally got around to...

Whether for fashion-conscious or modestly-styled occasions, we've got something perfect for you. Our elegant Bangles feature bold and intricately detailed patterns. Bangles are made in various sizes with precise craftsmanship ensuring each piece is...

... batteries, change polarity if the LED didn't light up.</p> <p>Lastly, just push the lamp holder into the top cone interior, and fixate it with a bit of sticky tape. It will light until batteries got drained, however, that's enough for a great party!

I got LED strips from the brand Grundig there. Cost of the LED strip is about €10.In the meantime I have switched to the following LED stripe because it is much easier to glue (I only use superglue at the entrance of the...