3d printing by muckychris

Build what you need ! Print instructions Raspberry PI Case File Comment RPI Case.stl The box to hold the Pi *1) RPI Case Lid w camera B.stl The lid, with pins to hold the camera RPI Case Lid w camera C.stl The lid, with...

They can be printed with PETG, ABS, or Nylon materials, but PLA is not recommended because it's not elastic and heat resistant enough. Type 1a: Car Mini Relay Socket This type of socket has five contacts that are 6.3mm in width and is designed for...

MegaMAME is a large console which can be stood on a table, or you can use the stand to hook it over your knees while sitting on the couch :-) I had to split the case into two parts to be able to print it on my Ender 6. I'm happy about how it turned...

... for reference, obviously these parts are available from numerous sources and you may already posses some of them. ... The case and the lid were printed with a 45% infill from PLA but PETG could also be used. The feet were produced using TPU. ...

Here are the necessary components: Raspberry Pi Zero W (1) Screws (2.2 x 4.5mm) (7) Nano Servo (e.g., Turnigy T541BBD) (1) Videos demonstrating the project in action can be found here: https://www.youtube.com/watch?v=_hPZF4_aZSA...

"HARFANG" X4 DRONE Special design for a drone X4 with Open HD hardware VIDEO TRANSMITTER OPEN HD (Rasberry pi zero + RTL8812AU) Go to OPEN HD github site : https://github.com/OpenHD/Open.HD ELRS happy model transmitter EP2 Go to Express LRS website...

It uses 2 locating dowels to press into the block's bellhousing pattern, and lines up to 3 bolt holes, so you can verify the print is accurate. Use this as a guide to hog out all the material within the frame. Note: before this stage, ideally, you'd...

BOM: the printed part 1/2 wavelength of solid 6ga copper ground wire (plus a little for trimming) coaxial cable coaxial connector for your cable To assemble the antenna: Cut two lengths of the 6 ga copper wire a little longer then 1/4 wavelengths...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

Cyl Pin Diameter Bottom = (0.5,1.0,1.0) Cylin Separation = (3.81,3.00,0) Layer Thickness Value = (0.30,0.29,0.28,0.27,0.26,0.25) Key Blade Width = ((Five Cylinder Key Blade Layers*Layer Thickness), 7*Layer Thickness,0) Print Layer Thickness = 1 Back...

(I would definitely suggest retracting when fitting the slider as it is a tight fit, and you could damage the tip of the wiper during assembly) I then recalibrated using raw data, and it is very smooth and accurate I printed this upside down with...

The zip files contain the STL files for the parts to be printed, but also the complete 14-page manual on the technical configuration of the robot. ... Videos available: Operation: https://m.youtube.com/watch?v=ApX3t5t67Fg&t=22s Assembly: ...

Fishing the wires through the print is a little tricky but not difficult. Longer screw is for the battery latch and sandwiches all parts of the adapter together for strength. I used flat head socket screws since I had them, but any flat head M3...

I strongly recommend printing Mpooh's fuse holder and wiring in an automotive fuse in series with the battery. The battery probably has protection circuitry, but who knows how much power this battery can supply before protection shuts it down. I use...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

Here's what you need to print: **Big Box** - primary gameplay components * 1x Map Tiles * 1x Features * 1x Missions * 5x Agencies x5 * 4x Joint Ventures x4 * 1x Outcomes * 1x Time * 1x Points * 1x Calendars **First Small Box** - Advancements and...

I printed the body and other parts, mounted the sensor in the sensor mount then glued the parts in place. As for the missing parts, get these from the original design that I remixed this from. ... Link to downloads for motioneyeos:...

PRINTING ----- Nothing needs supports. I use transparent PLA for everything. I would recommend using the same colour for all mounts, but you could also colour them to match the cap, or code them to the country they come from or something if you...

Dewalt 12v DC Power supply and USB Source first you need to print DeWalt Battery Adapter. XL4015 or HW-083 dc Converter. M3430 Volt-Amp Meter . Power Switch :. Fuse Socket :. Fuse 20 Amp:. Banana connector :. Self Tapping screws kit:. M3 -...

The rods should be cut to length (about 86mm, give or take, size them up against the holder once it is printed). I'd recommend cutting them so that they have about 1mm to 2mm play side to side once installed; if cut too snugly they can extend past...

The V3.1 box has been on the printer for around 150 hours of printing with no evidence of overheating of the TMC drivers or the Raspberry Pi. I had to ramp up the ref voltage for the 4988 extruder driver from 0.72 to 0.85 to alleviate some skipping...

Most PC fans should fit since there aren't any thickness constraints, if you have a thicker or thinner fan then the parts will fit around this.The fan is modular so you can print what you want and perhaps design your own parts. I've included the...

For this version print two large gears, both large and small shafts, one motor gear and the motor box. This add-on might fit on the other models this is based on like rmcht’s Double Gear Grinder and the Dual Drive system of claxly. There would be...

Added on October 29th: CSS Charleston CSS Chicora CSS Colombia CSS Huntsville CSS Louisiana CSS Mississippi CSS Missouri CSS Muscogee Added on November 2nd: CSS North Carolina CSS Raleigh CSS Richmond CSS Savannah Updated on November 12th: Converted...

It's also very easy to print with. Use the photos for reference of my assembly description. Motor mounting Cut a piece of thin double adhesive tape about 5x5mm in size. Stick the tape to the inside of the motor holder on the frame. (See picture) ...

The pegs are quite thin, so it's best to print them with a layer height of 0.08mm. This setting should make the pegs strong enough to hold up to inserting into the bracket but flexible enough to slip into the bracket with little force. I've also...

The SKR v1.3 board mounts with M3 screws, directly into the printed plastic. The holes are 2.8mm diameter, so the M3 screws will cut threads into the plastic if you turn slowly with pressure at first. This works best with PETG, but also works with...

I would recommend printing with 100% infill. Included in the download is the sketchup source file for your own customization (Hint: I always include my source files). UPDATE!!! I still need to determine the pinout. I will post it up here once I...

Printing without support is required for this fan duct. Secure the fan with 2 M3 x 10mm screws and attach the duct to the carriage using 2 M3 x 25mm screws, with nut traps built-in for additional tightness. All measurements are in mm. #Response...

Hello everyone, I've successfully converted my MegaTronXY X1 into a CoreXY Printer with an impressive printing area of 400x450x370. After learning about the remarkable speed of CoreXY printers, I decided to give it a try and upgrade my machine. So, I...