3d model exploded view

I'm in gun mode so I'm going to make some Gucci parts for my airsoft rifle.  The DanLARP Defense fixed front sights are modeled after the real thing, in true LARPy fashion. They are tool-less mount and are as snug as a bug. They feature a large and...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   A Wastewalker Ranger who was a renowned scout and hunter for the Boundless Wind Clan of Eastern Oldavor. Strika was said to have single-handedly slain a Nix Centipede, and...

Depending on the type of wall you are screwing into you might want to use wall anchors or screw directly into a stud.(Optional) drill pilot holes for screws using a diameter smaller than the screw.• If installing more than one battery holder please...

Meanwhile, using models created by Thingiverse users agmeadows, tgoacher, and slicerd can help complete your pack. ### PVC Pipe Caps These caps are intended for use with 1" ID PVC pipe, which can be used for the vacuum tube and two other tubes in...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on. <b>Donations</b> All my designs...

Supports required under the roof and body apertures.I tested this model all year outside and the birds love it.With PrusaSlicer, it is possible to reduce the capacity of the feeder by removing the same height at the top of the body and the middle...

... needed as well as the length of time needed for printing. If your bed's adhesion is spotty, feel free to print[hood_flat] instead. Print Settings Printer Brand: TEVO Printer: Tarantula Supports: Yes Resolution: 0.2mm Infill: 20% Category: Models

UPD4 I've added the front plate, modified from relwolf's model. It includes a cap and a clip piece to hold the cap in. I recommend you print the clip with a brim. Also, you get your ironsights back! I added an ironsight to the rear plate piece, so...

You can use any 3.7V lithium batteries as long as they fit the base model. Some 3.7V polymer lithium batteries have protection circuits, which limit output current, so they're not recommended unless you know how to remove or bypass them. 12 of M2x6...

http://www.thingiverse.com/apps/customizer/run?thing_id=195657 Instructions Using the following options: material_thickness = 3 outer_diameter = 20 inner_thread_pitch = .125mm length_of_bolt_threaded = 15mm width_between_thread_starts = -12...

... each box is a different body, and STL combines them. If you don't do this (or combine the bodies in fusion) you may get issues when you slice the model.Open the meshes in your slicer, slice, and print.Please leave a comment if you have questions.

This articulated figure was made using the actual in-game model of the creature (with the help of MPR and URDE), with brand new joints added to every articulation. Most of the pieces are just as they were in-game, with some modifications done here...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   Dwarves of Tharador are usually known to be resplendent lovers of nature, (despite the usual bad wrap they get as industrialists). However, there are many Dwarves who do fill...

I used a long stem (6 or 7mm) tactile switche I bought in as part of a set from Amazon. The code I used is here: https://gist.github.com/Arudinne/c540aa2470599e2cc87307d384696c95 A video of the patterns I used can be found here:...

Therefore I'm able to connect the geiger counter to my Home Assistant + I added a small OLED Display, to see all data directly when standing in front of it (+ 10 coolness).After the electronics where finished, I've designed an enclosure, based on the...

... setups. Hopefully this helps folks who were having trouble with them. If you feel inclined to support my work (and get access to previews of upcoming work and voting rights to future model options), you may do so here: https://www.patreon.com/nfeyma

After that, go to the model tab, and press the "download" button. Please note: the final dimensions of the Lithophane are 56(w)x75(h)mm, which includes a 1mm border around the entire lithophane. Repeat step 2 above until you have all your images...

Menos elementos menos posibles problemas.Gracias a todos.&nbsp;-------------------------------------------------------------------------------&nbsp;This is a remix of a remix, this time with inputs for G1/8" pneumatic connectors similar to the M10.I...

I used a 0.08mm layer height.Print nice and slow as this is a small model. Might want to <strong>bring down the speed</strong> or bump up the <strong>minimum layer time</strong>.</li><li>Perimeters: <strong>2-3</strong>.</li><li>Infill: I use...

If you like this remix, check out the original models listed in the left sidebar. I have designed almost 700 remixes of various types. If you want to search by the type, check this post as Thinigiverse has lost about half of my designs: ...

My model is fine enough so there's no need to print another yet. If it's too snug for you, and you have Fusion360, you can adjust the clearances on the Fx Parameters page.\r\n\r\nHUGE THANKS to Domestic Hacks for providing the starting point for this...

If printing on a Mini 2, just rotate the model 20 degrees (diagonal) and it will fit. Once printed, go to https://www.thingiverse.com/thing:1637988 and print the case and ball joint for the camera, and then you're all set! Note that I do recommend...

Premium version of this model with two kinds of brick patterns available on my Gumroads Store. Cheer up the gloom with some stone pillars/columns with real flickering torches for all your dungeon adventures. No soldering necessary!</p> <p>The base of...

I'm working on modeling a 100mm extension that will go in the middle so you can go up to a 350mm card, but haven't worked on making it taller or wider.   Real Info: I didn't like how large all the other chassis available on the market, so I decided...

To fit my print bed, I used six 60-degree wings for the large 406mm OD model; it might have worked with three 120-degree wings if the internal diameter was larger. You can select from 30, 60, 90, or 120-degree wings, although 90 may not be ideal for...

This company specializes in LED light kits that can be used to enhance Lego model sets, but they also sell individual lights in their DIY section for custom projects. (They have a store on <a...

No glue was needed on the model.Ideas:Room name tag displays: Using bigger ePaper displays with this solution could become an easy naming system for rooms in an office, where you can change the names more easy without to cut out paper labels again...

Make sure to select all the files/models when moving/rotating so they don't get out of alignment. I sliced with .25mm layer heights. The inset is .5mm deep, and the depth of the grooves between the squares is 1mm. That gives a total of four layers...

The hole in the tip should accommodate most similar cables, but if not, you can easily remix the model by enlarging the hole or adding material as needed. I recommend printing the dock upside down and including support material that touches the bed...

DISCLAIMER: Now, by supplying the model of this tool, it doesn't mean you're a qualified repair person. I wouldn't do this on my in-laws washing machine, so don't complain to me if things go badly. Get a professional in if you have doubts. I have a...