3d print monitor shelf

Keep a look out for this.Designed for the Ender3v2 but more than likely fits other variants, however an OEM Creality controller board may not work unless it has a spare driver port.BOM2 printed parts in PLA.Bondtech Pancake stepper with spur gear...

This design is the result of a lot of trail and error and a lot of test prints to fine tune the placement of the straps, but I'm very pleased with the results. One caveat, these were custom designed for my hands, so your mileage may vary...

Leave me a comment if anything needs to be modified I preferred to make this support in 2 pieces to be glued with 2 centering studs to avoid removing the tedious supports after printing - March 11, 2022: Added removable "capuchon amovible V2" which...

Its software is very well documented, I had no trouble adapting it to the realization of a printed circuit.(K40_Bed_Software.7z and K40_Electrical_Board)...

I'd recommend the hard edges badge as it's more complete and comes out cleaner!Post-PrintingWhen designing this badge, I wanted to replicate the exact measurements of the real deal badges from the show. So, you need to account for some sanding in the...

In order to shrink the parts to the printing platform, I split them into pieces. The diffuser is required 4 times. The GU10 parts and the corpus parts are required 3 times. After putting them together, I glued the parts together with acrylic glass...

...The benefits are lighter weight on the carriage and can print high temps/high temp enclosure without worrying about fans. With a Sharpie mark two lines across the fins opposite each other on the heatbreak, completely blacken the top and bottom fin.

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI Updated the led cover to cover the whole top. print four of them then glue in place. A kinetic sand...

Premier essai sous Fusion 360 d'un modèle paramétrique, car j'avais besoin d'un bouchon verseur pour un petit flacon. Sous Fusion pour accéder aux paramètres : Dans l'espace DESIGN > MODIFY > fx change parameters Vous accédez alors à un...

My recommended print settings include 4-5 outer perimeters and shells on all sides, as well as 15-25% infill. Filament was PLA. Special thanks to the zerspanungsbude.net community, a German-speaking forum that provided valuable assistance during...

I have no idea how common that is, so I'm including my printing files, but also the .svg files and .png files I used to make them in the component parts folder. Hopefully they'll be a good starting point if you need to change something!Coin door...

Versions Single Point Variant 1.2 (25 Mar 2022) - Added options for rear screw (Screw_Direction and Screw_Hole_Depth) 1.1 (1 Dec 2020) - Improvements for Thingiverse Customizer 1.0 (4 Nov 2020) - Initial version Dual Point Variant 1.2 (25 Mar 2022)...

WE don' need no stinking WIRES!!!" As with my other implementations, B-25 Mitchell https://www.thingiverse.com/thing:4121096 Spitfire Mk IX https://www.thingiverse.com/thing:4143803 F4U Corsair https://www.thingiverse.com/thing:4178322 Il-2 Sturmovik...

Ideally a clamp with a spring for easy remove. Circuit schematics are available here thanks to Jeff Frohwein's work : http://www.devrs.com/gb/files/hardware.html http://www.devrs.com/gb/files/mbc1.gif http://www.devrs.com/gb/files/134a.gif Print...

Refit the metal plate to the carriage slider and tension the belt, then slip the newly printed inner Gantry Support plate into the unit above the filament feed motor. Line up its holes with the holes you have drilled, then reconnect fan cables and...

Now here's the problem I've found: after cleaning two beds, the glass is warped in the upper direction when turned over - the hold-down clips pulled the ends down and leveled the glass, so some creative leveling will be needed to get printing again....

The component that is printed correctly with increasing exposure time is then the correct exposure time. If necessary, watch the video again to avoid making a mistake in the order. E.g. ...part (4) looks good: 1 second for part(1) 1.25 seconds for...

I want to keep the same ideas of choosing coins blindly and guessing their character based on how they feel, but I also want to add the challenge of creating words with Zhuyin and using those words in a point system of sorts - this may require...

So, after some research and test prints I have finished this. Which I am currently installing on my Creality Cr10-V2. This is a derivative of a derivative and completely redesigned and fixed using their work as a template. I'll list what I changed...

Since Creality systematically refuses to supply Sermoon D1 customers with spare parts of parts subjected to natural wear, such as Hot End and simli, having some problems with the original, I decided to re-build them, improving them to obtain a...

Dos opciones: Left - PAra colocar el seguro del mailon a la izquierda Right - Para colocar el seguro del mailon a la derecha El diseño original tuvo 2 versiones La version 1.0 tenia esquinas y un error de 2 grados En la version 1.1 se corrigio el...

Supports: Yes (if using Cura we recommend using the Tree supports option and adding a 'Brim' to help the Tree supports adhere to your print bed) Rafts: Doesn't matter Links View on Cults View on Thingiverse License The "Personalised Voronoi Sphere...

**PRINT FILES** * `VPC_Desk_Mount_Rail_Adapter-Stick_full_assembly.obj` is one fully assembled example mount for one flight stick. This is just one example how the parts fit together. **Do not print this.** I am not sure if all contained objects are...

... onboard leds. Printing in black PLA should be enough to block all the light. I know the color scheme *is not exactly wonderful* for something that is going on stage, so I think I will spray paint it soon and print the buttons again in black TPU.

The 4 printed circuit boards with LM358 are required to be able to integrate the measuring device into the positive supply line, since the measuring devices can only be integrated into the negative line of a load without the additional circuitry,...

All accessory mounts needed to be printed with support and the flat top down except the laser aimer that needs to be laid on its face aligner pointing towards the sky. The laser holder/bltouch mount also needs to be printed with support Laser:...

** You can purchase this case printed from my store by clicking HERE **This is a case for a RAKwireless RAK 5005-O WisBlock base board, designed with the Meshtastic project (https://meshtastic.org) in mind. ...It will accommodate the RAK5005-O base...

:) Suggestion : print the knobs with a different color from the extruder itself, it'll be more fun. ;) VERY IMPORTANT! You must set the following variables in the Configuration.h of your Marlin firmware and recompile/upload it, otherwise your new...

If they do that, one can imagine what are their revenue strategies - instead of making 10 EUR less margin and giving clearly more robust bicycle. I am furious. Therefore I decided to print a repair part for less than 1 Euros that i can replace myself...

Non tutti i pin sono utilizzati dai display, basta mettere solo quelli che gli servono. Essendo il display distaccato dal Raspy, si potranno collegare i fili della seriale, provenienti dalla Einsy della stampante, in modo ordinato, mettendo dei...