3d characters models

 V4 was still a solid design, but I made some very subtle changes based on my range outing last weekend where I was using it on a handgun.The Magnetospeed Sporter chronograph has some mounting limitations compared to the V3 model, so I wanted to...

Link below --- Build history Years ago, duno, I made the bigger first case desgin, roughly modeled after the original. 2021 -the 2.nd design of a modified, more streamlined versatile case was made. -modified the pcb layout -new pcb was made...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

I have left the original design files as well to preserve version control. Design File Included: .f3d, .ipt, step, .skp, and .obj files. Follow The Makers Workbench...

This is a procedure to prevent the bottom part of the model from collapsing. (a.k.a. elephant foot)  7. Nothing is attached to the top of the Z-axis frame yet. Do...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

First off, thank you ohman74 for posting this fantastic Buster Sword What a great model to work with!! I wanted to make the materia in the sword light up and be replaceable. After searching for LED balls on Amazon I came up with this perfect...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

The most common ones used for model rockets were very pricey and hard to find in bulk. I did some research online and found a couple of people having success with pencil graphite, so I started experimenting using an 18V drill battery as my power...

Select model on plate -> right click on it -> Add support enforcer -> Load..) Assembly Mounting the whole thing onto the printer is a bit fiddly. Here's how I went at it: <ol> <li>Remove the case from the hotend carriage and remove the old radial...

and all they could offer was to return the toolbox completely or bring in the suspect drawers and swap with floor models…This drove me nuts on an otherwise perfect toolbox and I had to fix it...The FixI designed new end-caps to enclose the aluminum...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... glad to finally get this published. Any questions about the historical nature of this set can be addressed to Simon at the email address above, and I will try to answer anything on modelling or future edits here in comments. ... -Ian R.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

I need thosethree measurements from that photo: Front standoff spacing, back standoff spacing, and front-to-back spacing.I've already helped several people from across the globe and I've been updating this document with the new models as I go.Post...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

2)The plastic for the case is about 0.5 kg (the lantern is large, it was made for a large candle) 3)2 hinges for caskets 15x21mm with self-tapping screws (included, sold on marketplaces) 4)a handle for the casket (you can print it, but I wanted...

Issues that I have with the design: In hand, the phone with my case (Model brand Apple silicone clone) on it fits snug. I can shake it vigorously upside-down and the phone doesn't fall out. However, After strapping it to the stem, the mount develops...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... some of the pictures may show older versions. All designs were made in (free) Tinkercad. You should be able to find each model there, if you want to tinker one. ...https://www.tinkercad.com/dashboard?type=tinkercad&collection=projects&id=dYW5jbPYAIP

Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...