folger tech i3 3d models
64239 3d models found related to folger tech i3.thingiverse
This is a brace for a cooling fan for the Folger Tech i3-mega than points onto the stepper drivers. ...I modeled it around a spare 5015 blower fan that I had laying around.
thingiverse
Mounting plate for the folger tech i3 printer. The mounting plate holds the original mounting block that comes with the stock printer. It also has a built in holder for a 12mm diameter proximity sensor. The bottom holes have a indention in the back...
thingiverse
Check out all my Folger Tech i3 2020 fixes and enhancements at http://www.thingiverse.com/pjvpjv/collections/folger-i3-2020-improvements Print Settings Rafts: Doesn't Matter Supports: Yes Notes: Supports necessary, but super easy to remove. ... Print as...
thingiverse
This is a modified version of e-squizo's MK7 fan shroud with the vent extended down from 20mm to 27mm which works perfect on my Folger Tech 2020 i3. Follow his instructions for mounting, basically replace the fan with the shroud, then mount the...
thingiverse
Works best with the rollers designed here:http://www.thingiverse.com/thing:1708865 Print Settings Printer: Folger Tech i3 2020 Alum Rafts: No Supports: No Resolution: 0.2 mm Infill: 25% min up to solid Notes: Notes: Printed with PLA but ABS will work...
thingiverse
Print Settings Printer: Folger Tech i3 2020 Rafts: No Supports: Yes Resolution: .1mm Infill: 60-100 up to you Notes: PLA for stiffness. Triangle supports at 4 or 5mm. Print the LOWER part up-side up. Print the UPPER part up-side down. Make sure the...
thingiverse
Replacement chromed rod holder plate for the Folger Tech 2020 i3. ... Print Settings Rafts: Doesn't Matter Supports: ...
thingiverse
I noticed that the Folger Tech Prusa i3 kit doesn't come with any sort of filament spool holder, so I tossed together these. They fit on top of the printer and accept a 10mm rod. This thing was made with Tinkercad. ...Edit it online...
thingiverse
This is for standard Folger Tech Prusa i3 extruder (mk7 ???), fits a 40 mm fan. Apologies for the quality of print on the photo, my eyes bled too. Performance of this thing is so so as a standard fan is not designed to push air through such small an...
thingiverse
I took the spool roller from pjvpjv and added a 2020 T clip. This way no extra screw is need it to mount it. It should be presure fitted inside the 2020 T-slot. I also left the original hole so a screw could be fitted in case you have issues fitting...
thingiverse
Just wanted a little less cover for more airflow. ...Print Settings Printer Brand: RepRap Printer: Folger Tech RepRap 2020 Prusa i3 Rafts: Yes Supports: No Resolution: .2 Infill: 90
thingiverse
Print Settings Printer: Folger Tech 2020 Prusa i3 Rafts: No Supports: No Resolution: 0.2 Infill: I used 30% infill for strength. Notes: I tap the 2020 insert with...
thingiverse
... Direct fit to the stock carriage of the 2020 I3 Print Settings Rafts: No Supports: Yes Resolution: 0.2 Infill: 25 Notes: minimal support for the hex holes on part one Post-Printing Hardware 6 M3 nuts 6 M3 x 25 bolts 1 quick connect for teflon tube
thingiverse
This is an x-axis mount for an e3dv6 replacement to the stock Folger Tech Prusa i3 hotend. ... It is modified from this:http://www.thingiverse.com/thing:547706
thingiverse
I created this for my Folger tech Prusa I3 so that I could add the E3 V6 hot end without major modifications.I did remove the extruder cooling fan since mine did not get hot enough to need one. ... To get the best results you will need to change the...
thingiverse
This is an all-around cooling for Folger Tech Prusa i3 (MK-7 hotend). I assembled it and pretty happy with how it looks - have yet to print with it. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
... to keep the filament centered to the print bed. Let me know how it works for you in the comments. Print Settings Printer Brand: RepRap Printer: Folger Tech Prusa i3 2020 Rafts: No Supports: No Resolution: .3mm Infill: 100% Notes: I used ABS
thingiverse
I fixed the two issues I had with the otherwise amazing original design: (1) bearing rubbed against mount causing binding; and (2) my bearings were loose, so slipped off the mount. The built in washer prevents the side of the bearing from rubbing.
thingiverse
This is a Y carriage belt mount with integrated tensioner for the FolgerTech 2020 i3. It allows the belt to be centered on the bed rather than offset as is the one that comes with the kit. I also wanted to integrate some sort of tensioner and didn't...
thingiverse
Printed this user's chains but I wanted the chains on the back instead of underneath of the carriage. http://www.thingiverse.com/thing:921162 So I mocked up a mount for the heat bed which already has a hole predrilled. I used a M3 screw and...
thingiverse
Remixed TNSI's lead screw holder for the smaller 5 mm bearing (stock lead screws) Like above - one is with the 10.5 mm hole & one without Print Settings Printer: Folger Tech i3 2020 Alum Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2...
thingiverse
I got tired of the separate ways to attach this controller to the 2020 frame.. so I borrowed some files and redid somethings and came up with this..might redesign it in the future as I am printing it for the first time now. "FolgerTech 2020 LCD...
thingiverse
Modified the original X End Stop (left side) to have a notch for an X-axis belt tensioner. Belt tensioner: http://www.thingiverse.com/thing:872944 Used OpenScad to do this. Code: difference () {import("C:/whatever/Endstop_X_Support_Left.STL");...
thingiverse
This is a pair of rollers and clips to go along with this top mount:http://www.thingiverse.com/thing:590956 The clips were remixed from:http://www.thingiverse.com/thing:606006 I designed the width to fit all of the hatchbox pla/abs that I...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/if4nvMLJRnv This was meant to be used in conjunction with my filament guide found at http://www.thingiverse.com/thing:846329 .
thingiverse
Customized version of http://www.thingiverse.com/thing:605196 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=605196
thingiverse
I got this fan duct I use it. ...It works.
pinshape
... bed with an M3 screw and a tiny washer. Attached to the frame with an M4 and a T-Nut (an extra that came with the kit) Print Settings Printer Brand: RepRap Printer: Folger Tech RepRap 2020 Prusa i3 Rafts: Yes Supports: No Resolution: .2 Infill: 90
thingiverse
... bed with an M3 screw and a tiny washer. Attached to the frame with an M4 and a T-Nut (an extra that came with the kit) Print Settings Printer Brand: RepRap Printer: Folger Tech RepRap 2020 Prusa i3 Rafts: Yes Supports: No Resolution: .2 Infill: 90
thingiverse
... made a modification to MindRealm's clips of http://www.thingiverse.com/thing:606006 to fit Hatchbox filament spools. ...This fits 58mm wide spools. This clips into the Prusa i3 spoolmount w/ bearings by sigshojhttp://www.thingiverse.com/thing:590956