3d print playing card holder

(incl 5 parts for standing on the Bulwark riot vehicle) - Police Riot Dogs x 3 poses - Detective Welles of The Watch Police - Brigette Holt - robot engineer, NPC pose - Brigette Holt - robot engineer, mech version in a fighting pose - Alex Alvarez,...

Thicker panels and prints good now in 1/25th scale *UPDATE: 10/09/21* Uploaded a revised truck bed, this time with wall supports, Rev B *UPDATE: 10/06/21* Revised the truck bed, made the walls a little thicker and smoother, Rev A for both Pro Street...

Left to our own devices to scour the net for solutions, (clearly we weren't the first people with CR10S Pro V2's to have purchased this product...right?!?) well after printing three different models that just didn't fit my setup quite right, I got...

https://kc9on.com/product/fox-hunt-offset-attenuator/ ###What is what### To use this case, you'll need to print the cover and one of the cases depending on your choice of connector. FoxhuntV5C.stl has no antenna outlet for you to modify it to your...

If they break reprint your model and try again or just glue it in place Reassemble you should be good at this point (unless you didn't test it along the way) Post-Printing This is my video on how to assemble the kit and the mod, it's also a video...

-Customizable pipe cap https://www.thingiverse.com/thing:4795549 ...this thing -Customizable Pipe Cap "Cover type" https://www.thingiverse.com/thing:5150957 -Customizable Rectangle Pipe Cap https://www.thingiverse.com/thing:4875215 -Customizable...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following settings: nut_step_angle_radians = 0.7854, thicken_value = 2, hex_head_style = hex, bolt_size_in_mm = 5, screw_length_mm = 25,...

 The only repair is replacement of the hammer, as epoxies and glues will not hold.I printed this using Prusament PC Blend, as this hammer needs to withstand some serious punishment to actuate the gas valves without breaking.  The PC blend...

Endstops The Y-Axis endstop is a single mount for both front and back switches, activated by two tabs mounted under the bed with M3 screws, nuts, and printed M3 T-nut converters. The upper Z-Axis switch is clamped to the Z-Stepper motor RHS...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. …...

Every glance at this work of art will make your eyes light up with admiration.Printed in PLA or PETG, the robust material ensures long-lasting stability, giving your board a firm hold while creating a harmonious connection between window and...

You can get away with with printing them bigger, especially 2 4 6 and 7. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a href="https://www.patreon.com/bePatron?u=30583762"...

Included files:   This bundle includes HEXTECH Universal features and Magnet Connections, allowing for prints to be used easily in either hexed or hexless formats. ...  Files Included: Curtain Walls Straight Section (Hexed and Universal Format)...

Just remember to test print a small pocket first to ensure it fits within the button's dimensions (the pockets in the DXF are 0.1mm larger than the buttons). Given the variability in printer results, I've added multiple buttons with different upper...

I place the magnet on the frame of my bench and press the printed part over the magnet. All sizes are parameters in Fusion360 and easily altered to fit various tape size or to change the overall size of the unit. I have included all the sizes I...

Sliced with PrusaSlicer, this design tests your printer's ability to print thin words without any layers on any side, showcasing its "floating" capability. Dimensions of the design: The base plate is 16 millimeters by 51 millimeters by one...

Print all parts as already oriented with no supports. You will need 2x 'Tronxy X5s belt aligner wheel'. You will need; 2x M3x6mm bolts (for bottom mounting) 2x M4x30 bolts (for belt aligner mounting) 2x M4 nuts (preferably nyloc) (for belt aligner...

Files with FDM are modified to print better with filament printers Set 04 - Generals and Staff - FM Bluecher in several poses, plus a few generals and other staff officers Set 05 - Misc. Officers - Many Reserve and Landwehr officers wore regulation...

Most models have built-in fan speed controllers which switch off the fan at idle and vary the fan speed according to the PSU load. Compared to the original cover design by sneaks, I've changed the following:thickened upper PSU mounting area to...

You'll need to print out robertguy's rear case, and I expect you to show your appreciation for his project by giving it a like when you download it. Don't forget to visit flash24's design and give it a thumbs up too! I plan to add a step-up module...

... shape con the center of the top side). I have only checked the grids with TT685 since I do not have the others. I would be very grateful if you could publish your photos made with this grids. Do not share the model files nor sell printed grids.

base not included very high quality details i will update the files if you have special requests thank you so much for reviewing and commenting file updated 28th Dec 20 smaller cutted parts for easier print Spinosaurus (meaning "spine lizard") is a...

To prepare for printing in STL format, I plane-cut the bottom of the model to make it level. I exported Moses in various formats, hoping that the texture map would be copied intact. So far, only the DAE file achieved this; the PLY and OBJ files...

This mod requires a new XY end-stop bracket that houses both end stop switches (I suggest printing it in >50% infill TPU so it has a bit more flexibility to insert the switches, but is still rigid enough - not loose, not crazy tight) , and a few...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...

Geoff Gregor's notes on his R2a modification state: "Summary: Nut pocket slightly bigger, screw head pocket much smaller, less damage, no more slop, screw stays aligned for happy printing (hopefully)." After struggling with a squeaking belt on my...

#Installation instruction: ##Hardware: Print, sand, use some hot glue to attach the screen to the shell and to glue them together. ##Software: Requirements: none for standalone version www + php server - in my case Lighttpd + PHP on Raspberry Pi 3+...

A new thicker-walled Ramps-FD box has also been created to help those who have trouble printing the original one. This is version 1 of my Ramps-FD enclosure, featuring a 30mm fan and an EEPROM hanger. I am upgrading my Duplicator i3 with Ramps-FD...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Agannon,...