3d printed gpu support

The front shroud includes a slider that allows the air flow to be redirected away from the printed part if required. The Triple Lower Vent attaches from the bottom using 3-M3 countersunk machine screws. Because the vent adds some height, the...

The sensor is quite near the nozzle, but I've noticed no problems so far printing PLA at 220-230°C. You may need some spacers to reach the right probe distance in the z-axis. Carefully check if the sensor reacts before the nozzle hits the bed. The...

This file contains two layers that must be enabled and printed on separate sheets of transparency, each with a slightly different scale. One sheet requires folding along its long dimension to fit into the angled groove of the side pieces. I...

##You will need: - two MGN12 linear rails 400 mm long with MGN12H blocks - about 16 M4 hammerhead T-nuts (quantity depends on the required rigidity) - the same amount of M4x12mm flat head countersunk screws - about 16 M3x8mm socket head cap screws...

... as an individual piece: top, bottom, button. Make sure to leave the translate and rotate function commented when compiling for export so that each piece is flat side down. I printed mine at 0.15mm layer height and 25% infill and it worked nicely.

I have a modified version ready for printing, or you can simply cut out the piece that's in the way and make a new one. That's how I did it. V2: But if you want to order a new display and do some modifications, you can also just swap the original...

I was constrained by the size of the rotary switch and the USB breakout board otherwise it might have gotten a bit smaller. See it in action: https://youtu.be/PTTVuVUZYM8 I have included the OpenSCAD file which is somewhat parametric. Print...

This is printed and tested and works, though I prefer the regular rollers in this design. (UPDATE - posted here: https://www.thingiverse.com/thing:4979880) * I also designed a mount for a 2020 rail, such as the top cross rail on an Ender3,...

... Some part coolers like the "Petsfang" & "Bullseye" seem to crash into the camera housing during autobed leveling. Many thanks to "acwest" for pointing out that problem and his solution! ===================================== Have fun printing!

These are the various frame fittings to go along with the replacement X carriage parts for the toolchange system, here: https://www.thingiverse.com/thing:5149609 Note that this is not a stand-alone toolchange system - these two sets of parts are...

With S3D I can change my temperatures when I print from the machine control window, so I can use different filament using the same gcode. The base mounts the vertical coin holder base. The CR2032 holder is common. The fit is not real tight and you...

... a piece on the bottom to prevent the gap on that side. Hopefully it won't interfere with putting the cable in too much. Update: I goofed on the previous one, and forgot to include a hole for the power cable, so now I'll have to print a third time.

Deprecated: Please use newer V2. This is my attempt to design a mount for the Bondtech LGX extruder with the LGX FF for flexibles hotend kit. The extruder is mounted sideways attached to a mounting plate via two M3 side screws into the extruder...

**Example Python Code Using These Parameters:** ```python import math # Sample Function: def generate_branch(shape_id, current_x=0.0): print(f"Generated branch at X: {current_x} ShapeID={shape_id}") class BranchTreeGenerator: def __init__(self,...

ELECTRONICS BBI-32 Button Box Interface - No Connectors (1) http://www.leobodnar.com/shop/index.php?main_page=product_info&cPath=94&products_id=206 Micro USB Hub (1) https://www.yoctopuce.com/EN/products/extensions-and-networking/micro-usb-hub-v2...

If you decide to set it up just like me, you'll only print the front case STL. But if you'd like to set the LCD in the bottom position, you'll need the back STL too. UPDATE 2: Added a 40mm silent fan, enabled only when drivers are enabled and last...

I think the rear is further apart, but you'll figure it out quickly when you try to attach to base.Use M6x35mm screws and M6 washer to attach top-cross bar assembly to the base! Other Remarks:Printed with Carbon Fiber PETG.Infill at 40%Used with...

I switched materials and I am now convinced that the print quality is actually quite a bit better over the original gantry. Update 2020-04-04: Made a v4. Changes from v3: * Added cable management rings to all the mounts * Added BLTouch versions of...

Features: 1 - API 2 - powerful chassis 3 - Bluetooth for control via API 4 - open hardware 5 - uses the popular Arduino shields To build this robot you need: 1 - to buy a DAGU Rover 5 (https://www.pololu.com/product/1551) 2 - to print case:...

Instructions 1 - Print both halfs 2 - Insert desired weight in lead into the pockets. weight in the back will make the lure running shallower, weight in the front will let it run deeper 3 - cut a toothpick and use 2 sections where it doesnt taper...

Features Include: 4 Rails Retractable stock Improved Clamping System Very Lightweight 10mm Higher than my previous designs 15mm Wider than my previous designs Ambidextrous Charging Handle Accept a compensator or suppressor Requires a 200mm print bed...

He spent his early years at the Hermitage Museum as curator of prints and superintendent of the museum's Imperial Academy of Arts division. Utkin's mother was a serf on Mikhail Nikitich Muravyov's estate, who is believed to be Utkin's biological...

I also added a small electrolytic capacitor to stabilize the power to the ESP32 to prevent low power brownouts, 47uf / 50vdc - More than a than...

Now fit the 80 tooth pulley printed part and secure with M5 screws and nuts. Check how long the rod needs to be by fitting the orange metal part that attaches the weights. Measure the gap between this part and the pulley. Remove the metal part and...

You'll need to print out robertguy's rear case, and I expect you to show your appreciation for his project by giving it a like when you download it. Don't forget to visit flash24's design and give it a thumbs up too! I plan to add a step-up module...

Notes: Parts to print: 2x middle, 2x center, 2x center (contains mega x) 4x side, 4x corner Start mounting the middle parts using the original short screws. Once they are fitted you can easily snap in the other parts. To use the corner drawer...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

Instructions Bill of Materials 3 or 4 - 1m OpenBeams depending on the size you want (6) 13/32" x 1" compression springs (44) 3m x 5mm screws (44) 3m nuts 1.75mm filament 4 corner open-beam corner pieces (optional for improved stability) 2 OpenBeam...

The Mongols had printed bank notes that were initially rejected by the public, an innovation they seem to have picked up from the Chinese. By the late 1,200s CE the Ilkhanate ruler Gaykhatu ordered the population to use them; they did not. A Sultan...

... is how we made it, it's a personal project, so it's ugly in places. I'm just putting this up here in case anyone wants to do this, or do this differently, or use it for something else. Or just print an overcomplicated Bender head, idk. ... Peace.