Modular Token Holder 3d models

Camera assembly Put some insulation tape around the outer side of the objective holder. This will help to avoid blinding stray light caused by the IR-LEDs. <p>Plug the camera into the designated hole at the rear side of the adapter ring. Put some...

To attach, mount your Reprap 3D hotend in its holder - while still making sure it’s fully aligned properly on your metal cooling rod assembly system. You may be able to apply just enough pressure against each end so the parts will stay where they...

Arm 60 can handle most of the small 1” good compact cameras, Arm90 is situated for longer combos or when holding a phone upside down (light phone holder needed). The screws I used as a model are https://www.amazon.it/dp/B07V6K4DQS and they will...

Big wood screw to hold the cables from the cable holders - get creative here! Some Teflon tube to fill the lower guide, upper guide, and filler screw. Some Amazon items I found that match what I'm using: ...

- 24V LED strip, attached to this design: Creality Ender 3 LED strip holder. You can use a 5V LED strip, when you power it from the buck converter instead of directly from the PSU. - 9x M3 8mm screws (relays, buck converter, lid), 2x M3 12mm screws...

The tools used for assembly include: Files in various shapes Super Glue A handheld drill with small drill bits A soldering iron with solder Pliers for cutting and stripping wires 3D-printed components used are: Handle Grip A (1 piece) Handle Grip B...

The enclosure has quite a few parts, on the bottom part of the case comes the piCam breakout, a gap filler evens the surface, then the ring holder. These 4 layers get fixed with 2 m2x10 screws. Then the led ring is place on the ring, turn it until...

... the hole. Twist to align with the blade openings in the battery. This video should help you visualize the battery box: https://www.youtube.com/watch?v=OYVdm-FmvfU Fabricate a small fuse holder using two female F connectors and an ATX 7.5a fuse.

Print new probe holder I designed a probe holder with a channel down the side that would fit the thermistor, allowing me to get a pretty good guess as to the temperature of the probe. It's designed to fit into my modified BLTouch mount for the BMG...

All the screw holes are meant to be self-threaded by the screws, so I recommend printing the Top Cover (to test M4 holes) and an Amplifier Holder (to test M3 holes) first. <h3>Wiring</h3> The above image shows how a PC817 or EL817 opto isolator is...

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: [>>>] Generating [0] Thing Title : Mosaic Filament Drive Mounted Guide [0] Thing URL : http://www.thingiverse.com/thing:32085 [0] Thing Author : andrewbarton [0] Thing...

After making the top mount hub holders (found here http://www.thingiverse.com/thing:1752018), I didn't like my method of spool hubs. A simple plate style hub mount is fine when you work with one company for filament, and they don't change the spool...

List of items used in this project and where to find them: ■ Elegoo Arduino Uno (x1) - https://geni.us/ArduinoUno ■ Micro continuous rotation servo (x1) - https://geni.us/360MicroServo ■ Micro 180º servo (x1) - https://geni.us/MicroServo ■ LM317...

Version 3: The assembled wing measures 40cm (400mm) using three printed parts and includes a camera holder with built-in control horns, pushing the CG slightly forward. To print this version, use the yellow and red pieces shown in the photo. I...

The display holder is foldable around the 18650 battery tube and can only pass through the glasses neck when folded. Insert (glue) the wired WS2812B LEDs, on top the wired TTP223 and fold the two halves together to insert into the glass. When...

With its versatile design, you have the option to either screw the legs out and hang it from the ceiling or use the convenient leg holder to keep them safe when not in use. Credit to tato_713 who made this death star I just remixed this...

On the photos, you can see that I glued the Neo Pixels onto the LED holder first and then connected them with wires. The 5V power comes directly from the Arduino, and the data output is set to pin 2 in this example. I included a simple sketch for...

Place the nut on the end of the 10-32 screw a few turns and use the screw to insert the nut into the recessed nut holder in the side of the holster. Take your spring clip and slide it into the slit on the screw hole side of the top of the holster. At...

You also need to get the camera holder printed (TPU should be the best option). ... #### Recommended setup - 1105/6 motors - Brushless AIO board (ex :...

I designed the main card tray with a ramp at one end so it will hold all the project cards vertically without them spilling out of the holder. This is similar to the cardboard ramps provided in the Terraforming Mars Big Box, except this ramp is built...

To install the Z damper: 1x printed detail from here: 2x short M3 bolts 2x M4 bolts (like the original Z motor holder screws, but shorter and with t-nuts) - I don't recommend messing with original bolts in case something goes wrong. You can print...

Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work. Our puzzles are modeled using the open-source...

The blade holder has a certain amount of cutting depth adjustment that can be made by turning the top dial. However, your Z-stop height may need to be changed to use this attachment effectively. The adhesive mat (not shown) is clipped to the bed and...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

After you get that leveler put on it's really no biggie to add a bit of hardware, just make sure to have enough clearance so your wires stay within the holder. We will not use them with this one so the new X carriage has some modifications too. A...

It's not really designed to go with anything in particular, I just wanted to make it as a gift box or candy holder sort of thing. Would be pretty easy to customize by putting a design along the side. This prints in 5 pieces that hold together...

Standard size [Thing:3922866](https://www.thingiverse.com/thing:3922866) * 1Kg Filament in Dremel 3D45 Solution #1 [Thing:3818976](https://www.thingiverse.com/thing:3818976) * 1Kg Filament in Dremel 3D45 Solution #2...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

This is a remix of the ZWO EAF Holder for Celestron Nexstar 6/8/9 by jamesdedij (February 29, 2020) for the Celstron SCTs and I thank him for sharing the editable design files with me. I have modified all of the parts in Fusion 360 to fit the...

I've seen some under-extrusions due to the lack of a proper filament roll holder, so that needs fixing soon. I'm testing a counter weight system for the bed to make it seem lighter and more accurate. ...The next project is enclosing the printer body...