3d printing filament guide

Hello.I need to “repair” my 1080Ti fans because they started to make some weird noises and low the rpms, temperatures go higer, and… why no temperature and noise reduction upgrade ?First I want say the photos are of the first functional prototype,...

The design is somewhat double-brick out-house in most places and doesn't require high-resolution printing, such as wafer-thin walls. However, it will produce a robust system that people may like to refine themselves. OpenSCAD files are provided to...

Printed in PETG with .2mm layer height. PETG is recommended if you're going to put this in your aquarium. The more infill you use, the less buoyant the rack will be in the water, also depending on the wall thickness you use. The provided Suction...

Please note that if the magnetic tension is too high - for example, if the magnets are too close together - this can soon lead to the printed parts bending. There are two tops to choose from. Here's a video: https://youtu.be/lwLGZ7oSHqY As...

The print should fit snugly between the power supply connector and the RF shielding. If you happen to have other jacks, just go ahead and check the OpenSCAD source how to modify it according to your needs. ... Finally: Have fun playing the old...

... Note that the edge and corner brackets extend 6mm past the edge of the P5 panels, so make your wood frame 12mm larger than your matrix in each direction. Note - the picture doesn't show all the brackets attached yet because I'm still printing them.

This is accomplished by printing a column of fanned-out light pipes that radiate from the LED. Continue reading below the videos! Videos: They are all extremely short. Warpcore running at warp factor 2 Warpcore Standard from Novel Mutations on...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

It's just not a priority at the moment. I have never printed these out for testing/fitting purposes. If you do, please let me know so I can modify/update them as necessary.</p> <h3>Motivation &amp; Inspiration</h3> <p>The Kelly Take-offs don't look...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Margo,...

This can be inserted in a 6 inch flexible duct tube (used for outgoing ventilation) to prevent paper towels and the like from being sucked all the way to the inline duct fan (stalling it and requiring disassembly of the ducting to extract the paper...

The zip files contain the STL files for the parts to be printed, but also the complete 14-page manual on the technical configuration of the robot. ... Videos available: Operation: https://m.youtube.com/watch?v=ApX3t5t67Fg&t=22s Assembly: ...

It's a relatively simple print. To get this up and running, you'll need the following: 2019-03-02: I updated the design because the old one allowed big bugs in, and they got cozy on the Raspberry Pi. This new version should be bug-free. I also...

There is not any planet nor dwarf planet in the Solar System based on carbonaceous material, but it is theorised that a carbon based planet could exist in other planetary systems.Type: Asteroid.&nbsp;Orbit: Sun. Main Asteroid...

Flite Test sells Gremlin frames made from 3/32 (.094) inch thick Delrin or Carbon, and now you can print your own frames using the same shape files used by Flite Test to cut the delrin and carbon frames. The frames are incredibly durable and work...

For VTX antenna, I use TrueRC Singularity short ufl LHCP antenna https://www.racedayquads.com/products/truerc-singularity-5-8ghz-short-u-fl-antenna-rhcp-or-lhcp?variant=31387077476465 Print using 0.2mm layer height. 100% infill with support. For...

If you decide to set it up just like me, you'll only print the front case STL. But if you'd like to set the LCD in the bottom position, you'll need the back STL too. UPDATE 2: Added a 40mm silent fan, enabled only when drivers are enabled and last...

I am in the process of test printing with this setup. Edit 9/29/21: The Extruder mount bracket may not be needed if the three bolts are replaced with 3x M3x35 bolts. The adapter should be tight enough inside of the V6 adapter. Edit 9/30/21: I...

Besides printed parts, you'll need to complete these hardware requirements: Lid: (Button Head Screws ONLY) Six M3 6mm or 8mm Button Head Screws Eight M4 8mm Button Head Screws Inside Box: All Boards: M3 4mm Button or Cap Head Screws Fans:...

These are the various frame fittings to go along with the replacement X carriage parts for the toolchange system, here: https://www.thingiverse.com/thing:5149609 Note that this is not a stand-alone toolchange system - these two sets of parts are...

... to others work. A full list of items used appears below, feel free to share your prints and more items to come as time permits. Original Surgical Mask Strap Retainer was created by Thingiverse user Arrow_Archer and is licensed under cc-nc.

Here you will find blueprints for the 220mm carbon frame, blueprints for the electronics protection to be milled out of aluminum, and some printed models. Assembly video - https://www.youtube.com/watch?v=QfWXixFQmGc I used 3mm carbon for the...

... version, but it's overkill. It's also harder to line up with a wall stud due to the triangular arrangement of the screws. So, I made the two-screw version to share with others.I printed the anchors in PETG with three walls and 20% infill.

I have a modified version ready for printing, or you can simply cut out the piece that's in the way and make a new one. That's how I did it. V2: But if you want to order a new display and do some modifications, you can also just swap the original...

I was constrained by the size of the rotary switch and the USB breakout board otherwise it might have gotten a bit smaller. See it in action: https://youtu.be/PTTVuVUZYM8 I have included the OpenSCAD file which is somewhat parametric. Print...

... or peat swell pots stand is rather warm than cold compared to glass or metal. Print parameters for me: Infill 10% Layer height 0,18mm Speed 60mm/s Speed 1st layer 20mm/s Outer contours 3 Translated with www.DeepL.com/Translator (free version)

The smallest scale (1:500) is perhaps too small to be printed with FDM technology, but it may be printable in resin (SLA or DLP).The file's names explained: name_1_x.stl is 1 : x. So _1_500 is 1:500 or one in five hundred.</p><p>I spend part of my...

... convenience. Feel free to modify them however you please and post remixes for the community to benefit from! Print Settings: * Printer: Flash Forge Creator Pro * Rafts: No * Supports: Yes * Resolution: 0.200 microns for most parts * Infill: 40%

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

I have printed the lid in white PLA with slight indents for added light to come through at the right places. (it allows me to see the LEDs change so that I know it is working and not hung.) The lid is a (tight) push fit that stays in place well and...