GoPro scope mount 3d models

Changelog2022-08-23v1.01increased infill and perimeters for all caps2022-08-21v1.0initial public releaseUnused space in Zero Motorcycles XMX swingarm? Create sealed storage space for warning vests, emergency candy, charging cable, tools,...

I cannot be held responsible!The cutter would cut other materials provided that they are no thicker than the 2mm slot height (& a Stanley blade is capable of cutting it!)The base has 4 mounting holes that will take M4 hex head bolts to allow the...

The process of adaptation presupposes that practical aspects of printing the model using the DLP/SLA/LCD technology are taken into account, and the model's scale and cutting are chosen to ensure an optimum result of printing.3D PRINTING...

It contains a 24V 12000 mah rechargeble battery and MoOde audio software.https://moodeaudio.org/Please press on the Like button?Parts needed:Raspberry Pi 3B or 3B+Raspberry Pi 7 inch touchscreenHifiberry AMP2Micro SD card class...

Bathroom Accessories Corner Shelf Shampoo Holder Kitchen Storage Rack Shower Corner Shelves Wall Organizer CSWO-02 Beautiful eco-friendly and concise form, comfortable sides preventing objects from falling, the mounting points of screws are...

Do note tho, that polycarbonate wheels are mandatory to get the best quality, and that the Z-Motor mount has a micro-tilt adjustment to perfectly align the leadscrew to the bed assembly * Why no ABL/Mesh BL ? because the aim here is to not really...

Mount the fathom board using M3 bolts and spacers, and attach two of the tether wires. When everything is ready to be assembled, run a bead of rtv or silicon around the edge of the box in the gasket groove, then bolt the lid down. Allow to dry for...

I centered the holes in the plastic inserts for simplicity, but because of the original design of the vise itself, its mounting holes (slots) are not symmetrical and thus the stand will only fit one way onto the frame properly. The stand has four (4)...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

Fit the spool base complete with M8 spindle to the top of the four mounting turrets in the centre of the dehydrator base and secure with four M3 x 16mm cap head screws, making sure it sits flat on the four turrets so the spindle is vertical. You...

Secure the rod with the 2 setscrews in the yoke. Mount the yoke bracket on the bigpulley with the 1/4-20 bolts and standard washers. Adjust the position so that the gears engage fully, but without too much friction. Now tighten the clamp on the worm...

Lenthal class destroyer In FASA Trek, Andorians had a thing for protected center mounted nacelles, and ships they had a hand in designing showed this. The Lenthal features a strange teardrop shaped extended hull. Nelson class scout FASA's...

Mk5-T should work on other phones as well. Actually did some more testing with other sticky tacks, specifically LocTite Fun-Tak Mounting Putty (http://smile.amazon.com/dp/B001F57ZPW) and it works really well. Very happy with the results.</li> </ol>...

You do not lose 3mm of Height (3mm higher like the commercial Version will cause that the firmware calibration process runs into an error).I used the Extrusion to mount the Rails rather than the original mounting holes. That's much more robust in my...

It now has 2 mounts for 28BYJ-48 steppers motors inside the palm to operate the fingers - I plan an using one for the thumb and the other for the rest of the 4 fingers. I printed a first prototype and found out that the joints I printed (100% infill)...

For the table clamp mounting option that is linked to above, you will not need the ground plane part.That's it, your vice is ready to operate.License:The license does not allow derivatives, as one of my designs in the past was “taken” from me in the...

This is a slide-in case, and since the cable has a 13x5 mm (-ish) connector, there is a rectangle hole to put the cable through. The small part acts as a strain relief for the cable and at the same time to plug the rectangle hole in the back for the...

I created this https://www.prusaprinters.org/prints/93074-prusa-mini-x-stepper-cable-guide and it works very well for me. To be always informed of humidity and temp in the enclosure I use this mount for standard round cheapo hygrometers:...

In the 1.1 update: Hub now supports standard hobby servo mounting arms/horns. Renders flat. It's important to note that you can configure this wheel to such an extend that it may not be printable at home with extruded plastic printers. In these...

for my build I wanted a night vision camera so I used a raspberry pi NOIR camera and IR Leds along with a 3amp 12v to 5v convertor, 5v feeds the PI and 12v powers the IR ring. I printed the body and other parts, mounted the sensor in the sensor mount...

You'll need to print 3x End Caps, 44x Flipper 1, 4x Flipper 2, 3x Flipper 3, 1 Knob, and 28 Flipper Mounts. It works best to print the end caps with different colors that will make it easier to identify the start and the end of the maze. The...

If you want to retrofit the blower fan and this duct on an older printer that does not have the mounting bracket, you can print my clone of it.   Using Just as with the stock duct, a limitation is that it only blows in one direction, meaning that...

You want to be able to draw a virtual line through from the first gear on the mounting plate to the gear on the pot straght through a pair of small dots on the factory gears. Look very close and you should see what i'm talking about. After this...

The only surface mount component on the boards is the L9110s but it's it can be easily hand soldered. The resitors are all 1/8 Watt. The gerber files for having the boards maufactured will be on the Github for either the Picaxe ar Attiny board.You...

Important to ensure the aft portion of the Barrel which goes into the mounting hole is glued to the CF. 3. Precision drill the thru holes in the Nose to just fit the ~3.1mm aft side of the Barrel. I used an electric hand drill. Be careful to align...

Make your own custom chips.Accessories&nbsp;DescriptionImageFCS Label Mounting SolutionUse this to label what filament is stored in your dry box, Ikea samla or where ever else you want to label filament.FCS Label StandUse this to see what material...

Since many of my friends own the 18V Makita battery system I thought of a practical Christmas present for them.I got the idea for the basic platform from user "bitplusatoms" with his design "Makita Battery Mount"...

Patience at the time to assembly It is also recommended, above all if it is the first time that you mount something, you do it somewhere quiet, with enough space to see all parts and work in a comfortable area. <Brr! I had never build one before...

Here is a listing for an assortment that I got mine from.https://www.amazon.com/dp/B07VS4823F?psc=1&ref=ppx_yo2ov_dt_b_product_detailsThe other aligner is printed but is wider not using the pipe.There is one more option if people want to drive the...

Added the ability to control the depth of an engraved svg image.UPDATE 22 Jan 2021 (version 36): Fixed bug that allowed you to choose a mounting method other than slide-in tabs and no mount for a laser-cut keyguards. Fixed bug that put a chamfer on...