3d printed action figure

with open("input_data.txt", "r") as f: for i, line in enumerate(f): if line.strip().endswith(":"): variable_name = line[:-1].strip() value = f.readline().strip() if variable_name == 'pattern_element_radius': exec(variable_name + " = float(" +...

Models include the popular cable chains by johnnniewhiskey over on Thingiverse, a PSU mount for the Ender 3 Pro by Cancerix on Thingiverse, amazing riser feet by thrutheframe over on Thingiverse and also some inspiration by zoly15 here on...

You'll need to print two of these, but don't worry about mirroring since this is symmetrical and so is the gap it fits into. You will need to upscale this object by 12.7 times or with an X, Y, Z of 101.6mm x 31.74mm x 10.38mm. With this scaling,...

It doesn't cost you anything extra, but helps me out a lot :) Print instructionsCategory: Decor Summary This is a laser cut cube with a dolphin pattern on the front face. Behind this pattern is a frosted piece of acrylic, which gives a very nice glow...

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

The new firmware includes aggressive temperature management to reduce overheating, thus minimizing print failures due to excessive temperature levels. Settings for fans and Z-axis probes: My updated 3-point triangular probing is now default with...

My version is intended for those who want to update their stock motherboard with a drop-in replacement such as the SKR Mini E3 or the Fysetc Cheetah so they won't need to print a new right case a second time. Instead of using TLSmoothers, I added...

Plug in to your pi, then expand your file system using "sudo raspi-config" There are a few ways to access your print server. Find out your RPi ip address, then type it on your browser http://printrbot.local/ My image has avahi installed, which...

Changes I made to existing models: * Removed cable tie bump things because they're unnecessary and just add to print time. * Added holes on the Raspberry Pi panel so you can zip-tie extra Z cables in a service loop. * Changed the PSU front panel to...

- Some nice, yellow PLA (I couldn't find an exact color match, but I got close!) - Revel Contacta glue - A hot glue gun - Some clamps - A soldering iron (with a small tip) & solder - A small, flat-head screwdriver - [Male & female USB C...

for placing the drill holes or cable duct to where you need them) feel free to do so: https://www.tinkercad.com/things/fl1c7XRRpbD Post-Printing ========== Preparing the USB-C cable ---------------------------------- I removed the casing with the...

I use this as a wireless monitor for framing a shot. But there are some killer features of a DSLR I wanted to have on my phone when filming. So I made this Camera Rig and I slip my iPhone into on days I'm filming.  Print...

The launcher handle and rack parts should be printed in PLA (it's stiffer than other filaments) and with at least 3 perimeters and at least 20% infill. None of the parts need supports.LaunchingFirst, roll the wing onto the rack of the U-shaped...

I suggest printing the top pieces in something more heat resistant than just PLA, preferably carbon fiber nylon or polycarbonate. ASA should work pretty well too. For the bottom pieces, I used PETG as it allowed for the cards to slide in and out...

Instructions : * Before to print case, you can specify how many sensors you have. * You can define the exact number of sensors, or plan more. Each socket will be pre-cut for future use. * Follow joined scheme for assembly. * Each sensor have to...

This driver has no Enable pins so the code takes care of this when controlling the speed)2 dc motors (I used some refurbished N20)TP4056 to recharge the batteries2x 18650 batteries connected in parallelvarious screws and wires - usually what you have...

I also made some minor tweaks to make the counters look better for 2 color printing. Use layer height of 0.2mm and set your second color to start at the 14th layer. Update 4/22/2019 -- Treasure, Brick, Exert, and Embalm tokens released! Treasure...

Print the board and 16 pieces. Cults will not allow me to upload the rules document so I will paste bellow. Object of the Game Be the first player to move all four of your colored pegs around the game board and into your FINISH line. During the...

Hopefully someone will find it useful (Other peoples prints always look better than mine anyhow!) Sources: Wrapped Egg - Single Extruder by bugman_140https://www.thingiverse.com/thing:2806597Body from Yeti by...

POST-PRINTING There's room to mount a Micro-USB breakout board (see pictures) if you'd like to supply power on the side rather than out the back. These boards can be found here: https://www.amazon.com/gp/product/B0183KF7TM The BoB is mounted to the...

It is very easy to assemble and if you print an array of this devices you can have a grid for domestic use or outdoors activity like in a camping etc. This wind turbine device is a part of a further open turbo-machine system based in a pending...

At one point I printed my own little nylon washers, but when I found what I wanted in the bigger hardware store not so close to home, I jumped at that upgrade! It turns out that there is just the right amount of resistance so that I don't expect...

... using it myself. No guarantees, that this solution works. If you print it, please give Feedback to me and the community (by commenting or posting a make) if the brush works. ... ----------------------------- ATTENTION -----------------------------

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

base not included very high quality details i will update the files if you have special requests thank you so much for reviewing and commenting file updated 28th Dec 20 smaller cutted parts for easier print Spinosaurus (meaning "spine lizard") is a...

This format resembles a CSV-like list but seems to represent more structured data about design patterns and stencils for making printed circuit board (PCB) templates. The structure of the settings can be grouped as follows: ### Geometry and Stencil...

http://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following options: image_rotation = 30 degrees to enhance viewing pleasure pattern_shape = a geometric design choice with six sides to create complexity 5cornerR = 8...

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

Details and links in the description below. Print instructionsI  used Fusion 360 for this project. Thank you Autodesk for letting me  play with your amazing tool! </p> <p><strong>NOTE</strong> The Fusion 360 file attached as a ".f3d" file but the...

My huge thanks to both of them. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2**Rafts:** Yes Supports: Yes**Resolution:** 0.2 mm Infill: 20% **Filament:** [ Makerbot PLA...