zero tolerance 3d models

I have not modelled any clearances in these holes as I prefer to drill them out post printing to get the best possible tolerances to achieve the most rigid mounting. This mod is designed to use M3 x 4.4mm diameter x 5 mm long brass inserts...

I printed as large carabiner as would fit on my printer (X2.2), but since the tolerances doesn't scale I included this "fun sized" carabiner among the files as well. For some printers, the gate might need to be lengthened (by ~2%) to close properly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

What You need to kow is that I use a tolerance of 0.1mm. Meaning the inlet for the QR code in the frame/case is in x and in y direction 0.1 mm wider than the actual QR code itself. This way they will fit in perfectly togehter and hold by friction. If...

The gears also have about 0.1mm contour shrinkage (0.2 backlash setting) to account for printing tolerances. Printed at 0.3mm layer height they work smoothly with no backlash for me.\r\nLarge gear. A 45 tooth gear with a pitch diameter of 67.5mm. A...

But hey, that is the reading you need to see, dont fool yourself with a resonance graph taken on a wrong place.Regarding the printing and assembly:for the printed parts you have to use a well calibrated printer, because the design is not forgiving...

Depending on your printers tolerances, you might need to sand the plugs a bit to fit.Finally top it all of by setting the head onto the glass body and putting the cap (or the northern hemisphere) on the top.Preparing for the gamesSimple - fill the...

There are two basic styles that can be created: cylindrical and spheroidal.The design is 3D-printer friendly: no supports are needed except for spheroidal handles with really large X and Y dimensions (length and clearance) and a really short Z...

I don't have any myself and the tolerances are .5 mm from what was shared with me on their size but I'm told they fit great. 5/12/20: The paint brush shelves now have a guide built into them to fit together. The overhang in the bottom of the mid and...

It's a very hardy, low-maintenance plant, tolerant of pollution and drought, and is often used as an ornamental in gardens and parklands. Included in this Package: 15 models in total Standard -- 84,989 polygons -- 3.79m tall. Fully mature and in...

Changes since v3: Internal geometry free and manifold Tweaked angles and print orientation to print without supports Fixed inconsistencies in angles and slopes, and center points Removed curves in favor for bevels and beveled more edges like those on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance = 0.4...

The two seals are offset by 0.1mm to increase the tolerance range for sealing.(Sealing) Fitting of the seal receptacles reduced to 2.0mm diameter.(Drip) A sort of "vase" around the valve has been added, serving as a collection volume. Within this,...

Be very careful if you sand the surfaces (shouldn't be needed with a calibrated print) as you can open the jig tolerances and the cannon might not hold in place while it cools. Custom Section Tips - Using the jig Test fit the cannon in the jig to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

All can be printed at 3mm layer height, but the dial will look more pleasing if you use variable layer heights.The device needs to be as precise as possible, so I’ve deliberately made the tolerances tight to minimise unwanted movement. You need to be...

I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are good. radIn - radius for the filament radThread - radius for fitting If your fittings don't let bowden tubes go straight through, replace radPtfe =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance =...

Depending on the material, tolerance in your dogholes. Often the material has a tendency to be pushed upwards. The through hole versions mostly minimize this, but require M4 screws - The holes in the waste board are small and not very deep, in...

In addition to using a properly calibrated 3D printer, due to tolerances of adapters, if possible perform hot nozzle pass on all exterior surfaces, to reduce surface porosity for FDM based methods, otherwise SLS/SLA method preferred. Highly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

A heartfelt thank you for that :) Small problem though - the original design didn't fit the cheap 9G micro servos that I had on hand. So I spent asmaller amount of time optimizing the design to fit the servos I (and a lot of other people might) have...

This helps to tighten the tolerances and makes the floating deck float more smoothly. I was unable to exit games and go back to the menu without pressing the ESCape key on the keyboard. This was the reason I mounted the laptop with the keyboard...

Please send us a message if you are interested at twothingies@gmail.com  DisclaimerDue to the different properties of 3D printing filaments and the tolerances of different machines, you might need to scale up or down some of the print...

Depending on your printer’s tolerance, you may need to trim/file the recess back slightly to get a nice snug fit for the roof. • The pilings/stairs were similarly printed in one piece and then glued to the underside of the floor, (positioning...

I added some zip tie holes in the sides and improved tolerances. I made slotted holes because my printed X mounts changed the dimensions a bit. I have printed, installed and now used this part. Below are instructions on how to set it up. I printed...

Depending on your printer’s tolerance, you may need to trim/file the recess back slightly to get a nice snug fit for the roof. • The pilings/stairs were similarly printed in two piecs for this Hut (to accommodate it on my print bed) and then...

This might save you some heartache if you accidentally break one of the rings or mount it in the incorrect order.When the barrel is complete, simply pop it into its hole in the body and glue it down.Printing tips-and-tricksThe barrel needs supports...

Depending on your printer’s tolerance, you may need to trim/file the recess back slightly to get a nice snug fit for the roof. • The pilings/stairs were similarly printed in one piece and then glued to the underside of the floor, (positioning...