3d mirror cube

I've included two pictures to show what can happen in your slicer if the settings aren't spot on. If you leave supports on for "everywhere", you will struggle to pull out the support that is put in built within the magnetic slot, so "Touching Build...

A rechargeable flashlight cap, to be used with 3dprintingworld's Collapsing Lightsaber (Removable Blade). The light automatically switches on when drawing the blade. Also needed: – Subminiature Microswitch (TS0101F020P) – YAGE Mini LED Flashlight...

There should be a small air gap between the 3D printed parts across the lock while locked. - Apply superglue through the small holes at the back of magnets and screws to secure them, but only after final assembly and alignment as explained above. ...

20211217I was searching around for a Google Chrome "Dino 404 error no internet" 3D model and never find one quite like I wanted, so I made one in SketchUp. The set include 4 cactus and 1...

Print instructionsCategory: 3D Printer Parts Summary This is a simple, micro-switch based bed level probe that costs less than $1 to make and gets the job done, reliably. Is is semi-automatic, in the sense that you attach it to the extruder or...

A short bridge is required for the rail end caps. Post-Printing All holes are intentionally modeled as very tight fits and are intended to be drilled out with a 3mm bit to ensure proper fit. The threaded inserts will push waste material into the...

Here is a photo of an early attempt of me replacing the ceramic by a part from a piezo buzzer :Achim has written very detailed instructions for the restoration of Tefifons, including how to replace the cartridge by a cheep Chinese one that is readily...

The middle cover took over four hours, but I used Archimedean Chords for Top/Bottom fill & 3D Honeycomb for fill pattern which I thought made it look nicer. I also included the openscad files of these, which give you the ability to change it a...

I figured that making precise parts is a perfect job for a 3D printer. My sled uses two pieces of 2-ft wide birch plywood, one for the base (length should be about the length of the table saw table) and an 8-9 inch one for the fence. The fence is...

Also, the final model was simplified to make "visible" for the Thingiverse 3D viewer.Referenceshttp://planck.cf.ac.uk/all-sky-imagesSurf to STL function for MATLAB Other astronomical objectsInner Solar SystemArtificialNear Earth AsteroidsMain...

(Don't confuse these with the incompatible Minolta autofocus lens mount, A, which began with the Maxxum line in 1985 and has been continued by Sony since 2006.) Because SR has a relatively short flange distance, there were not many adapters to mount...

The case is 3D printed to make the whole thing look nicely!Photos of the entire irrigation system with the required scripts are posted on my website - http://www.cEnz.at.The case is designed for the Raspberry Pi 1 - Model B (Rev. 2) but you can edit...

getting closer to being ready - just doing some testing...* One of my first projects after getting a 3D printer was to design and make an upgraded blower fan, as the one that came with my printer was a bit puny. I had already created a Better Blower...

You can use the right screw for plate alignment purposes but remove it as that hole is for the fan shroud screw. Marlin Settings Other than the usual auto bed leveling adjustments required in Marlin's "config.h" file, this is the offset settings for...

  Last, snap in...

I have a 3D printable spacer available as well, located at https://www.thingiverse.com/thing:5115001 Then, you will need 6 of the BT-5 (13mm) tubes of same length for the outside perimeter of the lower rocket section. When i made this rocket, I...

More information on the achievements of the association can be found on Windsurf EZ-TRIM Facebook channel : https://www.facebook.com/groups/378280849570793 More innovations are pending, so stay tuned our Facebook group and be daring with new ideas...

This print, because it uses all 3D printed parts for mechanical joins, must have tight tolerances. I would highly recommend at least printing two long links and a few pins and sockets to test expansion tolerances within the slicer.  That being said,...

A rechargeable flashlight cap, to be used with 3dprintingworld's Collapsing Sith Lightsaber (Removable Blade).The light automatically switches on when drawing the blade.To bring balance to the force I made this version for the Sith Lightsaber.Also...

After years of noticing wear and warp on my reusable Rocektbook notebooks, I decided to put my 3D printer to work to solve the issue…And voila - multi-material (TPU | PETG | TPU), customizable (colour, infill pattern + density) notebook covers that...

Print Settings Printer: Strongly modded Wanhao i3 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Infill: 50 Filament: any any (High Temp like PETG or ABS advised!) Notes: optimized for 0.8 Nozzle (just make sure that Walls are sliced...

(labeled ‘flat’ in folders)     type tldr → for 2 types of printing with/without support, minor differences advantages/disadvantages Versions (TYPE A/B):V1 (FULL) includes a little smiley cut out of the front clamp part and a little countersunk hole...

This self centring spool holder does not require any additional parts, components, or hardware other than the original bracketry which comes with the Creality Ender 3 range of 3D Printers and any other accessories you choose to use with it (i.e. a...

Make your own among us angel, with a luminous halo!Light up the dark with a mysterious impostor or crewmate.What do you need?3D printer :)White and coloured filamentSoldering iron, solder and 3x 18cm wireDigital RGB LED ring, 12 leds (OD: 52mm | ID:...

A 3D printed bell siphon that works from the start! Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: .5 ...

The buckle of my fanny pack shattered after plummeting from a third-floor window, giving me the perfect excuse to design something to 3D print. After scanning buckles on Thingiverse and reading comments sections, I set specific objectives for the...

One of my outlet ducts snapped to this should correct it. 3- Eliminated the small gap where the heat sink cooling fan was allowing air to hit the heat block. -I have lowered my standard fan to 50% ( was 70 in the notes above ) but maximum is still...

\r\n\r\nAs my new printer is built any changes I make to this design I will post to keep this design up to date.\r\n\r\nAlso I will appreciate any feedback from users who try this design so that I can further improve it.\r\n\r\nRevisions 2 added...

IMPORTANT!: I do not advise the installation of another or higher wattage light source, because of too much heat development!Light:LED Beleuchtungsstreifen, USB TV Hintergrundbeleuchtung 6.56Ft/2m LED Band, Nicht Wasserdicht SMD 3528 5V warmweiß Bias...