monoprice select mini v1 3d models
177949 3d models found related to monoprice select mini v1.thingiverse
This is an E3D Hotend Mount for the MPSM V1, it probably works with the V2 but I don't have one. There are two hotend mounts, one that has a DF 5015 Radial Fan, and one that doesn't. There are two clips on the left side of the mount, one is for the...
thingiverse
from the finished camera mount.https://youtu.be/RvZ2YVNDr94 Here is a time lapse of v1 printing from the stack of books the camera was on beforehttps://youtu.be/bXUUXomYZI0 I think I like the mount better than the stack of books it replaced ;) Print...
thingiverse
I scaled it down to the size of Monoprice select mini's bed. When this test is done, look at each square. They should look the same, thats the most important part. If the squares's infill looks sharp and jagged, raise the bed on that corner. If the...
thingiverse
I watched many videos on the upgrade of the Select Mini v1, and feared the day I would actually change out the original E3D holder. As it turns out, you do NOT have remove anything but the two end cap screws and the socket head screw that holds the...
thingiverse
Nearly zero-offset adapter to use e3d v6 hotend with Version 1 of the popular Monoprice Select Mini. Allows use of third-party e3d v6 hotend and nozzles to allow printing with larger variety of filaments. Since I used this with the e3d v6 hotend,...
cults3d
I liked the idea of the pi camera mounting bracket by stevepax and used it for inspiration to create this one for my GoPro. I ended up angling the shoe instead of the mount itself since it was easier to design. I have included two files, one is for...
myminifactory
After buying a used MPSM used for a $100 i quickly realised why it was so cheap. The Z-Axis bearings exploded and fused to the guide rods. After complete disassembly it became clear that I could not press out the bearings and that I should model a...
thingiverse
40mm fan shroud based on the stock design with added internal fins to direct airflow better
thingiverse
This is a long time project. I've had the MPMini for about 5 years now, it was my first introduction to 3D printing and it has a special place in my heart. I've upgraded it so many times, mostly due to my breaking the original hot end, and deciding...
thingiverse
I wanted to update my V1 Monoprice Select Mini with a dual nozzle design. I settled on this design to accomplish that goal. ...
thingiverse
But as I recently got my Monoprice Select Mini back up and running, I decided I wanted to re-mount the webcam to the Y-Axis traveling printing surface, for better timelapses and more useful monitoring of print quality. I imported mspieth's MPSM...
thingiverse
This fan housing was designed because i put a mk8 style heater block left over from an anet a8 onto my mini, the wider heater block was sitting against the stock plastic fan housing . This housing has around 8mm more clearance around the heater...
thingiverse
I took the original and slightly modified it to work with the MPMS V1. I haven't used it much yet but seems to work great so far. I also made the hole bigger for the V1 heat sink. ...Hopefully you find this useful!
thingiverse
Inspired by xilvar's "MP Select Mini Z Spacer" (https://www.thingiverse.com/thing:1808029), but tightened up a bit. One adapter fits 3 and 5 mm glass, the other fits 4 and 6 mm glass. ... Both are also a bit wider to keep them from sliding out of...
thingiverse
Remix to allow using mounts with the 4DM bed extension. You will need 300mm linear rails (instead of 200mm), no need for cutting. ...Fit is snug.
thingiverse
These replace the feet on the MPSM by utilizing the screws that are holding the bottom cover on.
thingiverse
https://www.youtube.com/watch?v=r0j-TXvVLSE Inspired by: Transport handle, by Ariehh https://www.thingiverse.com/thing:2353408 There is a list of alternatives: Monoprice Mini Select carrying handle: https://www.thingiverse.com/thing:2116139 MP Mini...
cults3d
Printed with 6x0,5mm walls, very strong with the notch full plastic.https://www.youtube.com/watch?v=r0j-TXvVLSE Inspired by: Transport handle, by Ariehh https://www.thingiverse.com/thing:2353408 There is a list of alternatives: Monoprice Mini Select...
thingiverse
After testing the THING from which I remixed, I found the size too big and the offset more than I wanted. While this remix doesn't get zero offset, it does move about 5 mm closer and gets the print head away from the front left plate adjustment...
thingiverse
Suporte para Monoprice Select Mini V1 e V2 para o carretel pequeno da 3Dlab. Desenhado no SketchUp, arquivo disponível. ... Usa um rolamento 608.
thingiverse
This is a new X carriage and mount for generic E3D upgrade on the Monoprice Select Mini V1. ... Nozzle body fan gets upgraded to 40mm There is a place to mount a small bit of euro barrier strip on top of the head(mount with M2 hardware) The...
thingiverse
So I found an ABS-Flag for the monoprice Select Mini V1 and found out that it wouln't fit the V2. I designed one for the V2. You just have to print it (Doesn't matter if ABS or PLA) and push it into the outlet of the fan. Make sure your clips are...
thingiverse
This is an improved (I think) fan shroud for the Monoprice Select Mini V1. It uses the stock fan and screws. The purpose of this design is to reduce internal vortices and hopefully allow better airflow over the nozzle to improve overhang printing.
thingiverse
Original design: https://www.myminifactory.com/object/replacement-z-axis-assembly-for-monoprice-select-mini-v1-52822 I used petg with 100% infill for structural integrity. Update 11/14/18: Added a second z carriage, listing as V2 specific,...
thingiverse
This is a replacement for the plastic X-Axis carriage assembly for the Monoprice Select Mini V1 and V2. This new carriage features a built-in E3Dv6 style hot end mount, and includes a stealthy GT2 belt tensioning system. You will need to upgrade the...
thingiverse
Fan Shroud for the monoprice select mini V1. It is very close to original design (not 1:1). I did not add the holes for the fan screws, you will have to drill them! ... Hop you will find it helpful.
thingiverse
Ein Kabelschutz für den Monoprice Select Mini. ...Passend zur Idee von https://www.thingiverse.com/make:747801
thingiverse
We lost one of the rubber pads on the bottom of our Monoprice, leaving an exposed screw head to scratch up our tabletop. This simple foot attaches with the current hardware, just remove the rubber pad and use the screw that's already there! ... ...