3d printing nerd

August 17, 2018 I added videos with Banebot wheels and improved stepper support: https://youtu.be/ayka_9WWK08 https://youtu.be/4J9OeD_G4EI https://youtu.be/0Lg4ioItwHg March 10, 2018 First garage tests: https://youtu.be/bwohv99UVjI...

There's a newer version available at https://www.thingiverse.com/thing:3688067 that offers better rigidity and simplified printing and assembly, so I recommend using it instead. This older version is kept for reference purposes only. ![better...

#### What you need * The three printed parts * A cheap green laser pen like [this one](https://goo.gl/8AaT9K) (others could work the same) * 6 x M3 screws (I use 16mm, I think 12/13mm is great) Cost: less than 5€ .. Not bad ;) #### How to use it ...

Now fit the 80 tooth pulley printed part and secure with M5 screws and nuts. Check how long the rod needs to be by fitting the orange metal part that attaches the weights. Measure the gap between this part and the pulley. Remove the metal part and...

Details and links in the description below. Print instructionsI  used Fusion 360 for this project. Thank you Autodesk for letting me  play with your amazing tool! </p> <p><strong>NOTE</strong> The Fusion 360 file attached as a ".f3d" file but the...

The keyboard's design is based off the Preonic layout.&nbsp;Printed on MK3S at 0.2 layer height and brim in Prusa PLA Silver. No supports, make sure to have the bottom correctly set on the build plate.</p><p>What you will need in addition to the list...

... "WITHOUT". Keep in mind that you will loose 1mm of lenght of the screw for the heatbreak fan as shown in the last picture. Print instructionsPrinter Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 0.2 Infill: 30% Filament: CF-PETG

### How to Assemble the Clamp Charger: Print out all the parts and check if they fit together. The clamp holes might require some fine-tuning of the holes on the clamp (this depends on the material you selected for the clamp and cradle). After a...

You only need to print one lid for an entire stack. The idea is that you simply pull out the component boxes, unstack and remove the lids and the components are ready to go, in bowls, so your components are neat on the table. The magnets are placed...

The rods should be cut to length (about 86mm, give or take, size them up against the holder once it is printed). I'd recommend cutting them so that they have about 1mm to 2mm play side to side once installed; if cut too snugly they can extend past...

The mount model is positioned upside-down for printing without support. The interface between the mount and the clamp is a tapered wedge. This takes an instant to drop the Demel into, and it wedges tighter the more it's pressed down. Lifting the...

When I printed it, I placed the A blocks right next to the B blocks in the slicer, so they were already joined together. Here are the coordinates in case you want to get neighboring pieces, or need them for whatever reason. I'm also including...

If you print it, please post a make with pictures of the end result! Thank you! For all Ender 5 and Ender 5 Pro users! By now you probably have your crappy landy power supply clone swapped out for the Meanwell LRS-350-24 power supply! So now you got...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

The belt path is not flat, and the printed dual belt clips I have here will fail after about 175 - 200 hours of use. I will tinker with the design a little, but what I recommend is to use a linear rail for the X axis. This will also help you avoid...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

Use 5050 LED's!&nbsp;&nbsp;BOM:12v LED...

I made a battery pack for my TS100 soldering-iron. It is a 6S battery pack made out of 18650 cells. With the cells I used it should be possible to solder at least 3 hours without a break. I also used a Lipo Battery Voltage Tester that shows me the...

I printed the attachment upside down, using supports and 100% infill, since it needs to be airtight or nearly so. For the seal, I used Oomoo 30, a rubbery silicone mold compound. Other types of rubber with similar properties should also work. Once...

Thicker panels and prints good now in 1/25th scale *UPDATE: 10/09/21* Uploaded a revised truck bed, this time with wall supports, Rev B *UPDATE: 10/06/21* Revised the truck bed, made the walls a little thicker and smoother, Rev A for both Pro Street...

Fill with 1" of water or enough to reach halfway up the micro-trays, place trays in water and allow them to soak for 5-10 min depending on how compact the soil is and how much root mass is present.\r\n\r\nMicro-trays can be washed in the dishwasher...

Besides printed parts, you'll need to complete these hardware requirements: Lid: (Button Head Screws ONLY) Six M3 6mm or 8mm Button Head Screws Eight M4 8mm Button Head Screws Inside Box: All Boards: M3 4mm Button or Cap Head Screws Fans:...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   Description To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of penhold...

Can be printed with a moving head. Arkham Horror investigator - the professor by Craigen https://www.thingiverse.com/thing:4649571 Longboi Trophy by HiyuMarten https://www.thingiverse.com/thing:4706958 Stoat by Davision3d ...

The theory behind combining these two prints is that the stronger frame of the RebeliX printer and the amazing mechanics of the MK2 can be merged to create the ultimate Prusa-style printer. That's our interpretation, anyway. Visit davtr's MK2-X page...

Cyl Pin Diameter Bottom = (0.5,1.0,1.0) Cylin Separation = (3.81,3.00,0) Layer Thickness Value = (0.30,0.29,0.28,0.27,0.26,0.25) Key Blade Width = ((Five Cylinder Key Blade Layers*Layer Thickness), 7*Layer Thickness,0) Print Layer Thickness = 1 Back...

If they break reprint your model and try again or just glue it in place Reassemble you should be good at this point (unless you didn't test it along the way) Post-Printing This is my video on how to assemble the kit and the mod, it's also a video...

It is a snap-fit model that can be assembled without tools.● About printingAll parts can be printed without support.We recommend printing with PETG or ABS filament.&nbsp;It also works with PLA, but it may break if you pull the rod hard.The printed...

&nbsp;PLACING IT ON THE WRONG LEG IS A HIGH RISK TO YOU.You could use this mechanical design and limit switch to interface with the low-voltage system, but you will have to provide the required software modifications.There are several adjustments...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...