xtool d1 pro z axis extension 3d models

ENDER 3v2 and other models Cover for Z axis stepper motor. ... Ive added a dual Z axis setup on my E3V2 so decided with 2 of them they needed covering up!

Didn't like niches in original z-axis stabilizer so I designed a simple cover to hide them.

The Ender 3 lacks a reinforcement for its Z-axis, which causes issues for some users. To address this problem, I designed a part specifically for the Ender 3 and the Ender 3 Pro models. This design is based on components available from Aliexpress,...

Yet another Z-axis stabilizer designed specifically for the Ender 3 or Ender 3 Pro models, this one breaks down into two easily assembled pieces. Installation requires the use of two M2.5x12MM screws and two matching M2.5 nuts to secure it in place.

Minition Beagle Camera mount for Creality ender 3 S1 Pro, upside down on the right of Z axis, without the original stand. ...Tensionner is still usableLet you see the bed, the piece and the nozzle.Middle part "entretoise" let you adjust verticality,...

A dual Z-axis kit makes the printer much more reliable and convenient, especially with the TH3D dual Z-axis kit (1). Later on, I adapted this kit to add a second Z-stepper motor, which requires moving the PSU. I wanted to keep the PSU mounted to the...

Simple coupling upgrade for CTC Prusa i3 Pro B z-axis original rubber tubing. The weak point lies where motors meet threaded rods, making it prone to failure. This straightforward upgrade secures the threaded rod to the motor shaft with a clamp. Four...

System was used to more precisely time and stabilze a motor driven dual z axis on a Ender 3 Pro. You need to get a sencond rod, rod mounts and x axis mount for this project to be integrateable. These were not included in the BOM, but can be bought as...

I'm aware that numerous mods exist to rectify the Geeetech Prusa i3 Pro B's wobbly Z-Axis, but I prefer to design and manufacture my own solutions so I decided to share my creation with others. To address this issue, I designed a replacement top...

It is based on the idea I saw at [Ender 3 S1 Z-axis Camera Mount C920](https://www.thingiverse.com/thing:5330674). This does not include the standard 1/4-inch mounting screw. I also printed one from Thingiverse:...

This is a printable attach point for a cable chain supporting the extruder cord. ...It attaches to the Z axis feed motor with the screws already in place.

Didn't want to give up my handle just to install a Z-Axis stabilizer, so I mixed them.

Liked the designs and uses his other knobs but he didn't have a Z-Axis/Rod knob so i made one! ...

The optical endstop Z mod for Creality Ender 2 Pro for better keeping Z-offset (mechanical stock enstop works for me poorly) Uses TCST2103 (RepRap Standard). ...May be it suitable for Ender 3 too (not tested)

It all depends on the time 😄---Reinforced part to fix the "Nema 17" motors of the Z axis on Creality Ender 3 S1 and S1 PRO printers as well as for other printer models that use a 40/20 aluminum extrusion profile.I created this reinforced part...

The Z-axis of the stock is wobbly because the stepper motor side is not held in place by bearings. This modification adds a 608 bearing to the Z-axis to eliminate the wobble. ...Also, the bearing holder on the upper side of the stock was eccentric, so I...

I liked the aftermarket Z-axis stabilizer by p1mrx, but the front mounts didn't fit my Ender-3 S1 Pro, and the rear mounts were too unstable. I redesigned the mounts to fit my frame (which appears different from the one the designer has), and added...

This upgrade is designed for the Tevo Tarantula Pro, stiffening its Z-axis and reducing deflection caused by a bent leadscrew. It was created to print quickly without necessitating a complete redesign of the TTP. This upgrade is compatible with...

Z axis anti wobble nut, Ender 3, Ender 3 Pro Это единственная работающая модель на принтерах Ender 3, Ender 3 Pro не мешая шаговому двигателю, и нет необходимости что либо смещать и передвигать, не требует ни каких дополнительных покупных материалов,...

... smoothly onto the rod, winding the Z-axis up with ease. It won't lower the Z-axis back down, instead backing off of the rod, but that's not a big deal since 99% of the time I need to adjust the Z-Axis is to lift it out of the way, not lower it down.

Only tested with KP3S PRO S1 that has Y-axis linear rails and not v-wheels. This modification requires removing the power supply to attach extension screws to the side of the printer. But to remove the power supply's screws you need to remove the...

Ensured the nut end was tall enough to prevent the z-axis linear bearings from sitting atop the fingers. Refrained from recessing the nut into the bottom plate, opting instead for a flat mating surface. My printer had difficulty producing a level and...

imprime sans support

Its really a huge difference at high speed because at the right of the z axis it move a bit in Y axis You need a ender 3 for parts Something to bend or cut metal Equipment for soldering OR The complete kit cost 50$ on site like amaz0n 15$ @liexpress...

This was a concern for me as I don't want the bed flexing as more plastic gets added to a print. Many of the Z-support designs avavilable require that you dismantle the entire Z-axis to insert them. I designed these to just slide into place. ...You need...

NEW VERSION: https://www.thingiverse.com/thing:4857627 ==================== Anti-wobble for z Axis for Ender 3, Ender 3 pro. --------------------- This is remix of: https://www.thingiverse.com/thing:4759091. Stablization magnets were moved to...

- Optional but recommended: Z Axis Bracket (left & right) with printable bearing, enclosed the M6 printable bearing. Advantage: - M6 threaded rod is more flexible, won't affect X or Y axis as much as (bent) M8 threaded rods. - M6 gives 1mm pitch...

Carefully install the z-axis rod stabilizing bearing by first disengaging the coupler at the bottom of the rod. Then, gently push the bearing into position and slowly lower the rod back down. ...A friction fit should develop as you slide the bearing...

I designed this stabilizer for the shaft of the z-axis. This is canceling swinging. ...The bearing is very stable and there is nothing preventing it from turning.608 Bearing,2x t-nuts,2x M4x12 screw,2 M2x5 screw, If you think that the bearing is stable...

Here's a top plate replacement for the Z-axis that I had to replace because mine got broken. This part was designed with inspiration from a real-world object. It's specifically made for the right-hand side. ...If you need one for the left-hand side,...