3d printed flamethrower

Print quality is good, and I'll try a benchy and ghosting test later. The diameter of the sticks is 7.2 mm, but sticks with a diameter of 11 mm can also be used - they're almost three times as stiff in theory. 7 mm glue-sticks are fairly cheap, and...

I have added an additional complexity to the movement because not only do the gears spin, but the axes of the gears rotate too. Being a kinetic sculpture, you really need to see it in motion: http://www.youtube.com/watch?v=Zx28cHA4\_KI Be warned that...

... amélioré : plus esthétique (et d’autres éditions spéciales;) ), système d’éclairage led, etc. Pour suivre ces améliorations, n’hésiter pas à vous abonner a ma page Thingiverse et Facebook : https://www.facebook.com/waikikiprod Bon print à tous !

**What you need:** * Printed mount (not required, but I don't like loose stuff in my control box) * 1 Mosfet Driver * 2x M4x6 to mount holder to power supply * 2x M3x6 to mount Mosfet Driver to mount * Wires to connect power output to Mosfet Driver...

To print: Ender 5 Normal: ---------------------- Ender 5 and 5 Plus RAILMOD - Tensioner Side v2.0.stl Ender 5 and 5 Plus RAILMOD - Motor Side v2.0.stl Ender 5 RAISED RAILMOD - Bearing Bracket v2.0.stl Ender 5 RAISED RAILMOD - Carriage v2.0.stl Ender...

The zip file contains a more complex version which includes: A working Draw, A sliding panel (printed in situ, it is easiest to free it using a screwdriver blade). The dials on the panel can be rotated and using translucent filament the bank of...

 If you're adding a rackmount device, you'll need longer screws for the ones that go through the rack ears.Smear a very thin layer of urethane glue on the faces of the corner brace, position it, and drive in the wood screws to hold everything...

Make your sky watcher goto + track for around $200A hybrid of many of the onstep projects but without having to cut a larger hole in the base of the sky-watcher.Parts needed:onstep board: in my case a fsyetc e4 - preprogrammed...

The 18 to 22 pipe fitting could be removed This plate could then be copper plated with this technics : https://www.thingiverse.com/thing:1661301 If you have any design to share I would be glad to offer at least the binary codes of the ESP32 and the...

... is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)... Print Settings Supports: Yes Category: Outdoor & Garden

Note: I actually haven't printed any of these. I'm a designer for Shapeways here: https://www.shapeways.com/designer/jonathanmarch/hire-me. How I Designed This The Work First, I found a font that I could use for anything that also connected most...

I will post it in the files once I have printed and tested to make sure it meets my expectations! The following adjustments are being made: Larger base plate, more compact index to provide more angles, shortening the arms to not go beyond the base...

The printed version doesn't grip the shaft on which the thumbstick was mounted as well as the original part and may slide a little over time. If you follow this design exactly then you have 2-3mm to spare. ## Installation instruction (crude) ...

If you want to print dual color and are on version 4.7 or above, please either modify your gcode after you generate it or download a plug-in from the marketplace called Printer Settings. Then enable and check Extruders Share Heater and Extruders...

just in case the original author decides to take it down for some reason.) https://www.thingiverse.com/thing:3579224 The first 7 pieces replace parts in the original, so obviously dont print the originals of those. 8-11 are in addition to everything...

Failure to do this will likely result in decreased print quality. I tried several Z wobble upgrades but few fit right and the ones that are close don't secure the lead screw. I designed this based off of my Tronxy P802MA printer and I can guarantee...

*** Do not print this in PLA as it will melt or sag inside the car *** *** You must provide a charger *** This design is tailored for a 2019 Highlander, but it should also fit 2017-2019 models; I am uncertain about compatibility with other years. I...

eerything you need to play is included, it's an easy print for a game that you will play for days and days!!! hope you enjoy it!! Rules: in french sorry... (you can copy and translate!) Material list - 1 game box/stand - 1 game board - 4...

You can do finer adjustments to the tolerance by putting some scotch tape or masking tape on the inside of the shell wall. Print the shells with the flat bottom on the build plate at 0.3mm layer height. You might want to add a 2 or 3 mm brim to...

In the meantime I have developed this holder for 30x 1 Euro pieces so that you can just put the whole thing in the glove compartment and the coins do not roll wildly through the area.The distance of the coins is minimal from each other and the...

WhatA modular corner and side holder/guide system that allow the CNC to cut dovetail tracks for the matchfit system into the spoilboard and slide in clamps by removing the walls but leaving the holders screwed to the table.It uses a modular system...

Additionally it was printed just out of PLA. you might get even bigger strenght with more perimeters or other materials WARNING:This hook is designed with mooring and releasing some light wight gear in mind. DO NOT use it for climbing or in cases...

The dustshoe has a total of 5 parts that easily can be printed in three parts or maybe even less. It contains: A base part called Dustshoe basis (with the version on the end) Then a part to attach to your vacuum cleaner called Dustshoe...

There should be pre-made holes to support an M3/M4-Screw, to hold the panels in place.The desk plate fixture arm had no print support. Support should be generated where necessary.</li><li>The fixture arm doesn't fully recede into the hole, which may...

Key features: - low profile with 22mm (depending on T2 extender used) - integrated stray light guard - camera rotation possible - thermal isolation from camera to filter (especially handy with heated Etalon filters) - tested with a 500g camera...

Manifolds pictured were printed using nylon 6,6 weed-whacker line because that's what I had on hand that could handle heat and chemical exposure. I believe ABS/ASA would actually be a superior option, as you could use acetone to seal and fix the...

... Button pack, for those that like the style better. These ONLY work with the Build A version, using the 1.3inch LCD The "Shims" files are thin shims you can print and wedge between your Pi and the case layers if you wish to add rigidity to the case.

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

I'll update this when my print finishes. The Fly can fly from any position to land on any bug that that your opponent placed, moved or flipped on their last turn. This includes bugs on top of a stack. It then moves one space down into an empty...

* **Slides: sacrifice layer for successful prints** The track slides are designed with a 1-layer-thick sacrifice layer covering where the bolt hole transitions from hex-head area to round-shaft area. You can burn that thin layer out with a soldering...