3d print filament storage

... PS: If the LiPo buzzer is too loud, stick two pieces of bubble gum into the holes of the little speakers. This will muffle the sound and still make it loud enough for you to hear it. Enjoy printing and building! ...Have fun, don't forget to like!

Recommended Material for printing: Sainsmart TPU @ 01.mm / 210°C/ 40mm/s / no retraction Update: You can now buy my Gatehunter pod combined with the LeDrone Club Pickle frame from...

Comes in 32mm and 75mm Scale - PreSupported option available (Actual printed size is 65mm and 150mm respectively).   An elite fighting duo that are legendary amongst the front line and special operatives of The Golden Griffins. Just the sight of...

I have included two versions of the mount, one is with the rail centered on the overall enclosure and the other is with the rail centered on the top part of the enclosure resulting in a slight (5mm) offset from center. I also went ahead and added in...

I printed about 5 of the sleeves to get the lettering just right and included the gcode so you can get the best quality settings without trial and error. Included are 2 different back covers: one solid and one cut for a 40mm fan (shown in red setup...

After checking the accuracy of fit with a test frame, I was able to print the complete funnel and fit it with two filters and mount it on the suction cup without any further adjustments. ...After the first test, the suction power is not hindered, the...

You can get away with with printing them bigger, especially 2 4 6 and 7. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a href="https://www.patreon.com/bePatron?u=30583762"...

I will need a spacer, either printed or metal, between the pulley wheel and the top bearing of this mount block. I have to figure out what height of spacer will put the pulley wheel at the same height as the pulley on the stepper motor using KIdz's...

Most of the clock face parts will be identical to those in the Quartz Upgrade, with this design featuring a variation of the clock face (Clock Face w Embedded Numerals) that can be printed in 2 colors where the second color determines the color of...

Important Update - 22-08-2016 Please refrain from printing this design version as it has been found to contain incorrect belt paths, not set up perpendicularly. Check out the discussion on RepRap forum at:...

The 10 x 10 x 10 printer has been used for printing and assembling the entire device so it fits inside a standard record label, leaving minimal space for intricate animations due to its size. A key feature of this ZOETROPE model is its ability to...

Here are the required parts: * 5x M3 22mm screws * 1x M3 20mm screw * 6x M3x4mm Brass Knurl Nuts * 1x M3 plain washer * 1x tiewrap 2.5mm 100mm * 2 x LM8LUU (45mmx15mmx8mm) * 2 extra pieces of thin layers for testing the x_stop switch, which can be...

UPDATE: I have reworked the top and bottom of the case, enabling it to be printed without supports being turned on. I have also relocated the USB and Ethernet port partitions to the top half of the case to ensure their stability when installing the...

... which could scratch your film. Expect to update the design to allow for constant agitation, eg. rollers. PS : Needs to be printed in the vertical direction! Comments most welcomed! ...send your thoughts and experience morten@kolve.org

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

Because there are no symbols in the other three statues it is difficult to identify them, and their names are indeed a vexata quaestio; according to Raffaello Borghini (1584), what they were actually called depended entirely on the oral tradition...

... list, the Max Travel of Z is 250mm. You can achieve 260mm but homing with the raise before descending will catch the fame corner on the X motor. Print Settings: Printer: Wilson II Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 80%

It is printed as seen on the screenshots, supports activated (only necessary below the red areas) and preferably with a Brim. The printer should be calibrated, the place for the fan is 80.2x80.2mm and for the filters 81.5x81.5mm. So everything...

I printed the body and other parts, mounted the sensor in the sensor mount then glued the parts in place. As for the missing parts, get these from the original design that I remixed this from. ... Link to downloads for motioneyeos:...

You only need to print two sets of screws. One for the north celestial leg and one for another leg. The screws have 80mm length and can level at ~50° incline, so a distance of ~40mm. In the middle of the inner screw is a marker that shows the...

Bill of Materials (To build the extractor fan as pictured) Printed Parts: 2x Fume Extractor half 1x Extractor Switch Housing 1x Extractor Arm Mount 2x Tooth Lock Arm 1x Tooth Lock Arm Short 3x Finger Grip Bolt 3x Finger Grip Nut 1x Base Finger Grip...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver - ...

... convenience. Feel free to modify them however you please and post remixes for the community to benefit from! Print Settings: * Printer: Flash Forge Creator Pro * Rafts: No * Supports: Yes * Resolution: 0.200 microns for most parts * Infill: 40%

The Stem-mount parametric model didn't produce flat sides with larger stem sizes which made it hard to print. I've updated the .f3d file so it forces flat sides. I've included two properly parameterized Fusion360 f3d models so anyone can now create...

It's also very easy to print with. Use the photos for reference of my assembly description. Motor mounting Cut a piece of thin double adhesive tape about 5x5mm in size. Stick the tape to the inside of the motor holder on the frame. (See picture) ...

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

Designing and drawing this model required over 1200 hours of work, and printing it took an estimated 2000 hours. The model uses various colors in PLA, including True Red (10 pounds), True Yellow (2 pounds), True White (8 pounds), True Black (4...

I have design it in order to be printed in a 200x200 mm printer (the most common). Everything is my own design exept the front lights which I have to thank to my friend Cooperino who make a fantastic desing work =D. I've tested the model and,...

The zip files contain the STL files for the parts to be printed, but also the complete 14-page manual on the technical configuration of the robot. ... Videos available: Operation: https://m.youtube.com/watch?v=ApX3t5t67Fg&t=22s Assembly: ...

... for the electronic you can use pro micro, smt32, or leobodnar bbi board FOR PERSONAL USE, YOU CAN'T RESELL THE DESIGN, THE FILES NOR THE FISICAL PRINTED DESIGN, YOU CAN'T NEITHER SELL ANY MODIFICATION OR DERIVATIVE OF THE ORIGINAL MODEL